Ultra-compact Pre-wired Photomicrosensor (Non-modulated)
EE-SX95
Meeting Customer Needs with
Ultra-compact Sensors that Mount
with M3 Screws
• Mount using M3 or M2 screws.
• Reliable sensing slot depth of 6.5 mm.
• Indication of sensing window for easy confirmation of
insertion depth.
• Bright indicator for confirmation from many directions.
• Both light-ON and dark-ON outputs provided.
• All models available with either standard cable or
flexible robot cable.
• Load short-circuit protection circuit provided.
Refer to the
Safety Precautions
on
page 5.
For the most recent information on models that have been certified for
safety standards, refer to your OMRON website.
Features
Mount Using M2 or M3 Screws
The EE-SX95 can be mounted using M2 or M3 screws, so it can
easily replace an existing Sensor mounted with M2 screws.
Installation with M2 screws: 18.0
Reliable Best-in-Class Sensing Slot
Depth of 6.5 mm
(Based on April 2013 OMRON investigation.)
A deeper slot helps prevent the sensing object from coming into
contact with the base of the slot, creating greater tolerance in
mechanism design.
6.5mm
Installation with M3 screws: 18.7
Example for the EE-SX950-W
Indication of Sensing Window for Easy
Confirmation of Insertion Depth
The location of the sensing window is indicated on the insertion slot
so that you can visually confirm whether the sensing object covers the
sensing window and easily check the insertion depth.
Bright Indicator for Confirmation from Many
Directions
The bright light indicator can be checked from up to four directions to
enable flexible selection of the installation location.
The sensing object just needs
to extend below this line.
1
EE-SX95
Ordering Information
Sensors
Appearance
Standard
Sensing
method
Sensing
distance
Output
configuration
Connection method
(Cable length)
Pre-wired model with
standard cable (1 m)
Pre-wired model with robot
cable (1 m)
Pre-wired connector model
with robot cable (0.3 m)
L-shaped
Pre-wired model with
standard cable (1 m)
Pre-wired model with robot
cable (1 m)
Pre-wired connector model
with robot cable (0.3 m)
F-shaped
Through-
beam
(with slot)
12
Infrared light
Output
type
NPN
PNP
NPN
NPN
NPN
PNP
NPN
NPN
NPN
PNP
NPN
NPN
NPN
PNP
NPN
NPN
NPN
PNP
NPN
NPN
Model
EE-SX950-W 1M
EE-SX950P-W 1M
EE-SX950-R 1M
EE-SX950-C1J-R 0.3M
EE-SX951-W 1M
EE-SX951P-W 1M
EE-SX951-R 1M
EE-SX951-C1J-R 0.3M
EE-SX952-W 1M
EE-SX952P-W 1M
EE-SX952-R 1M
EE-SX952-C1J-R 0.3M
EE-SX953-W 1M
EE-SX953P-W 1M
EE-SX953-R 1M
EE-SX953-C1J-R 0.3M
EE-SX954-W 1M
EE-SX954P-W 1M
EE-SX954-R 1M
EE-SX954-C1J-R 0.3M
*1
*2
*1
*1
*2
*1
*1
*2
*1
*1
*2
*1
*1
*2
*1
6
23.9
12
12
13.4
12
Pre-wired model with
standard cable (1 m)
11.7
13.4
5 mm
(slot width)
Light-ON
Dark-ON
(2 outputs)
Pre-wired model with robot
cable (1 m)
Pre-wired connector model
with robot cable (0.3 m)
R-shaped
11.7
Pre-wired model with
standard cable (1 m)
Pre-wired model with robot
cable (1 m)
Pre-wired connector model
with robot cable (0.3 m)
13.4
12
U-shaped
Pre-wired model with
standard cable (1 m)
Pre-wired model with robot
cable (1 m)
Pre-wired connector model
with robot cable (0.3 m)
6
13.4
16
*1. A model is available with a 3-m cable. The model number is EE-SX95@-@ 3M.(Example: EE-SX950-W 3M)
*2. A pre-wired model with a PNP output and 1-m robot cable is available. The model number is EE-SX95@P-R 1M.(Example: EE-SX950P-R 1M)
Accessories (Order Separately)
Connector with Robot Cable
Type
Connector with Cable
Cable length
2m
Model
EE-1016-R 2M
Remarks
Connector with lock, AWG26, 4-core Robot Cable
2
EE-SX95
Ratings and Specifications
Type
Pre-wired models
NPN output
Item
PNP output
Standard
EE-SX950-@
L-shaped
EE-SX951-@
F-shaped
EE-SX952-@
R-shaped
EE-SX953-@
U-shaped
EE-SX954-@
Pre-wired
EE-SX950-C1J-R EE-SX951-C1J-R EE-SX952-C1J-R EE-SX953-C1J-R EE-SX954-C1J-R
connector models
Pre-wired models
EE-SX950P-@
5 mm (slot width)
Opaque: 1.8
×
0.8 mm min.
