STANDARD
Resistive Touch Panel Specification
554 4-Wire Series
RoHS compliant
Input Panel
Panel Drive
change
over switch
Noise
Filter
n
FEATURES
•
Superior quality standard 4 wire resistive analog touch panel
•
Excellent specification and high quality
- Anti Newton ring technology
- High reliability materials
•
Pen/finger type
•
Transparency - 80% typical
•
RoHS compliant
n
PART NUMBERS
Touch Panels:
Part Number
Size
T010-1201-T200
17.0”
N010-0554-T902 15.0”
N010-0554-T813 12.1”
N010-0554-T814 12.1”
N010-0554-T805 12.1”
N010-0554-T351 10.4”
N010-0554-T352 10.4”
N010-0554-T347 10.4”
N010-0516-T104
N010-0519-T742
N010-0554-T504
N010-0554-T511
N010-0516-T947
N010-0514-T101
10.4”
8.4”
8.4”
8.4”
8.1”
7.0”
MCU
Control
Section
A/D con-
verter
Interface
Type
Pen/Finger
Pen/Finger
Pen/Finger
(AS, DPET)
Pen/Finger
Pen/Finger
Pen/Finger
(86%, AS)
Pen/Finger
(82%, AS)
Pen/Finger
Pen/Finger
(86%, Clear)
Pen/Finger
(86% Clear)
Pen/Finger
(0.7mm glass)
Pen/Finger
(1.1mm glass)
Pen/Finger
(1.1mm glass)
Pen/Finger
(W 16:9, Auto-
motive, 82%, AS, 50mm tail)
Part Number
T010-1301-T320
N010-0514-T003
N010-0514-T005
T010-1301-T350
N010-0518-T342
N010-0554-T048
N010-0554-T043
N010-0554-T009
N010-0554-T015
N010-0554-T241
N010-0556-T408
N010-0554-T703
N010-0516-T407
Size
7.0”
Type
Pen/Finger
(82%, AS)
82%, AS)
88%, AS)
6.5” Pen/Finger
(W 16:9, Automotive,
6.5” Pen/Finger
(W 16:9, Automotive,
6.5”
6.4”
6.4”
6.4”
5.7”
5.7”
4.3”
3.9”
3.8”
3.7”
Pen/Finger
(W 16:9)
Pen/Finger
(78% polarized)
Pen/Finger
(86% clear)
Pen/Finger
(80%, AG)
Pen/Finger
Pen/Finger
Pen Finger
(86%, AS, DPET)
Pen/Finger
(86% Clear)
Pen/Finger
Pen/Finger
(0.7mm glass)
n
PART NUMBERS
Controller Boards:
Part Number
N16B-0558-B270
N16B-0558-B730
Type
4-Wire, RS232
4-Wire, USB
n
PART NUMBERS
Interface Controller Chips:
Part Number
N010-0559-V036
NC41120-0018
Type
4-Wire, RS232
4-Wire, USB
554 SERIES
n
DIMENSION EXAMPLE (10.4” SHOWN)
(8.00)
(8.70)
9.50 Anti-input area
(10.00)
228.20
216.20: Transparent area
214.80: Boundary line of the top enclosure
213.20
212.20: Guaranteed active area
112.10
8.00
7.50
87.70
159.40: Guaranteed Active Area
160.40
8.00
7.50 Anti-
input area
6.70
162.00: Boundary Line of top enclosure
4.00
4.70
5.50 Anti-input area
6.00
5.40
164.60: Transparent Area
175.40
Top
87.70±0.1
5.00±0.5
#4
4.00
10.20
26.50
#1
15.00
Left
Right
75.00±1.0
6.70
n
DETAILED SPECIFICATION
n
1.0 APPLICATION
This specification applies to the standard FID-554 seriesTouch Panel (Pen/Finger type).
n
2.0 ADDITIONAL APPLICATIONS
Complete specification document is available upon request for customers with whom we have an approved
NDA in place.
n
3.0 DESCRIPTION AND BLOCK DIAGRAM
This panel in combination with a control IC chip is used to transfer the co-ordinates of the touched position to
the host system (see block diagram above).
n
4.0 DRAWING
(Please
see the diagram above.)
Definitions of the major dimensions indicated on this diagram:
Effective Input Area (A)
Area guaranteed to meet all the
characteristics detailed in this specification
Anti-input Area (C)
An insulating area allowed to protect
the touch panel from giving false
readings when an enclosure touches
the panel. (See fixing instructions)
n
5.0 CHARACTERISTICS
n
5.1 MECHANICAL
Operating Force
5.40
Bottom
Unit: mm
A
B
C
Force
0.05~0.49 N (5 ~ 50gF) Measured with
a Silicon Measurement Rod R 8
(Round type 8mm) Silicon Rubber
Hardness 60˚C
Pencil hardness 3H minimum against
specification JIS K-5400
Silicon Rubber Rod
78% min. measured in the effective input area to JIS K 7105 using a
MURAKAMI SHIKISAI KENKYUSHO type IIR 100 meter.
5% type measured in the effective input area using a MURAKAMI
SHIKISAI KENKYUSHO type IIR 100 meter with an Anti Glare treated
2
Hardness of Surface
n
5.2 OPTICAL
Transparency
Haze
554 SERIES
n
5.3 ELECTRICAL
Rated Voltage:
Resistance X axis:
Resistance Y axis:
Switch Bounce (Chattering):
Insulation resistance:
Dielectric Strength:
Linearity:
DC 7V max.
