The 3M Locator Plate 3443-106N is designed to aid in
the assembly of the preassembled and two-piece 3M
™
Delta Connector and pin 9 through 37 position
connectors. End-to-end, as well as daisy chain
assemblies, can be made. Set-up and assembly
instructions are based on termination procedures with
the 3M manual and pneumatic presses.
Locator Plate Includes
• Instruction sheet
• One mounting screw
• Mounting studs for cable guides
Note:
For the one-piece preassembled connector,
all locator plate part options are listed on
the last page of the assembly instructions.
Tool Preparation
Shut Height Setting
Connector
3640
3316
82XX
83XX
21
21
Assembly Press
3335
3339-1
21.5
21.5
3830
Self-Adjusting
Adjust the shut height setting before installing the Locator Plate and Platen using the 3M™ Shut
Height Gauge 3436-1.
PIN
D
A
F
B
E
C
Note:
If the staging platform (optional) is used, please refer to that instruction sheet for mounting
instructions.
78-8133-3685-2-A
2
Preassembled Connector Assembly Procedure
Set-up
1. Adjust the end block according to the flange style and connector size.
A
Thru-hole style:
Rotate the end block so that the locating pin is facing the inside of the locator plate.
The pin has to be removed so that the end block can be rotated. Then reassemble the pin. The pin is
used to guide the platen during harness assembly.
B
Floating bushing and threaded insert style:
Rotate the end block so that the locating pin is facing the outside of the locator plate.
2. Install the cable stop insert 3664-B.
C
3. Install the cable guide on the mounting stud. Refer to the last page for the appropriate guide.
D
4. Place the locator plate on the press and affix it using the locking screw provided.
5. Place the platen on the assembly press. Refer to the last page for the appropriate platen.
Assembly
1. Cut required cable length using one of the 3M cutting tools.
2. Remove the connector from the packing strip.
3. Slide the connector onto the guiding groove and into the end block.
E
4. Slide the cable under the cable guide. If the cable should not enter into the connector smoothly, check the
flatness of the cable.
F
5. Complete the assembly by bringing the press handle to the full downward position.
6. Raise the press handle and cable guide, then remove completed assembly.
7
Visually inspect to insure that:
a. The cover is fully seated. If not, check the shut height setting.
b. The cable is correctly aligned in the cover. If not, check end guide adjustment.
Two-Piece Connector Assembly Procedure
Set-up
1. Follow steps 1, 4 and 5 of the preassembled set-up instructions.
Assembly
1. Grasp 3M
™
Delta Cover Strip between thumb and forefinger. While holding the adjacent cover, pull laterally
away from strip leaving the adhesive with a smooth clean edge.
2. Press cable ribs into cover alignment grooves.
3. Visually inspect to insure that the cable is properly aligned and oriented into cover grooves.
4. Engage cable/cover subassembly with connector body. Place subassembly in the locator plate with the
connector body facing up.
5. Complete the assembly by bringing the press handle to the full downward position.
6. Raise the press handle and remove the completed assembly.
7. Visually inspect to insure that:
a. The cover is fully seated. If not, check the shut height setting.
b. The cable is correctly aligned in the cover. If not, check end guide adjustment.
3
78-8133-3685-2-A
Standard Two-Piece Connector
The 3M
™
Locator Plate 3443-106N and the Platen listed below is all that is needed for the assembly of the
standard two-piece connector.
Connector
Number
8209
8309
8215
8315
8225
8325
8237
8337
Locator
Plate
3443-106N
3443-106N
3443-106N
3443-106N
3443-106N
3443-106N
3443-106N
3443-106N
Platen
3442-39N
3442-9
3442-39N
3442-9
3442-41N
3442-9
3442-41N
3442-9
Cable Guide
3664-09
3664-09
3664-15
3664-15
3664-25
3664-25
3664-37
3664-37
Cable Stop
Open Cover
3664-B
3664-B
3664-B
3664-B
3664-B
3664-B
3664-B
3664-B
Cable Stop
Closed Cover
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Note:
Replacement studs are available for the cable guides, part number 3664-C. Optional End Block,
3664-A, for connectors with floating bushings and threaded inserts is also available.