0.025 mm max.
*1
Infrared LED (940 nm)
Light indicator (red LED)
5 to 24 VDC
±10%,
ripple (p-p): 10% max.
15 mA max.
Load power supply voltage: 5 to 24 VDC
Load current: 50 mA max.
OFF current: 0.5 mA max.
50 mA load current with a residual voltage of 0.7 V max.
5 mA load current with a residual voltage of 0.4 V max.
Load short-circuit protection
1 kHz min. (3 kHz average)
*2
1,000 lx max. with fluorescent light on the surface of the receiver
Operating:
−25
to 55°C
Storage:
−30
to 80°C (with no icing or condensation)
Operating: 5% to 85%
Storage:
5% to 95% (with no icing or condensation)
10 to 2,000 Hz (peak acceleration: 150m/s
2
)
with a 0.75-mm single amplitude for 2.5 h (15-min periods, 10 cycles) each in X, Y, and Z directions
500 m/s
2
for 3 times each in X, Y, and Z directions
IEC60529 IP50
Pre-wired models (standard length: 1 m), Pre-wired connector models (standard length: 0.3 m)
Pre-wired models
Approx. 15 g
Pre-wired
Approx. 7 g
connector models
Case/cover
Emitter/receiver
Polybutylene terephthalate (PBT)
Polycarbonate (PC)
EE-SX951P-@
EE-SX952P-@
EE-SX953P-@
EE-SX954P-@
Sensing distance
Standard sensing object
Differential travel
Light source (wave length)
Indicator
Power supply voltage
Current consumption
Control output
Protection circuit
Response frequency
Ambient illumination
Ambient temperature range
Ambient humidity range
Vibration resistance (destruction)
Shock resistance (destruction)
Degree of protection
Connection method
Weight
(packed state)
Materials
*1. The differential travel is the value when a sensing object is moved in a lateral direction to the slot.
*2. The response frequency was measured by detecting the following rotating disk.
Disk
1 mm
2.1 mm
t = 0.2 mm
1 mm
Applicable Connector
Product Connector with Robot Cable
Model EE-1016-R
Appearance
Item
Contact resistance
Insertion strength
Surplus strength
(housing holding strength)
Cable length
Ambient temperature range
Housing
Materials
Contact
25 mΩ max. (at 10 mA DC and 20 mV max.)
20 N max.
15 N min.
2m
−25
to 85°C
Nylon
Phosphor bronze
3
EE-SX95
Engineering Data (Reference Value)
Sensing Position Characteristics
Repeated Sensing Position Charac-
teristics
Dark-ON
Dark-ON
d
Insertion
direction
Dark-ON
Insertion direction
d
d=±0.002
d
Light-ON
0
1
2
3
4
5
6
Distance d (mm)
Light-ON
0
1
2
3
4
5
6
Distance d (mm)
Light-ON
2.92
2.94
2.96
2.98
Distance d (mm)
Vcc = 24 V, No. of repetitions: 20, Ta = 25°C
(Differential travel = 0.025 mm max.)
Note:
The data applies to dark status. Operation may be affected by external light interference or light coming through the sensing object.
I/O Circuit Diagrams
Output
type
Model
Output
transistor
operation
status
Timing charts
Output circuit
EE-SX950-@
EE-SX951-@
EE-SX952-@
EE-SX953-@
NPN EE-SX954-@
output EE-SX950-C1J-R
EE-SX951-C1J-R
EE-SX952-C1J-R
EE-SX953-C1J-R
EE-SX954-C1J-R
OUT1: Light-ON
OUT2: Dark-ON
Light indicator
(red)
(Brown)
1
Load 1
Connector pin
arrangement
for models with
connectors
1
2
Load 2
4
OUT1(Black)
Incident light
No incident light
Main
circuit
2
3
OUT2(White)
5 to
24 VDC
4
Light indicator
ON
(red)
OFF
Output 1
transistor
ON
OFF
(Blue)
3
Load 1 Operate
(e.g., relay) Reset
Output 2
transistor
ON
OFF
Load 2 Operate
(e.g., relay) Reset
EE-SX950P-@
EE-SX951P-@
PNP
EE-SX952P-@
output
EE-SX953P-@
EE-SX954P-@
Light indicator
(red)
(Brown)
OUT1(Black)
Main
circuit
OUT2(White)
Load 1
5 to
24 VDC
Load 2
(Blue)
4
EE-SX95
Safety Precautions
Refer to
Warranty and Limitations of Liability.
