Circuit diagrams and other information relating to SMSC products are included as a means of illustrating typical applications. Consequently, complete information
sufficient for construction purposes is not necessarily given. Although the information has been checked and is believed to be accurate, no responsibility is
assumed for inaccuracies. SMSC reserves the right to make changes to specifications and product descriptions at any time without notice. Contact your local
SMSC sales office to obtain the latest specifications before placing your product order. The provision of this information does not convey to the purchaser of the
described semiconductor devices any licenses under any patent rights or other intellectual property rights of SMSC or others. All sales are expressly conditional
on your agreement to the terms and conditions of the most recently dated version of SMSC's standard Terms of Sale Agreement dated before the date of your
order (the "Terms of Sale Agreement"). The product may contain design defects or errors known as anomalies which may cause the product's functions to deviate
from published specifications. Anomaly sheets are available upon request. SMSC products are not designed, intended, authorized or warranted for use in any life
support or other application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without prior
written approval of an Officer of SMSC and further testing and/or modification will be fully at the risk of the customer. Copies of this document or other SMSC
literature, as well as the Terms of Sale Agreement, may be obtained by visiting SMSC’s website at http://www.smsc.com. SMSC is a registered trademark of
Standard Microsystems Corporation (“SMSC”). Product names and company names are the trademarks of their respective holders.
SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED WARRANTIES OF MERCHANTABILITY,
FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE, AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE
OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL
DAMAGES; OR FOR LOST DATA, PROFITS, SAVINGS OR REVENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT;
TORT; NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY OF BUYER IS HELD
TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Revision 1.1 (06-12-06)
DATASHEET
ii
SMSC EMC1203/EMC1204
Triple/Quad Single-Wire Temp Sensor in MSOP-8 Using SMSC BudgetBus
TM
Sensor Interface
Datasheet
Chapter 1 Pin Configuration
DP1
DN1
DN2/DP3
DP2/DN3
1
8
VDD
GND
SCLK
BBUS
2
EMC1203/
7
EMC1204
3
TOP VIEW
6
4
5
Figure 1.1 EMC1203 and EMC1204 Pin Configuration
1.1
Pin Description
Table 1.1 EMC1203 and EMC1204 Pin Description
PIN
DP1
DN1
DN2/DP3
DP2/DN3
BBUS
SCLK
GND
VDD
PIN NO.
1
2
3
4
5
6
7
8
DESCRIPTION
Positive Analog Connection to External Temperature Diode 1
Negative Analog Connection to External Temperature Diode 1
Negative Analog Connection to External Temperature Diode 2
Positve Analog Connection to External Temperature Diode 3, EMC1204 only
Positve Analog Connection to External Temperature Diode 2
Negative Analog Connection to External Temperature Diode 3, EMC1204 only
Serial Bus Interface to BBUS Host
Normally GND, this pin may be configured to source a synchronous clock.
Ground
Supply Voltage V
DD
SMSC EMC1203/EMC1204
DATASHEET
1
Revision 1.1 (06-12-06)
Triple/Quad Single-Wire Temp Sensor in MSOP-8 Using SMSC BudgetBus
TM
Sensor Interface
Datasheet
1.2
Absolute Maximum Ratings
Table 1.2 EMC1203 and EMC1204 Maximum Ratings
DESCRIPTION
RATING
-0.3 to 5.0
-0.3 to V
DD
+0.3
0 to 85
-55 to 150
Refer to JEDEC
Spec. J-STD-020
UNIT
V
V
°C
°C
Supply Voltage V
DD
Voltage on any other pin
Operating Temperature Range
Storage Temperature Range
Lead Temperature Range
Package Thermal Characteristics for MSOP-8
Power Dissipation
Thermal Resistance(at 0 air flow)
ESD Rating, All Pins Human Body Model
TBD
109.6
2000
°C/W
V
Note:
Stresses above those listed could cause damage to the device. This is a stress rating only
and functional operation of the device at any other condition above those indicated in the
operation sections of this specification is not implied. When powering this device from
laboratory or system power supplies, it is important that the Absolute Maximum Ratings not be
exceeded or device failure can result. Some power supplies exhibit voltage spikes on their
outputs when the AC power is switched on or off. In addition, voltage transients on the AC
power line may appear on the DC output. If this possibility exists, it is suggested that a clamp
circuit be used.
Revision 1.1 (06-12-06)
DATASHEET
2
SMSC EMC1203/EMC1204
Triple/Quad Single-Wire Temp Sensor in MSOP-8 Using SMSC BudgetBus
京公网安备 11010802033920号
EEWORLD
