This product has been retired and is not recommended for designs. For new and current designs, S29AL004D supersedes Am29DL400B and is the factory-recommended migration path.
Please refer to the S29AL004D datasheet for specifications and ordering information. Availability of this document is retained for reference and historical purposes only.
DISTINCTIVE CHARACTERISTICS
■
Simultaneous Read/Write operations
— Host system can program or erase in one bank,
then immediately and simultaneously read
from the other bank
— Zero latency between read and write
operations
— Read-while-erase
— Read-while-program
— Sectors can be locked in-system or via
programming equipment
— Temporary Sector Unprotect feature allows
code changes in previously locked sectors
■
Top or bottom boot block configurations
available
■
Embedded Algorithms
— Embedded Erase algorithm automatically
pre-programs and erases sectors or entire chip
— Embedded Program algorithm automatically
programs and verifies data at specified address
■
Single power supply operation
— 2.7 to 3.6 volt read and write operations for
battery-powered applications
■
Manufactured on 0.32 µm process
technology
■
High performance
— Access times as fast as 70 ns
■
Minimum 1 million program/erase cycles
guaranteed per sector
■
20-year data retention at 125° C
— Reliable operation for the life of the system
■
Low current consumption (typical
values at 5 MHz)
— 7 mA active read current
— 21 mA active read-while-program or read-
while-erase current
— 17 mA active program-while-erase-suspended
current
— 200 nA in standby mode
— 200 nA in automatic sleep mode
— Standard t
CE
chip enable access time applies to
transition from automatic sleep mode to active
mode
■
Package options
— 44-pin SO
— 48-pin TSOP
■
Compatible with JEDEC standards
— Pinout and software compatible with
single-power-supply flash standard
— Superior inadvertent write protection
■
Data# Polling and Toggle Bits
— Provides a software method of detecting
program or erase cycle completion
■
Flexible sector architecture
— Two 16 Kword, two 8 Kword, four 4 Kword, and
six 32 Kword sectors in word mode
— Two 32 Kbyte, two 16 Kbyte, four 8 Kbyte, and
six 64 Kbyte sectors in byte mode
— Any combination of sectors can be erased
— Supports full chip erase
■
Ready/Busy# output (RY/BY#)
— Hardware method for detecting program or
erase cycle completion
■
Erase Suspend/Erase Resume
— Suspends or resumes erasing sectors to allow
reading and programming in other sectors
— No need to suspend if sector is in the other
bank
■
Unlock Bypass Program Command
— Reduces overall programming time when
issuing multiple program command sequences
■
Hardware reset pin (RESET#)
— Hardware method of resetting the device to
reading array data
■
Sector protection
— Hardware method of locking a sector to
prevent any program or erase operation within
that sector
This Data Sheet states AMD’s current technical specifications regarding the Products described herein. This Data Sheet may
be revised by subsequent versions or modifications due to changes in technical specifications.
Publication#
21606
Rev:
E
Amendment/+4
Issue Date:
June 7, 2005
GENERAL DESCRIPTION
The Am29DL400B is an 4 Mbit, 3.0 volt-only flash
memory device, organized as 262,144 words or
524,288 bytes. The device is offered in 44-pin SO
and 48-pin TSOP packages. The word-wide (x16)
data appears on DQ0–DQ15; the byte-wide (x8)
data appears on DQ0–DQ7. This device requires only
a single 3.0 volt V
CC
supply to perform read, pro-
gram, and erase operations. A standard EPROM
programmer can also be used to program and erase
the device.
The standard device offers access times of 70, 80,
90, and 120 ns, allowing high-speed microprocessors
to operate without wait states. Standard control
pins—chip enable (CE#), write enable (WE#), and
output enable (OE#)—control read and write opera-
tions, and avoid bus contention issues.
The device requires only a
single 3.0 volt power
supply
for both read and write functions. Internally
generated and regulated voltages are provided for
the program and erase operations.
by requiring only two write cycles to program data
instead of four.
Device erasure occurs by executing the erase com-
mand sequence. This initiates the
Embedded Erase
algorithm—an internal algorithm that automatically
preprograms the array (if it is not already pro-
grammed) before executing the erase operation.
During erase, the device automatically times the
erase pulse widths and verifies proper cell margin.
The host system can detect whether a program or
erase operation is complete by observing the RY/BY#
pin, or by reading the DQ7 (Data# Polling) and DQ6
(toggle)
status bits.
After a program or erase cycle
has been completed, the device automatically re-
turns to reading array data.
The
sector erase architecture
allows memory sec-
tors to be erased and reprogrammed wi thout
affecting the data contents of other sectors. The de-
vice is fully erased when shipped from the factory.
Hardware data protection
measures include a low
V
CC
detector that automatically inhibits write opera-
tions during power transitions. The
hardware
sector protection
feature disables both program
and erase operations in any combination of the sec-
tors of memory. This can be achieved in-system or
via programming equipment.
The
Erase Suspend
feature enables the user to put
erase on hold for any period of time to read data
from, or program data to, any sector within that
bank that is not selected for erasure. True back-
ground erase can thus be achieved. There is no need
to suspend the erase operation if the read data is in
the other bank.
