ADVANCED ENGINEERING
Technical Data Sheet
A DVA N C ED EN G I N E E R I N G
Te c hni c a l D a t a S h e e t
Put-Ups
Up To 20 Times Stronger
Than Steel
Will Not Melt, Burn Or
Support Combustion
Stays Soft, Flexible And
Pliable Throughout -274°F
to 320°F
Nominal
Size
1/4”
1/2”
3/4”
1”
1 1/4”
1 1/2”
2”
Part
#
KVN0.25YL
KVN0.50YL
KVN0.75YL
KVN1.00YL
KVN1.25YL
KVN1.50YL
KVN2.00YL
Expansion Range
Min
1/8”
1/4”
1/2”
3/4”
1”
1 1/4”
1 3/4”
Max
5/16”
5/8”
7/8”
1 1/4”
1 5/8”
2”
2 1/2”
Bulk
Spool
500’
250’
250’
200’
125’
100’
100’
Shop
Spool
50’
50’
50’
25’
25’
25’
25’
Available
Colors
Yellow
Yellow
Yellow
Yellow
Yellow
Yellow
Yellow
(YL)
(YL)
(YL)
(YL)
(YL)
(YL)
(YL)
Lbs/
100’
0.30
0.80
1.20
1.92
2.40
2.90
3.60
Stronger Than Steel, Soft And Pliable
FLEXO ARAMID (FA) is a soft, flexible sleeving that’s
perfect for bundling and protecting vulnerable
components from the most extreme
environmental conditions. Flexo Aramid is
braided from aramid fibers and has all well-known
characteristics of durability, pliability and
extraordinary tensile strength. Flexo Aramid
fibers are up to 20 times stronger than steel fibers
of equal diameter.
Cut Cleanly
Flexo Aramid Shears
Material
Kevlar® Aramid Fibers
Grade
KVN
Wall Thickness
.020”
Drawing Number
TF001KV-WD
Flexo Aramid has excellent thermal stability,
permitting long-term, continuous use at temperatures
as low as -274°F and as high as 320°F. Short term
exposure up to 572°F can be tolerated. Flexo Aramid
does not melt or support combustion. The sleeving
provides extreme strength and durability, yet
is lightweight and easy to install.
The properties that make Flexo Aramid so tough in
use also make the material a challenge to cut
to length. Use Flexo Aramid shears for cutting.
NEW- Ask about our high speed cutting service.
Cuts Flexo Aramid to precise, repeatable lengths!
Colors Available:
Yellow (YL)
800.323.5140 • 973.300.9242 • fax: 973.300.9409
104 Demarest Road • Sparta, NJ 07871
www.techflex.com
ADVA NC ED ENGI NEE R ING
ADVANCED ENGINEERING
Tech n i cal Data Shee t
Technical Data Sheet
ABRASION
Abrasion Resistance
Maximum Continuous
320°F (160°C)
Mil-I-23053
www.techflex.com
Medium
Abrasion Test Machine
Taber 5150
Abrasion Test Wheel
Calibrase H-18
500g
80°F
70%
Abrasion Test Load
Room Temperature
Humidity
Scuffing And Pulling
Of Soft Fibers
CHEMICAL
RESISTANCE
1=No Effect
2=Little Effect
3=Affected
4=More Affected
5=Severely Affected
Minimum Continuous
-274°F (-170°C)
PHYSICAL
PROPERTIES
Monofilament Diameter_________ NA
ASTM D-204
Flammability Rating ________________
FMVSS-302 Approved
Cutting _________ Flexo Aramid Shears
Colors __________________________ 1
Wall Thickness__________________ .02
Tensile Strength (Yarn) ____________ 39
ASTM D-2256 Lbs
Specific Gravity ASTM D-792 ____ 1.44
Moisture Absorption% ______________
ASTM D-570
Hard Vacuum Data _________________
ASTM E-595 at 10-5 torr
TML _________________________3.13
CVCM ________________________ .19
WVR_________________________ 1.76
Smoke D-Max _____________________
ASTM E-662
Outgassing ___________________ High
Oxygen Index ___________________ 29
ASTM D-2863
20 Test Cycles
Scuffing And Pulling
Of Fibers Continues
400 Test Cycles
700 Test Cycles
Pre-Test Weight
Material Destroyed
5,730.5 mg
5,200.1 mg
530.4 mg
Post-Test Weight
Test End Loss Of Mass
Point Of Destruction
Aromatic Solvents ________________ 2
Aliphatic Solvents _________________ 2
Chlorinated Solvents ______________ 2
Weak Bases ______________________ 1
Salts ____________________________ 1
Strong Bases _____________________ 2
Salt Water
0-S-1926
________________ 1
Hydraulic Fluid
MIL-H-5606
_________ 1
Lube Oil
MIL-L-7808
_______________ 1
De-Icing Fluid
MIL-A-8243
__________ 1
Strong Acids _____________________ 2
Strong Oxidants __________________ 2
Esters/Ketones ___________________ 1
UV Light ________________________ 4
Petroleum _______________________ 1
Fungus
ASTM G-21
________________ 2
Halogen Free ___________________ Yes
RoHS _____________________________
SVHC _____________________________
© 2016 Techflex, Inc. - Any unauthorized reproduction, in whole or part, in any medium whatsoever, without the express written permission of Techflex, Inc. is strictly forbidden.
Techflex product names and logos are registered trademarks of Techflex, Inc., unless otherwise attributed. The contents and illustrations contained herein are believed to be reliable.
Techflex makes no warranties as to their accuracy or completeness and disclaims any liability in connection with their use. Techflex’s only obligations are those in standard terms of
sale for these products and Techflex will not be liable for any consequential or other damages arising due to misuse of these products or typographical errors or omissions.
11-15
Users should make their own evaluation to determine the suitability of these products for their unique and specific applications.
stm32/stm8
京公网安备 11010802033920号
EEWORLD
