Ordering number : ENN7196A
SGF33
N-Channel GaAs MESFET
SGF33
For C to Ku-Band Local Oscillator and Amplifier
Features
•
•
•
•
Package Dimensions
unit : mm
1316
[SGF33]
(Bottom view)
(Side view)
Low phase noise.
Highly reliable protection film.
Automatic surface mounting supported.
MCPH4 package.
0.25
0.3
3
4
0.15
2.1
1.6
0.25
1.3
2.0
0.07
2
1
(Top view)
4
(Side view)
3
1 : Gate
2 : Source
3 : Drain
4 : Source
SANYO : MCPH4
Specifications
Absolute Maximum Ratings
at Ta=25°C
Parameter
Drain-to-Source Voltage
Gate-to-Source Voltage
Drain Current
Allowable Power Dissipation
Junction Temperature
Storage Temperature
Symbol
VDS
VGS
ID
PD
Tj
Tstg
Mounted on copper foil (area : 0.96mm )
Glass epoxy board (145!80!1.6mm)
150
--55 to +150
°C
°C
2
Conditions
0.85
1
2
Ratings
6
--5
100
400
Unit
V
V
mA
mW
Electrical Characteristics
at Ta=25°C
Parameter
Gate-to-Source Leakage Current
Saturated Drain Current
Cutoff Voltage
Forward Transfer Admittance
Symbol
IGSO
IDSS
VGS(off)
yfs
Conditions
VGS=--5V
VDS=3V, VGS=0
VDS=3V, ID=100µA
VDS=3V, ID=10mA
Ratings
min
30
--0.5
typ
50
--1.6
34
max
--10
70
--2.7
Unit
µA
mA
V
mS
Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft's
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
62003 TS IM TA-100632 / 13003 TS IM TA-3556 No.7196-1/5
SGF33
Amplification Characteristics Measured by the DUT
Pout -- Pin
f=11GHz
VDS=3V
ID=30mA
GLP=5.7dB
P1dB=15.7dBm
=
B)
5.7
18
15
Output Power, Pout(dBm)
(d
LP
G
4.7
10
5
0
--5
0
5
10
15
IT04380
Input Power, Pin(dBm)
Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customer's
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customer's products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products(including technical data,services) described or
contained herein are controlled under any of applicable local export control laws and regulations,
such products must not be expor ted without obtaining the expor t license from the authorities
concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co., Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification"
for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.
This catalog provides information as of June, 2003. Specifications and information herein are subject
to change without notice.
PS No.7196-5/5
京公网安备 11010802033920号
EEWORLD