The
hardware RESET# pin
terminates any opera-
tion in progress and resets the internal state
machine to reading array data. The RESET# pin may
be tied to the system reset circuitry. A system reset
would thus also reset the device to reading array
data, enabling the system microprocessor to read
the boot-up firmware from the Flash memory.
The device offers two power-saving features. When
addresses have been stable for a specified amount of
time, the device enters the
automatic sleep mode.
The system can also place the device into the
standby mode.
Power consumption is greatly re-
duced in both these modes.
AMD’s Flash technology combines years of Flash
memory manufacturing experience to produce the
hi ghe st l evels of qua lity, rel iabi lity, and cost
effectiveness. The device electrically erases all bits
within a sector simultaneously via Fowler-Nordheim
tunneling. The bytes are programmed one byte or
word at a time using hot electron injection.
Simultaneous Read/Write Operations with
Zero Latency
The Simultaneous Read/Write architecture provides
simultaneous operation
by dividing the memory
space into two banks. Bank 1 contains boot/parame-
ter sectors, and Bank 2 consists of larger, code
sectors of uniform size. The device can improve
overall system performance by allowing a host sys-
tem to program or erase in one bank, then
immediately and simultaneously read from the other
bank, with
zero latency.
This releases the system
from waiting for the completion of program or erase
operations.
Am29DL400B Features
The device offers complete compatibility with the
JEDEC single-power-supply Flash command set
standard.
Commands are written to the command
register using standard microprocessor write tim-
ings. Register contents serve as input to an internal
state machine that controls the erase and program-
ming circuitry. Write cycles also internally latch
addresses and data needed for the programming and
erase operations. Reading data out of the device is
similar to reading from other Flash or EPROM
devices.
Device programming occurs by executing the pro-
g ra m c o m m a n d s e q u e n c e . T h i s i n i t i a t e s t h e
Chip function: induce PD charger to output maximum power, support maximum induced voltage of 20V. Supported protocols: mainstream fast charging protocols such as PD/QCChip package: ESSOP10
Chip applic...
Question: I want to make a class AB amplifier for use in cars, but I don't know what chips TI recommends. I also want the best sound quality. Please provide relevant typical circuit diagrams and PCB l...
It has been several years since I graduated with a degree in measurement and control, but I still haven't found my life direction. I was in a daze from the beginning to the end. When I heard that some...
I have attached a video. I don’t know if you can watch it.
I'm worried that this section will die.This content is originally created by EEWORLD forum user 1399866558. If you want to reprint or use it ...
Recently, the Guizhou Power Grid Company issued the "Digital Transformation and Construction Implementation Plan" (hereinafter referred to as the "Plan"), proposing to deeply apply cloud-based Inte...[Details]
In April this year, BYD Auto announced that in accordance with its strategic development needs, it would stop the production of fuel vehicles from March 2022. Officials said that in the future, BYD w...[Details]
According to the latest report from Reuters, Nvidia sought EU approval for its acquisition of British chip developer ARM on Wednesday (8th). The European Commission has set October 13 as the initial ...[Details]
Pandemic-driven growth is coming to an end, but the overall market remains robust Preliminary statistics from Gartner, a leading global information technology research and consulting company, show...[Details]
On December 16, ZTE recently released the "5G Millimeter Wave (mmWave) Technology White Paper" (hereinafter referred to as the White Paper). This is another sharing on the application of millimeter w...[Details]
Desuo Precision Industry Engineers pointed out that the high-voltage wiring harness of new energy vehicles is a key component of the high-voltage electrical system, which provides a guarantee for t...[Details]
Shanghai , China – October 18 , 2023 – IAR , the global leader in embedded development software and services, announced today that it has reached an ecological cooperation with Zhongkexin Int...[Details]
In the design of electronic systems, in order to avoid detours and save time, the requirements for anti-interference should be fully considered and met, and anti-interference remedial measures shou...[Details]
Apple today announced that the App Store now offers search suggestions, a new feature designed to make it easier to find what you're looking for when you're looking for new apps or games. Users will ...[Details]
Supercars, a symbol of speed and passion, have long surpassed the definition of a simple means of transportation. They represent unparalleled performance - strong power, lightning speed and excelle...[Details]
This program simply demonstrates how to use the EERPOM of ATMEGA16. Introduction to EEPROM Write operation of EEPROM Read operation of EEPROM In order to simplify the program, various data are not ...[Details]
On February 23, the industry's analog giant Texas Instruments (TI) announced the appointment of Jiang Han as TI's vice president and president of China. The whereabouts of Ms. Sandy Hu, former vice p...[Details]
Shanghai, China, October 7, 2023 – VIAVI Solutions (VIAVI) recently announced that it has become one of three consortiums to win financial support in the Open Network Ecosystem (ONE) competition host...[Details]
According to tomshardware, Taiwanese officials said at a press conference that as TSMC expands into the United States, they will deploy a special team to protect TSMC’s technology and business secre...[Details]
Do you want to achieve local consumption of renewable energy? Do you want to improve your energy efficiency?
Are you worried about the high energy costs? Don't worry! We have a super tool that...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
