Operating Temperature Range .........................
-40°C to +125°C
Maximum Junction Temperature
......................Internally
Limited
Storage Temperature Range
............................
-65°C to +150°C
Soldering Temperature (reflow, TQFN and WLP)
........... +260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Package Thermal Characteristics
(Note 1)
TQFN
Junction-to-Ambient Thermal Resistance (θ
JA
)
..........36°C/W
Junction-to-Case Thermal Resistance (θ
JC
)
.................3°C/W
WLP
Junction-to-Ambient Thermal Resistance (θ
JA
)
..........44°C/W
Note 1:
Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to
www.maximintegrated.com/thermal-tutorial.
DC Electrical Characteristics
PARAMETER
V24 Supply Voltage
V24 Undervoltage-Lockout
Threshold
V24 Undervoltage-Lockout-
Threshold Hysteresis
(V
24
= 9V to 60V, V5 = 4.5V to 5.5V, VL = 2.5V to 5.5V, V
GND
= 0V; REG unconnected, all logic inputs at V
L
or GND; T
A
= -40°C to
+125°C, unless otherwise noted. Typical values are at V
24
= 24V, V5 = 5V, VL = 3.3V, and T
A
= +25°C, unless otherwise noted.) (Note 2)
SYMBOL
V
24
V
24UVLO
V
24UVLO_HYST
C/Q and DO
disabled (CQ_Dis =
1, DO_Dis = 1)
C/Q and DO
in push-pull
configuration,
CL[10] = 11, C/Q
and DO high, no
load on C/Q or DO
C/Q and DO
in push-pull
configuration,
CL[10] = 11, C/Q
and DO low, no load
on C/Q or DO
V
24
rising
V
24
falling
CONDITIONS
MIN
9
6
6
7.8
7.2
570
0.14
0.5
TYP
MAX
60
9
9
UNITS
V
V
mV
V24 Supply Current
I
24
V5 powered
externally, REG is
unconnected
1.1
1.75
mA
1.4
1.8
www.maximintegrated.com
Maxim Integrated │ 3
MAX14827
IO-Link Device Transceiver
DC Electrical Characteristics (continued)
(V
24
= 9V to 60V, V5 = 4.5V to 5.5V, VL = 2.5V to 5.5V, V
GND
= 0V; REG unconnected, all logic inputs at V
L
or GND; T
A
= -40°C to
+125°C, unless otherwise noted. Typical values are at V
24
= 24V, V5 = 5V, VL = 3.3V, and T
A
= +25°C, unless otherwise noted.) (Note 2)
PARAMETER
V24 Low-Voltage Warning
Threshold
V5 Supply Voltage
V5 Undervoltage-Lockout
Threshold
V
5UVLO
V
5
rising
V
5
falling
C/Q and DO
disabled (CQ_Dis =
1, DO_Dis = 1), V33
disabled (V33_Dis
= 1)
C/Q and DO
in push-pull
configuration,
CL[10] = 11, C/Q
and DO high, V33
enabled, no load on
C/Q, DO, or V33
C/Q and DO
in push-pull
configuration,
CL[10] = 11, C/Q
and DO low, V33
enabled, no load on
C/Q, DO, or V33
VL Logic-Level Supply
Voltage
VL Undervoltage Threshold
VL Logic-Level Supply
Current
V
L
V
LUVLO
I
L
All logic inputs at V
L
or GND, all logic
outputs unconnected
REG = V5, no load on V5, 9V ≤ V
24
≤
60V
REG = V5, 0mA < I
LOAD
< 30mA, V
24
= 24V
REG = V5, I
LOAD
= 1mA, V
24
from 9V
to 60V
Internal regulator or external NPN
2.5
0.9
1.7
0.25
SYMBOL
V
24W
CONDITIONS
MIN
14.5
4.5
2.8
2.8
3.5
3.45
TYP
16.5
MAX
18
5.5
4.5
4.5
UNITS
V
V
V
0.64
0.9
V5 Supply Current
I
5_IN
External 5V applied
to V5, REG is
unconnected, no
load on LED1 or
LED2
1.37
1.75
mA
1.41
1.8
5.5
2.4
3
V
V
µA
5V LINEAR REGULATOR/CONTROLLER (V5)
V5 Output Voltage
Load Regulation
Line Regulation
REG Output Current
V
5
ΔV
5_LDR
ΔV
5_LNR
I
REG
4.75
5.00
0.02
0.01
5.25
0.2
4
30
V
%
mV/V
mA
www.maximintegrated.com
Maxim Integrated │
4
MAX14827
IO-Link Device Transceiver
DC Electrical Characteristics (continued)
(V
24
= 9V to 60V, V5 = 4.5V to 5.5V, VL = 2.5V to 5.5V, V
GND
= 0V; REG unconnected, all logic inputs at V
L
or GND; T
A
= -40°C to
+125°C, unless otherwise noted. Typical values are at V
I still remember the DIY work video of Mr. He shared on the forum not long ago. At the end of the video, there was an advertisement for the sponsor company. At that time, I thought this company was go...