WARNING
This product is not designed or rated for ensuring
safety of persons either directly or indirectly. Do not
use it for such purposes.
Specifications
A Sensor with an open-collector output can be connected to a counter
with a voltage input by connecting a resistor between the power
source and output. Select a resistor with reference to the following
example. The resistance of the resistor is generally 4.7 kΩ and its
wattage is 1/2 W for a supply voltage of 24 V and 1/4 W for 12 V.
EE-SX95 series
Insert a resistor
Counter (Voltage input type)
+Vcc
24 V
Power supply
R
Input terminal (CP)
Output
Z
0V
0V
(Input impedance:
approx. 5.6 kΩ)
Precautions for Safe Use
Power Supply Voltage
Do not exceed the voltage range
indicated in the specifications.
Applying a voltage exceeding the
specifications or using an AC
power supply may result in rupture
or burning.
Brown
Sensor
White
Blue
Load
Black
Load
SW
main
circuit
Tr
Faulty Wiring
Do not reverse the power supply
polarity. Doing so may result in
rupture or burning.
Brown
Sensor
Blue
White
Load
Black
Load
−
+
Example: EE-SX95 Series
Load Resistance of 4.7 kΩ Connected in a Counter
Counter Specifications
Input impedance
Voltage judged as high level (input ON)
Voltage judged as low level (input OFF)
(
(Load short-circuit)
Load
+
−
5.6 KΩ
4.5 to 30 VDC
0 to 2 VDC
Load Short-circuit
Do not short-circuit the load. (Do
not connect to the power supply.)
Doing so may result in rupture or
burning.
Brown
Sensor
Load
Black
ck
White
Blue
Precautions for Correct Use
Do not use the product in atmospheres or environments that exceed
product ratings.
The high and low levels are found using the following formulas. The
input device specifications must satisfy both formulas.
High level:
5.6 k
Z
×
24 V = 13 V
Input voltage V
H
=
Vcc =
4.7 k+5.6 k
R+Z
Low level:
Vcc
24 V
Load current Ic =
=
= 5.1 mA
≤
50 mA
R
R
Input voltage V
L
≤
1.0 V (Residual voltage for 50-mA load current)
Note:
Refer to the ratings of the Sensor for the residual voltage of the
load current.
●Operating
Environment
Load Short-circuit Protection
•
The EE-SX95 provides load short-circuit protection.
If a load short circuit occurs, the output will go OFF. Check the
wiring and cycle the power supply. The load short-circuit protection
circuit will be reset. The load short-circuit protection will also
operate if the current exceeds the rated load current.
If a capacitive load is being used, make sure that the inrush current
will not exceed the rated load current.
• Do not install the Sensor in the following places to prevent
malfunction or trouble:
1. Places exposed to dust or oil mist
2. Places exposed to corrosive gas
3. Places directly or indirectly exposed to water, oil, or chemicals
4. Outdoor or places exposed to intensive light, such as direct
sunlight
• Be sure to use the Sensor under the rated ambient temperature.
• The Sensor may be dissolved by exposure to organic solvents,
acids, alkali, or aromatic hydrocarbons, aliphatic chloride
hydrocarbons causing deterioration in characteristics. Do not
expose the Sensor to such chemicals.
Other Precautions
• Do not disconnect or wire the cables from the Sensor when power
is supplied to the Sensor, or Sensor damage could result.
• Make sure the total length of the power cable connected to the
product is less than 10 m.
●Installation
• It is assumed that EE-SX95 Sensors will be built into a device.
These Sensors use non-modulated light and are not equipped to
deal with interference from an external light source. When they are
used in locations subject to external light interference, such as
near a window or under an incandescent light, install them to
minimize the effects of external light interference.
• Mount the Sensors securely on a flat surface.
• Use M3 or M2.0 screws to secure the Photomicrosensor. (The
stronger M3 screws are recommended. In addition, use flat
washers and spring washers to prevent the screws from
loosening.) Refer to the following table for the correct tightening
torque.
Screw diameter
Tightening torque
M2.0
0.15 N·m max.
M3
0.54 N·m max.
• If the Sensor is to be used on a moving part, secure the cable
connection point so that it is not directly subjected to stress.
●Other
Precautions
• An output pulse may occur when the power supply is turned ON
depending on the power supply and other conditions. The
operation of the Sensor will be stable 100 ms after turning ON the
power supply.
• Dispose of this product as industrial waste.
●
Wiring
Unused Output Lines
Be sure to isolate output lines that are not going to be used.
Connecting to Devices with Voltage Input
5
Domestic Chip Exchange
京公网安备 11010802033920号
EEWORLD
