REVISION S
DESIGNED & DIMENSIONED
IN MILLIMETERS[INCHES]
3.00 .118
REF
PCIEC-098-XXXX-EC-EM-X SHOWN
OVERALL LENGTH: XXXX + "L" REF (SEE TABLE 3)
IDC LENGTH: XX.XX+3.17[.125] 1%
RED STRIPE
TO THIS SIDE
FIG 1
PCIEC-XXX-XXXX-XX-XX-X-XX
No OF POSITIONS
-036: 36 POSITIONS (X1)
-064: 64 POSITIONS (X4)
-098: 98 POSITIONS (X8)
-164: 164 POSITIONS (X16)
LENGTH
0050 mm MIN.
(SEE NOTE 11)
IMPEDANCE
-85: 85 ohm
(LEAVE BLANK FOR 100 ohm)
CABLE OPTIONS
-P: EYESPEED-CABLE AND POWER LINES
*
-A: ACCELERATE CABLE NO POWER
LINES
-AP: ACCELERATE CABLE AND POWER
*
LINES
(LEAVE BLANK FOR EYESPEED CABLE
AND NO POWER LINES) (SEE TABLE 4)
(SEE NOTE 9)
SECOND END
-EC: PCIE EDGE CARD
-EM: PCIEC EDGE MOUNT
CONNECTOR
(SEE TABLE 4)
FIRST END
-EC: EDGE CARD
(SEE TABLE 4)
"A"
REF
* NOT RELEASED
LENGTH: XXXX ± 1%
25.40 1.000
REF
1.57 .062
REF
C1
36.45 1.435 REF
"B"
REF
8.70 .343
REF
ACCELERATE CABLE
HDRL-11
(SEE NOTE 5)
EYESPEED CABLE
NOTES:
ENDS OF CABLE TO BE
POTTED WITH UV EPOXY
ENDS OF CABLE TO BE
POTTED WITH UV EPOXY
FOR 85 OHM OPTION
"85" WILL BE SHOWN
IN THIS REGION
11.05 .435
REF
1.
C
REPRESENTS A CRITICAL DIMENSION.
2. SUB-TTF LENGTH IS EQUAL TO PCIEC LENGTH.
C2 3. ALL ASSEMBLIES TO BE 100% ELECTRICALLY TESTED
FOR SHORTS AND OPENS.
C3 4. ALL ASSEMBLIES TO BE 100% HI-POT TESTED AT 300V.
5. TOP SUB-TTF NOT SHOWN IN THIS VIEW FOR CLARITY; HDRL-11
TO BE CENTERED ON LOWER SUB-TTF AS SHOWN; HDRL-11 IS
TO CONTAIN PART NUMBER, SHOP NUMBER, & DATE CODE.
6. FOR SUB-ASSEMBLY AND FINISHED GOOD PACKAGING
REQUIREMENTS, REFERENCE PACKAGING STANDARD
CO-HD-WI-3033-M.
7. FOR PRE-TINNING PROCESS INFORMATION ON THE SUB-
PCB'S, SEE TRAVELER SUB-PCIEC-XXX-EC-XX AND SUB-PCIEC-
XXX-EM-XX. FOR -85 OHM OPTION SEE TRAVELER SUB-PCIEC-
XXX-EC-XX-85 AND SUB-PCIEC-XXX-EM-XX-85.
8. KEY CONSUMES 3 PITCHES.
9. NO POWER LINES CREATES A NO CONNECT CONDITION AT
POSITIONS B1, B2, B3, B8, A2, A3, A9 AND A10
10. HOT PLUG DETECT COMMON AND ONLY FIRST AND LAST
USED ON EACH POSITION.
11. CABLE LENGTHS LONGER THAN 1015 MILLIMETERS ARE NOT
SUPPORTED BY S.I. TEST DATA.
12. SIGNAL MAPPING IS ONLY AVAILABLE IN A 1-TO-1
CONFIGURATION. FOR EXAMPLE A1 TO A1, A2 TO A2, ETC.
Pb
THIS PRODUCT MANUFACTURED
WITH LEAD-FREE PROCESSING
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN MILLIMETERS.
TOLERANCES ARE:
DECIMALS
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
.X: 0.3 [.01]
2
.XX: 0.13 [.005]
.XXX: 0.051 [.0020]
ANGLES
MATERIAL:
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
PCIEC CABLE ASSEMBLY
PCIEC-XXX-XXXX-XX-XX-X-XX
F:\DWG\MISC\MKTG\PCIEC-XXX-XXXX-XX-XX-X-XX-MKT.SLDDRW
BY:
D FRALEY
08/24/2006
SHEET
1
OF
2
REVISION S
A1
FIRST END - EDGE (SEE TABLE 4)
B1
AX
BX
-EC
SECOND END - EDGE (SEE TABLE 4)
B1
A1
BX
AX
-EM
A1
B1
*SEE NOTES 9, 10 & 12
AX
BX
-EC
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail info@SAMTEC.com
code 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
SHEET SCALE: 1:2
PCIEC CABLE ASSEMBLY
08/24/2006
SHEET
2
OF
2
PCIEC-XXX-XXXX-XX-XX-X-XX
BY:
D FRALEY
F:\DWG\MISC\MKTG\PCIEC-XXX-XXXX-XX-XX-X-XX-MKT.SLDDRW
京公网安备 11010802033920号
EEWORLD
