Freescale Semiconductor
Addendum
Document Number: QFN_Addendum
Rev. 0, 07/2014
Addendum for New QFN
Package Migration
This addendum provides the changes to the 98A case outline numbers for products covered in this book.
Case outlines were changed because of the migration from gold wire to copper wire in some packages. See
the table below for the old (gold wire) package versus the new (copper wire) package.
To view the new drawing, go to Freescale.com and search on the new 98A package number for your
device.
For more information about QFN package use, see EB806:
Electrical Connection Recommendations for
the Exposed Pad on QFN and DFN Packages.
© Freescale Semiconductor, Inc., 2014. All rights reserved.
MC9S08AW60 Features
8-Bit HCS08 Central Processor Unit (CPU)
•
•
•
•
•
40-MHz HCS08 CPU (central processor unit)
20-MHz internal bus frequency
HC08 instruction set with added BGND
instruction
Single-wire background debug mode interface
Breakpoint capability to allow single breakpoint
setting during in-circuit debugging (plus two
more breakpoints in on-chip debug module)
On-chip real-time in-circuit emulation (ICE) with
two comparators (plus one in BDM), nine
trigger modes, and on-chip bus capture buffer.
Typically shows approximately 50 instructions
before or after the trigger point.
Support for up to 32 interrupt/reset sources
Up to 60 KB of on-chip in-circuit programmable
FLASH memory with block protection and
security options
Up to 2 KB of on-chip RAM
Clock source options include crystal, resonator,
external clock, or internally generated clock
with precision NVM trimming
Optional computer operating properly (COP)
reset
Low-voltage detection with reset or interrupt
Illegal opcode detection with reset
Illegal address detection with reset (some
devices don’t have illegal addresses)
Wait plus two stops
ADC
— Up to 16-channel, 10-bit
analog-to-digital converter with automatic
compare function
SCI
— Two serial communications interface
modules with optional 13-bit break
SPI
— Serial peripheral interface module
•
IIC
— Inter-integrated circuit bus module to
operate at up to 100 kbps with maximum bus
loading; capable of higher baud rates with
reduced loading
Timers
— One 2-channel and one 6-channel
16-bit timer/pulse-width modulator (TPM)
module: Selectable input capture, output
compare, and edge-aligned PWM capability on
each channel. Each timer module may be
configured for buffered, centered PWM
(CPWM) on all channels
KBI
— Up to 8-pin keyboard interrupt module
Up to 54 general-purpose input/output (I/O)
pins
Software-selectable pullups on ports when
used as inputs
Software-selectable slew rate control on ports
when used as outputs
Software-selectable drive strength on ports
when used as outputs
Master reset pin and power-on reset (POR)
Internal pullup on RESET, IRQ, and BKGD/MS
pins to reduce customer system cost
•
•
•
•
•
•
•
•
•
Input/Output
•
•
Memory Options
•
•
Clock Source Options
System Protection
•
•
•
•
Package Options
MC9S08AW60/48/32
• 64-pin quad flat package (QFP)
• 64-pin low-profile quad flat package (LQFP)
• 48-pin low-profile quad flat package (QFN)
• 44-pin low-profile quad flat package (LQFP)
MC9S08AW16
• 48-pin low-profile quad flat package (QFN)
• 44-pin low-profile quad flat package (LQFP)
Power-Saving Modes
•
•
Peripherals
•
•
51mcu
京公网安备 11010802033920号
EEWORLD
