3
Instructions for Assembly of Mini D Ribbon
(MDR) Non-Shielded Plugs 101XX-8000
Description
The tools listed are required to assemble the 3M MDR
8000 IDC Wiremount non-shielded plug. These plugs can
be installed as terminal end connectors or in daisy chains.
Note:
3M studies have shown a 30 AWG Solid Conductor Cable
is the preferred cable to terminate to the MDR 101XX-8000
series plug.
Assembly press
Locator plate
Platen
Height Gauge
Width Gauge (XX position)
Cable Stopper (XX position)
3640 or 10985
10980-3
10981-5
10982-4
10983-XX
10984-XX
Tool Setup
1
2
3
10982-4
Height Gauge
Width Gauge
Cable Guides
1
2
3
Place the 10982-4 height gauge on the
base plate of the press (locator plate
removed). Bring the handle down fully
and adjust the shaft to touch the gauge.
Raise the handle, remove the gauge then
turn the adjustment screw one quarter turn
(90 degrees) clockwise.
Adjust the width of the cable guides on
the 10980-3 locator plate to correspond to
the connector. Use width gauge 10983-
XX for connectors having XX positions.
Remove the width gauge when finished.
Install the 10981-5 platen and the locator
plate on the press.
Connector Assembly
1
Connector Body
2
Cable
Stopper
Cable
Connector
Cover
3
4
5
6
Remove the protective paper lining from
the connector cover.
Place the connector cover, then the cable
then the connector body on the locator plate.
Note:
The locator plate is shown removed
from the press for clarity.
When installing a plug on the end of a
cable, use the cable stopper to correctly
position the cable.
Note:
The locator plate is shown removed
from the press for clarity.
4
5
7
8
Lower the press handle to assemble the
connector. It is recommended to check
the tool setup before starting each
production run. Proper seating of the
connector cover onto the connector body
can be checked by measuring the height of
the connector/cover assembly.
The 101XX-8000 plug may be assembled
with a strain relief that is installed on the
topside of the plug. Bend cable over the
top of the connector and snap both inside
and outside latches into the body.
For technical, sales or order information, please contact 3M at:
Phone: 1-800-225-5373 Fax: 1-800-325-5329
Important Notice
All statements, technical information and recommendations related to
the Seller’s products are based on information believed to be reliable, but
the accuracy or completeness thereof is not guaranteed. Before utilizing the
product, the user should determine the suitability of the product for
its intended use. The user assumes all risks and liability whatsoever in
connection with such use.
Any statements or recommendations of the Seller which are not contained
in the Seller’s current publications shall have no force or effect unless
contained in an agreement signed by an authorized officer of the Seller.
The statements contained herein are made in lieu of all warranties, expressed
or implied, including but not limited to the implied warranties of merchantability
and fitness for a particular purpose which warranties are hereby expressly
disclaimed.
SELLER SHALL NOT BE LIABLE TO THE USER OR ANY OTHER PERSON
UNDER ANY LEGAL THEORY, INCLUDING BUT NOT LIMITED TO
NEGLIGENCE OR STRICT LIABILITY, FOR ANY INJURY OR FOR ANY
DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES
SUSTAINED OR INCURRED BY REASON OF THE USE OF ANY OF THE
SELLER’S PRODUCTS.
3
Electronic Products Division
6801 River Place Blvd.
Austin, TX 78726-9000
http://www.3m.com/interconnects
Recycled Paper
40% Pre-consumer waste paper
10% Post-consumer waste paper
Litho in USA
© 3M 1998 34-7045-3910-4(0881.0)JHA/TG
京公网安备 11010802033920号
EEWORLD