At present, distributed systems based on the CAN (Controller Area Network) bus have been widely used in the field of automotive electronics, and the calibration of electronic control units has become ...
The photoelectric-contact liquid level sensor is a sensor that outputs analog signals. Its application circuit is shown in Figure 1.Figure 1 Application circuit
During the detection process, the outpu...
This article is to make up for the previous review, which I forgot to continue. Today, I will continue to test our Alibaba Cloud connection.
For more information, please refer to the previous review, ...
1.Sirf reference typical four or six layer board, standard FR4 material 2.All components should be surface mounted as much as possible 3.When placing the connector, try to avoid introducing noise into...
Previously, Chen Jin, general manager of Lenovo China's mobile phone business department, revealed in an interaction with netizens that the Motorola flagship equipped with Qualcomm Snapdragon 8...[Details]
If nothing unexpected happens, Samsung will continue to launch the new generation of Galaxy Note20 series flagships in the second half of this year. As June draws to a close, this blockbuster n...[Details]
// 0 sets the value in down_counter (beeping frequency)
//-------------------------------------------------------------
static int xiaoyang_beep_ioctl(struct inode *inode, struct f...[Details]
Early morning on March 16, according to foreign media Macrumors, according to the latest research, dozens of popular iOS applications read the contents of the clipboard without user consent, w...[Details]
What do you think of when talking about mobile phone manufacturers’ offline stores? Apple Store? Xiaomi Store? Or OPPO's flagship store? Since Xiaomi's great success online and the rapid r...[Details]
With the continuous development of modern science and technology, electronic products are constantly updated. The widespread use of single-chip microcomputers makes the design of current electronic...[Details]
Most current instruments implement their functions by combining a closed FPGA with fixed firmware. If you have ever seen a disassembled oscilloscope, you have probably seen the FPGA inside. FPGAs i...[Details]
This is the MCU stopwatch course design I made last month. This course design is to realize a stopwatch from 00 to 99 seconds, and it has start and reset functions. It took a week. The attachment con...[Details]
A grating is a photoelectric device composed of many equally spaced light-transmitting slits and opaque lines that are evenly arranged alternately. According to the working principle, gratings can be ...[Details]
At present, there are three main methods for LED to achieve white light:
1. Synthesize white light through LED red, green and blue three-primary color multi-chip set and light emission.
A...[Details]
At present, Japan has officially implemented material sanctions against South Korea. The export of three materials, namely fluoropolyimide, photoresist and high-purity hydrogen fluoride, to South Kor...[Details]
1 Introduction
In recent years, the number of fire accidents in China has been on the rise. Among the fire accidents, the proportion of electrical fires remains high, accounting for 27% of...[Details]
Cortex-M3 supports 256 interrupts, including 16 core interrupts and 240 external interrupts. STM32 has only 84 interrupts, including 16 core interrupts and 68 maskable interrupts. STM32F103 has o...[Details]
Traditional virtual instruments consist of a data acquisition board based on the PCI bus that directly uses A/D and D/A chips and corresponding software. However, with the rapid development of comp...[Details]
The integrated voltage regulator parallel current expansion circuit is shown in the figure:
Note: In practical applications, it is best to use the same manufacturer and model of voltage stabiliz...[Details]
Buy&Sell
京公网安备 11010802033920号
EEWORLD
