Agilent HLMP-Pxxx
Subminiature LED Lamps
Data Sheet
Features
•
Subminiature flat top package
•
– ideal for backlighting and light
piping applications
Subminiature dome package
– diffused dome for wide viewing
angle
– nondiffused dome for high
brightness
TTL and LSTTL compatible 5 volt
resistor lamps
Available in six colors
Ideal for space limited
applications
Axial leads
Available with lead configurations
for surface mount and through
hole PC board mounting
HLMP-Pxxx Series, HLMP-Qxxx Series
HLMP-6xxx Series, HLMP-70xx Series
Description
Flat Top Package
The HLMP-Pxxx Series flat top
lamps use an untinted, non-
diffused, truncated lens to
provide a wide radiation pattern
that is necessary for use in
backlighting applications. The
flat top lamps are also ideal for
use as emitters in light pipe
applications.
Dome Packages
The HLMP-6xxx Series dome
lamps for use as indicators use a
tinted, diffused lens to provide a
wide viewing angle with a high
on-off contrast ratio. High
brightness lamps use an
untinted, nondiffused lens to
provide a high luminous
intensity within a narrow
radiation pattern.
Resistor Lamps
The HLMP-6xxx Series 5 volt
subminiature lamps with built in
current limiting resistors are for
use in applications where space
is at a premium.
Lead Configurations
All of these devices are made by
encapsulating LED chips on
axial lead frames to form molded
epoxy subminiature lamp
packages. A variety of package
configuration options is avail-
able. These include special
surface mount lead configura-
tions, gull wing, yoke lead or
Z-bend. Right angle lead bends
at 2.54 mm (0.100 inch) and
5.08 mm (0.200 inch) center
spacing are available for through
hole mounting. For more
information refer to Standard
SMT and Through Hole Lead
Bend Options for Subminiature
LED Lamps data sheet.
•
•
•
•
•
Device Selection Guide
Part Number: HLMP-xxxx
Standard
Red
P005
DH AS
AlGaAs
Red
P105
P102
6000
Q100
Q105
Q150
Q155
6600
6620
6700
6720
6800
6820
High
Efficiency
Red
P205
P202
6300
6305
7000
High
Perf.
Green
P505
P502
6500
6505
7040
Q600
Q605
Emerald
Green
P605
Device
Outline
Drawing
A
A
B
B
B
B
B
B
Orange
P405
P402
Q400
Q405
Yellow
P305
P302
6400
6405
7019
Device Description
[1]
Untinted, Nondiffused,
Flat Top
Untinted, Diffused, Flat Top
Tinted, Diffused
Untinted, Nondiffused,
High Brightness
Tinted, Diffused, Low Current
Nondiffused, Low Current
Tinted, Diffused, Resistor,
5 V, 10 mA
Diffused, Resistor, 5 V, 4 mA
Ordering Information
HLMX-XXXX-X X X X X
Packaging
Option
Color Bin
Selection
Max. Iv Bin
Min. Iv Bin
4 x 4 Prod.
Part
Number
2
Absolute Maximum Ratings at T
A
= 25°C
Standard
Red
50
1000
DH AS
AlGaAs
Red
30
300
High
Eff.
Red
30
90
6
5
2000
5
500
5
500
5
500
High Perf.
Green
30
90
6
5
500
Emerald
Green
30
90
6
5
500
Parameter
DC Forward Current
[1]
Peak Forward Current
[2]
DC Forward Voltage
(Resistor Lamps Only)
Reverse Voltage (I
R
= 100
µA)
Transient Forward Current
[3]
(10
µs
Pulse)
Orange
30
90
Yellow
20
60
6
5
500
Units
mA
mA
V
V
mA
Operating Temperature Range:
Non-Resistor Lamps
-55 to +100
Resistor Lamps
Storage Temperature Range
For Thru Hole Devices
Wave Soldering Temperature
[1.6 mm (0.063 in.) from body]
For Surface Mount Devices:
Reflow Soldering Temperature
-40 to +100
55 to +100
-40 to +85
-55 to +100
260°C for 5 seconds
-40 to +100
-20 to +100
-20 to +85
°C
°C
260°C for 20 seconds
Notes:
1. See Figure 5 for current derating vs. ambient temperature. Derating is not applicable to resistor lamps.
2. Refer to Figure 6 showing Max. Tolerable Peak Current vs. Pulse Duration to establish pulsed operating conditions.
3. The transient peak current is the maximum non-recurring peak current the device can withstand without failure. Do not operate these lamps at this
high current.
4
Power technology
京公网安备 11010802033920号
EEWORLD
