OPB970L51 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The sensor> OPB970L51

OPB970L51: DescriptionSWITCH SLOTTED OPTICAL WIRE LDS; CategoryThe sensor; File Size1018KB，6 Pages; ManufacturerTT Electronics; Environmental Compliance

Download Datasheet Parametric View All

OPB970L51 Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	OPB970L51	-	-	View	Buy Now

OPB970L51 Overview

SWITCH SLOTTED OPTICAL WIRE LDS

OPB970L51 Parametric

Parameter Name	Attribute value
Sensing distance	0.125"（3.18mm）
Sensing method	conductive
Output configuration	totem pole, buffer
Installation type	Through hole
Current - Power	15mA
Voltage - Power	4.75 V ~ 5.25 V
Response time	70ns
Operating temperature	-40°C ~ 70°C（TA）
Package/casing	PCB installation

Preview

Download Datasheet

View All



Choice of logic and output driver circuits

Choice of aperture size, covered or open

Wire or PCB leads

Choice of mounting features

Direct TTL, LSTTL, CMOS Interface

The OPB960/ 970/ 980/ 990 series of non-contact Photologic

slotted optical switches provides flexibility in meeting

application specific requirements for the design engineer.

Building from a standard housing with a 0.125” (3.18mm) wide slot, the user can specify output logic state, output driver

circuit, aperture width, aperture surface and mounting tab locations. Furthermore, an option of wire or PCB leads allows

electrical interface flexibility.

The device body is an opaque plastic which minimizes sensitivity to both visible and near-infrared external light sources

which may impact operation. Aperture width choices provide different optical resolution for motion sensing. A covered

aperture provides dust protection, while an open aperture provides maximum protection against external light sources.

Electrical operation is over a wide supply voltage range. LED emissions are near-infrared (850—940nm).

Detector digital output logic choices of buffer or inverter with totem-pole or open-collector driver circuit simplify interface

for various electrical requirements.

Custom electrical, wire and cabling services are available.

Contact your local representative or OPTEK for more information. Compliant to EU RoHS Directive 2002/95/EC



Speed and direction

indication



Rotary encoders



Mechanical switch replacement



Mechanical limit indication

Part Number Guide



Printers - Top of form, End of travel, Home position.



Sliding Door Automotive and Lift gate applications

OPB 9XX X XX X

OPTEK Assembly

Photologic Sensor Family

Slot Aperture Surface and Lead Options:

6 —

Covered (apertures not visible), PCB leads

7 —

Open (apertures visible), PCB leads

8 —

Covered (apertures not visible), Wires

9 —

Open (apertures visible), Wires

Logic and Output Driver Types:

0 —

Buffer Totem-Pole

1 —

Buffer Open-Collector

2 —

Inverter Totem-Pole

3 —

Inverter Open-Collector

RoHS

Z =

Wires only, None for PCB leads

Aperture Width Guide Options:

55, 51, 11 ( See Aperture Width Guide )

Mounting Tab Location:

L —

Emitter

N —

None

P —

Sensor

T —

Both (two mounting tabs)

Logic Type

Buffer

Inverter

Input

LED

OFF

Output Log-

ic State

LOW = 0

HIGH = 1

Recommended Resources

30 to 50℃ temperature control circuit

Transformerless DC-DC converter circuit diagram

TDA1020 power amplifier circuit diagram

Three-phase power supply phase sequence indicator circuit

Fuse blown music alarm

Serial communication protocol rs232.docx: Serial communication protocol rs232.docx...; 雷北城 EE_FPGA Learning Park

What are the two options of PCB copper cladding that people usually set?: [i=s]This post was last edited by sky999 on 2020-8-9 14:01[/i]Are these two options usually set to default? I have always set them like this, do I need to adjust them? Because I didn't adjust the copp...; sky999 PCB Design

Microcontroller programming using C library functions: 1.printf function This is very simple. Just redirect the printf function. This is the STM8L microcontroller code. Note: If it is an IAR compiler, you need to enable library-FULL It can be used on msp4...; 火辣西米秀 Microcontroller MCU

Design of large LED display system based on FPGA+MCU: The traditional large-scale LED display system uses MCU, ARM or PLD as the core control chip. The LED display control system with FPGA as the core is relatively complex to design and implement, and ne...; led2015 FPGA/CPLD

【Development Kit for nRF52840】+Being beaten by nordic: I tried 52840 on the weekend, and found that it was beaten by n companies :Cry: I am still too green. I saw on the forum that 52840 can be downloaded with mdk before. I thought that I had installed md...; lehuijie RF/Wirelessly

MCU on-chip memory burning (ROM programming): The microcontroller application system consists of hardware and software. The carrier of the software is the program memory of the hardware. The program memory uses a read-only memory. This memory can...; fish001 Microcontroller MCU

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components