MN101C49G, MN101C49H, MN101C49K
Type
Internal ROM type
ROM (byte)
RAM (byte)
Package (Lead-free)
128K
4K
MN101C49G
MN101C49H
Mask ROM
160K
6K
MN101C49K
MN101CF49K
FLASH
224K
10K
MN101CP49K
EPROM
Minimum Instruction
Execution Time
LQFP100-P-1414, QFP100-P-1818B
[Standard]
0.10
µs (at
4.5
V to
5.5
V,
20
MHz)
0.238
µs (at
2.7
V to
5.5
V,
8.39
MHz)
125
µs (at
2.0
V to
5.5
V,
32
kHz)*
[Double speed]
0.12
µs (at
4.5
V to
5.5
V,
8.39
MHz)
0.25
µs (at
3.0
V to
5.5
V,
4
MHz)
62.5
µs (at
2.0
V to
5.5
V,
32
kHz)*
* The lower limit for operation guarantee for EPROM built-in type is
2.7
V.
* The lower limit for operation guarantee for flash memory built-in type is
4.5
V.
Interrupts
RESET, Watchdog, External
0
to
5,
Timer
0
to
4,
Timer
6,
Timer
7
(2 systems), Time base, Serial
0
to
3,
Automatic transfer finish,
A/D conversion finish, Key interrupts (8 lines)
Timer counter
0
:
8-bit
×
1
(square-wave/8-bit PWM output, event count, generation of remote control carrier, pulse width measurement)
Clock source................
1/2, 1/4
of system clock frequency;
1/1, 1/4, 1/16, 1/32, 1/64
of OSC oscillation clock frequency;
1/1
of
XI oscillation clock frequency; external clock input
Interrupt source ........... coincidence with compare register
0
Timer counter
1
:
8-bit
×
1
(square-wave output, event count, synchronous output event)
Clock source................
1/2, 1/8
of system clock frequency;
1/1, 1/4, 1/16, 1/64, 1/128
of OSC oscillation clock frequency;
1/1
of
XI oscillation clock frequency; external clock input
Interrupt source ........... coincidence with compare register
1
Timer counter
0, 1
can be cascade-connected.
Timer Counter
Timer counter
2
:
8-bit
×
1
(square-wave/8-bit PWM output, event count, synchronous output event, pulse width measurement)
Clock source................
1/2, 1/4
of system clock frequency;
1/1, 1/4, 1/16, 1/32, 1/64
of OSC oscillation clock frequency;
1/1
of
XI oscillation clock frequency; external clock input
Interrupt source ........... coincidence with compare register
2
Timer counter
3
:
8-bit
×
1
(square-wave output, event count, generation of remote control carrier)
Clock source................
1/2, 1/8
of system clock frequency;
1/1, 1/4, 1/16, 1/64, 1/128
of OSC oscillation clock frequency;
1/1
of
XI oscillation clock frequency; external clock input
Interrupt source ........... coincidence with compare register
3
Timer counter
2, 3
can be cascade-connected.
Timer counter
4
:
8-bit
×
1
(square-wave/8-bit PWM output, event count, pulse width measurement, serial
1
baud rate timer)
Clock source................
1/2, 1/4
of system clock frequency;
1/1, 1/4, 1/16, 1/32, 1/64
of OSC oscillation clock frequency;
1/1
of
XI oscillation clock frequency;
1/1
of external clock input frequency
Interrupt source ........... coincidence with compare register
4
Timer counter
6
:
8-bit
freerun timer
Clock source................
1/1
of system clock frequency;
1/1, 1/4096, 1/8192
of OSC oscillation clock frequency;
1/1, 1/4096,
1/8192
of XI oscillation clock frequency
Interrupt source ........... coincidence with compare register
6
MAD00011HEM
MN101C49G, MN101C49H, MN101C49K
Timer counter
7
:
16-bit
×
1
(square-wave/16-bit PWM output, cycle / duty continuous variable, event count, synchronous output evevt, pulse width
measurement, input capture)
Clock source................
1/1, 1/2, 1/4, 1/16
of system clock frequency;
1/1, 1/2, 1/4, 1/16
of OSC oscillation clock frequency;
1/1,
1/2, 1/4, 1/16
of external clock input frequency
Interrupt source ........... coincidence with compare register
7
(2 lines)
Time base timer (one-minute count setting)
Clock source................
1/1
of OSC oscillation clock frequency;
1/1
of XI oscillation clock frequency
Interrupt source ...........
1/128, 1/256, 1/512, 1/1024, 1/8192, 1/32768
of clock source frequency
Watchdog timer
Interrupt source ...........
1/65536, 1/262144, 1/1048576
of system clock frequency
Serial interface
Serial
0
: synchronous type/UART (full-duplex)
×
1
Clock source................
1/2, 1/4
of system clock frequency; pulse output of timer counter
2, 4; 1/2, 1/4, 1/16, 1/64
of OSC
oscillation clock frequency
Serial
1
: synchronous type/simple UART (half-duplex)
×
1
Clock source................
1/2, 1/4
of system clock frequency; pulse output of timer counter
4; 1/2, 1/4, 1/16, 1/64
of OSC oscillation
clock frequency
Serial
2
: synchronous type
×
1
Clock source................
1/2, 1/4
of system clock frequency; pulse output of timer counter
3; 1/2, 1/4, 1/16, 1/32
of OSC oscillation
clock frequency
Serial
3
: synchronous type/single-master I²C
×
1
Clock source................