300 to 850 Ω (at the connector)
100 to 600 Ω (at the connector)
20ms min when using the silicon rubber measurement rod
10MΩ minimum at 25KV DC
No problems when at 25KV DC for 1 minute
2% max.
Co-ordinate Point
Note 1:
Measurement condition of linearity is corrected within the
control IC. In general the location accuracy is specified
as follows:
Actual co-ordinate point - theoretical co-ordinate point
= location accuracy.
In general a 9 point co-ordinate calibration system is used
to adjust the micro controller accuracy. (20 point can be
used in combination with an EEPROM design).
Theoretical
Error
Actual
Distance
n
5.4 ENVIRONMENTAL
-5˚C to 60˚C
-20˚C to 70˚C
20% to 85% RH with a Maximum wet bulb temperature of 38˚C
10% to 90% RH with a Maximum wet bulb temperature of 38˚C
Coating with the following chemicals and storing at room temperature for 2
hours gives no problems. 10% NaCl-water solution, ethyl-acetate, ethyl-
alcohol, toluene, methyl-ethyl-ketone
No issues down to 0.5 x Normal Air pressure
Operating Temperature (*):
Storage Temperature:
Operating Humidity:
Storage Humidity:
Chemical Resistance:
Low Air Pressure:
n
5.5 PEN LIFE
Note taking life:
100,000 words minimum
Input life :
1,000,000 times minimum
Note 1:
Words are written in the notes area and the size of the word is
7.5mm x 6.75mm. A word is any Alphabet / Number / Mark.
The pen is as shown below and applies a force of 250g.
A failure is judged to happen when the current consumption or
insulation resistance or dielectric strength are not met as
shown in 5.3. The location accuracy with 9 point calibration
must be ±4.4 mm max.
Effective input area
Notes
9 mm
10mm
8
ø6.0
ø2.0
3.5
110.0±1.0
3.0
ø2.
0.
1.0
1.5
ø 4.6
R
9.0
0
3
554 SERIES
n
5.6 FINGER LIFE
A finger is simulated by a silicon rubber plunger
R8 (Round type 8mm size) hardness 60˚C at 200g
at frequency 5Hz.
A failure is judged to happen when the current
consumption or insulation resistance or dielectric
strength are not met as shown in 5.3. The location
accuracy with 9 point calibration must be ±4.4 mm max.
Operating force is 150g max.
n
5.7 INFORMATION ON THE PANEL
Production year 99 00 etc.
9 0 1
0 1 2
[ . . . .
[ . . . . .
. . . . . . .]
. . . . . . ]
The left side number shows production year, eg 1999
The left side number shows production year, eg 2000
The first dot after the space shows production month, eg May
The first dot after the space shows production month, eg June
n
6 PACKAGING
n
6.1 PACKING SPECIFICATION
Vibration:
10~55 Hz at 1 Octave per minute 10G 20 cycles with one side 0.75mm
Drop test:
60cm Drop 1 corner, 3 crease lines and 6 faces. 1 each 1 time
After the test no glass: flaw or crack is seen, and no dent or scratch on the film.
Also glass and film must not separate.
n
6.1 PACKING DETAILS
Each touch panel is placed into a plastic bag and is
held in place by a slit cut into the side of the card-
board. A second insertion piece is placed into the
carton to again add stability. The qty is written on
the side of the box. For example the N010-0554-
T001 has 80 pieces per box.
Insert
Touch panel with bag
Slit in cardboard
550 Type panel illustrated (554 type packed
a similar way)
4
554 SERIES
n
7.0 REJECT CRITERIA
Description
Film Dent
Reject Criteri a
Area ≥ 0.1mm
2
Area ≥ 0.05mm
2
& area < 0.1mm
2
Area < 0.05mm
2
Area > 0.1mm
2
Area ≥ 0.05mm
2
& area < 0.1mm
2
Area < 0.05mm
2
Area > 0.1mm
Area ≥ 0.03mm & width <0.1mm and length < 10mm
Area < 0.05mm
: to be zero
: to be max. 5 points
: none specified
: to be zero
: to be max. 5 points
: none specified
: to be zero
: to be max. 1 point
: none specified
Foreign
material
between
glass and film
Dot type
Line type
Scratch
Dot blur or hard coat
missing
Newton Ring
Glass flaw
Area ≥ 0.1mm
: to be zero
Area ≥ 0.03mm & width <0.1mm with length < 80mm : to be max. 1 point
Area < 0.03mm & width <0.1mm with length < 30mm : none specified
Area ≥ 0.5mm
2
Area ≥ 0.03mm
2
& area < 0.5mm
2
Area < 0.05mm
2
: to be zero
: to be max. 5 points
: none specified
These must not be seen from Panel film side under a fluorescent lamp (3
wavelength type lamp). Not to be verified form glass side.
To be no flaw which is bigger than that shown in the following diagram. The
number of flaws is not specified.
3mm
5mm
2mm
2mm
n
8.0 GENERAL POINTS OF CAUTION
Touch panels are made of glass, so care must be taken in handling them. Do not stress, pile, bend, lift by
the cable or put any stress on the film, for example moving by film face vacuum. In order to clean wring dry a
cloth which has been emersed in a natural detergent. DO NOT use any organic solvent, acid or alkali solu-
tion. Watch the edge of the panel when cleaning, again for safety reasons.
5
京公网安备 11010802033920号
EEWORLD