CAUTION
The 82XX series connector must use the 3M™ 3442-39N Platen. The
3442-39N platen has three blade-like protrusions on the surface of the
platen. These blades must fit inside the metal shell of the connector and
the connector pins must fit in the grooves between the blades when the
platen engages the connector. Make sure that there is good alignment
between the connector and the platen to assure that the shell or pins of
the connector are not damaged during termination.
3M is a trademark of 3M.
IMPORTANT NOTICE
Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for one year from the date of
purchase.
3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
If this product is defective within the warranty period stated above, your
exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product.
Except where prohibited
by law, 3M will not be liable for any loss or damage arising from this 3M product, whether direct, indirect, special, incidental or consequential
#inI am using 2 8421 coding switches and stc15w201s to make a 9.9 second delay switch. The following program does not work properly. Please give me your advice.
#includereg52.h
sbit timeup = P1^4; //D...
Last week, Espressif announced the launch of the low-power, low-cost ESP32-C2 chip, which is smaller in size and more powerful than the ESP8266. On the basis of meeting the needs of simple IoT applica...
TrueStudio flashes STM32 project and prompts Verify failed. Now I am helpless.
Compilation is OK, debug is burned to stm32103c8t6, it was normal before, burning other small projects is also normal,but...
This dynamic Near Field Communication (NFC) tag design outlines the required components and layout considerations, and provides firmware examples to illustrate how to implement NFC into applications s...
[i=s]This post was last edited by cxmin on 2019-6-21 10:48[/i]In daily life, people often cannot stay away from the influence of radioactive radiation, such as going to the hospital for CT scans. Espe...
1. Compilation feedback and optimizationThe TIC6000 compiler can optimize the code in various ways to increase the execution speed and reduce the size of the code. These optimizations include simplify...
When expanding a microcontroller, the expansion of program memory and data memory must be considered separately.
Memory is the most commonly used external expansion chip in the single-chip microcompu...[Details]
In order to facilitate the centralized control of distributed field measurement and control equipment, fieldbus technology has been widely used. RS485 bus has become one of the most widely used fie...[Details]
A frequency source circuit is designed, which controls the DDS chip AD9911 by the single-chip microcomputer PIC18LF4520. The software and hardware implementation methods of the single-chip microcompu...[Details]
Infineon Technologies AG recently announced the addition of new industrial standard packaging products to its CoolSiC 1200 V and 2000 V MOSFET module series. It adopts the mature 62 mm device half-b...[Details]
Resistors are generally called resistors in daily life. It is a current limiting element. After the resistor is connected to the circuit, the resistance of the resistor is fixed. Generally, it has ...[Details]
Apple's 2021 spring conference was held as scheduled at 1 a.m. Beijing time on April 21. Cook announced at the online conference that starting from April 30, iPhone 12 and iPhone 12 mini will launch ...[Details]
Recently, the national finals of the "Core Innovation Cup" Future Car Human-Computer Interaction Design Competition for Colleges and Universities came to a successful conclusion at the 2019 Intellige...[Details]
The interference generated by the switching power supply can be divided into two types according to the type of noise interference source: peak interference and harmonic interference. If it is divid...[Details]
01 Analysis of the internal structure of the microcontroller Let's think about a problem. When we write an instruction into the microcontroller in the programmer, and then remove the microcontroller,...[Details]
Autonomous driving path planning
As we all know, unmanned driving can be roughly divided into three aspects: perception, decision-making and control. Path planning is the decision-making stage...[Details]
This article discusses the precise control of LED constant current drive, and describes the differences between different drives in different applications, including the introduction of distributed co...[Details]
New energy vehicles are being promoted rapidly in Europe, but the shortage of power batteries in Europe has led to a "crying out" for new energy vehicles in Europe. Europe has huge demand for power...[Details]
On October 6, Volkswagen Group officially announced that its joint venture battery materials company will be named IONWAY. The company is jointly established by PowerCo, a battery business company o...[Details]
Preface
The automotive industry is currently at a very challenging historical moment. With the ever-changing application scenarios such as electrification, intelligence, networking and sharing...[Details]
51mcu
京公网安备 11010802033920号
EEWORLD