1/2, 1/4
of system clock frequency; pulse output of timer counter
3; 1/2, 1/4, 1/16, 1/32
of OSC oscillation
clock frequency
DMA controller
Max. Transfer cycles :
255
Starting factor : external request, various types of interrupt, software
Transfer mode :
1-byte
transfer, word transfer, burst transfer
I/O Pins
I/O
Input
73
(72)
15
(14)
Common use , Specified pull-up resistor available, Input/output selectable (bit unit)
( ) : Flash memory built-in type.
Common use , Specified pull-up resistor available
( ) : Flash memory built-in type.
A/D converter
D/A converter
8-bit
×
4-ch.
10-bit
×
8-ch.
(with S/H)
Special Ports
Buzzer output, remote control carrier signal output, high-current drive port
Correcting address designation : up to
3
addresses possible
ROM Correction
MAD00011HEM
Electrical Charactreistics (Supply current)
Parameter
Symbol
IDD1
Operating supply current
IDD2
IDD3
Supply current at HALT
Supply current at STOP
Supply current at STOP
IDD4
IDD5
IDD6
IDD7
Condition
fosc =
20
MHz , VDD =
5
V
fosc =
8.39
MHz , VDD =
5
V
fx =
32.768
kHz , VDD =
3
V
fx =
32
kHz , VDD =
3
V (5 V), Ta =
25
°
C
fx =
32.768
kHz , VDD =
3
V (5 V) , Ta =
85
°
C
VDD =
5
V , Ta =
25
°
C
VDD =
5
V , Ta =
85
°
C
(
Limit
min
typ
30
15
40
max
70
30
120
30
(90)
3
60
Unit
mA
mA
µA
µA
µA
µA
µA
5
(13)
11
(30)
) : Flash memory built-in type
Development tools
In-circuit Emulator
PX-ICE101C/D+PX-PRB101C49-QFP100-P-1818B
PX-ICE101C/D+PX-PRB101C49-LQFP100-P-1414
Pin Assignment
P74, A12
P73, A11
P72, A10
P71, A9
P70, A8
P67, A7
P66, A6
P65, A5
P64, A4
P63, A3
P62, A2
P61, A1
P60, A0
P54, A17
P53, A16
P52, NCS
P51, NRE
P50, NWE
P47, KEY7
P46, KEY6
P45, KEY5
P44, KEY4
P43, KEY3
P42, KEY2
P41, KEY1
A13, P75
A14, P76
A15, P77
D0, LED0, P80
D1, LED1, P81
D2, LED2, P82
D3, LED3, P83
D4, LED4, P84
D5, LED5, P85
D6, LED6, P86
D7, LED7, P87
SDO0, PD0
SDO1, PD1
SDO2, PD2
SDO3, PD3
SDO4, PD4
SDO5, PD5
SDO6, PD6
SDO7, PD7
DAVSS
DA0, PC0
DA1, PC1
DA2, PC2
DA3, PC3
DAVDD
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
MN101C49G
MN101C49H
MN101C49K
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
P40, KEY0
P37, NDKDMA
P36, NSTDMA
P35, NLDDMA, SCL, SBT3
P34, NBT, SBI3
P33, NBR, SDA, SBO3
P32, SBT1
P31, RXD1, SBI1
P30, TXD1, SBO1
P17(VPP)
P16, TM4IO
P15
P14, TM7IO
P13, TM3IO
P12, TM2IO
P11, TM1IO
P10, TM0IO, RMOUT
P27, NRST
P26(VDD2)
P25, IRQ5
P24, IRQ4
P23, IRQ3
P22, IRQ2
P21, IRQ1, SENS
P20, IRQ0
VREF-
AN0, PA0
AN1, PA1
AN2, PA2
AN3, PA3
AN4, PA4
AN5, PA5
AN6, PA6
AN7, PA7
VREF+
VDD
OSC2
OSC1
VSS
XI
XO
MMOD
SBO0, P00
SBI0, P01
SBT0, P02
SBO2, P03
SBI2, P04
SBT2, P05
NDK, BUZZER, P06
SYSCLK, P07
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
QFP100-P-1818B
LQFP100-P-1414
Note) ( ): Flash memory built-in type.
MAD00011HEM
Request for your special attention and preca
semiconductors de
(1)
If any of the products or technical information described in thi
regulations of the exporting country, especially, those with regar
(2) The technical information described in this book is intended onl
of the products, and no license is granted under any intellectua
company. Therefore, no responsibility is assumed by our comp
company which may arise as a result of the use of technical info
(3) The products described in this book are intended to be used for s
equipment, communications equipment, measuring instruments
Consult our sales staff in advance for information on the followi
–
Special applications (such as for airplanes, aerospace, automo
systems and safety devices) in which exceptional quality and
ucts may directly jeopardize life or harm the human body.
–
Any applications other than the standard applications intended.
(4) The products and product specifications described in this book
provement. At the final stage of your design, purchasing, or u
Standards in advance to make sure that the latest specifications s
(5) When designing your equipment, comply with the range of a
(operating power supply voltage and operating environment etc
maximum rating on the transient state, such as power-on, powe
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values
mode, possible to occur to semiconductor products. Measures o
or preventing glitch are recommended in order to prevent physic
(6) Comply with the instructions for use in order to prevent breakd
thermal stress and mechanical stress) at the time of handling, m
damp-proof packing is required, satisfy the conditions, such as s
(7) This book may be not reprinted or reproduced whether wholl
Electric Industrial Co., Ltd. Industrial Co., Ltd.
京公网安备 11010802033920号
EEWORLD
