OPA2682N datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> OPA2682N

OPA2682N: Part NumberOPA2682N; CategoryAnalog mixed-signal IC Amplifier circuit; File Size9119.93，22 Pages; ManufacturerRochester Electronics; Websitehttps://www.rocelec.com/

Alternative parts

Part Number	Manufacturer	Description
Sorry, there is no alternative parts yet

OPA2682N Overview

OPA2682N amplifier basic information:

OPA2682N is a BUFFER. The commonly used packaging method is SOP-14

OPA2682N amplifier core information:

The minimum operating temperature of the OPA2682N is -40 °C and the maximum operating temperature is 85 °C. Its peak reflow temperature is NOT SPECIFIED

How to simply check the efficiency of an amplifier? Looking at its slew rate, the OPA2682N has a nominal slew rate of 2100 V/us. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the OPA2682N gain becomes 0.707 times the low-frequency gain is 330 MHz.

The nominal supply voltage of the OPA2682N is 5 V, and its corresponding nominal negative supply voltage is -5 V. The input offset voltage of the OPA2682N is 7500 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of OPA2682N:

The width of OPA2682N is: 3.9 mm and the length is 8.65 mm. OPA2682N has 14 terminals. Its terminal position type is: DUAL. Terminal pitch is 1.27 mm. Total pins: 14

OPA2682N amplifier additional information:

Its temperature grade is: INDUSTRIAL. And its humidity sensitivity level is: NOT SPECIFIED. It contains lead. The corresponding JESD-30 code is: R-PDSO-G14. The corresponding JESD-609 code is: e0.

The packaging code of OPA2682N is: SOP. The OPA2682N package materials are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR. The OPA2682N package pin forms are: SMALL OUTLINE. Its terminal forms are: GULL WING.

The maximum seat height is 1.75 mm.

Recommended Resources

ramp generator circuit

Power supply circuit diagram without power transformer

Square wave calibrator circuit diagram using CW136

Typical application circuit buck circuit diagram of LT1111

Walkman fast charger

555 dynamic display LED digital clock equipped with hourly language timekeeping circuit

Calculation and setting of baud rate of msp430 microcontroller: By setting three baud rate-related registers, namely the baud rate integer UxBR1, UxBR0, and the baud rate trim register UxMCTL, the baud rate control parameters are calculated using the following formula: Baud rate parameter (UxBR0, UxBR1) = ...; 火辣西米秀 Microcontroller MCU

Where can I buy this sensor?: I replied to you in another post. It is available on Taobao, and it is most likely OPT101. Thanks~ Give me the material number and quantity and I will ask my friend for you. ...; 靳大龙 Making friends through disassembly

[MYD-JX8MMA7 development board based on ARM+FPGA architecture] Performance test - Network port performance test: Preface Previously, we conducted performance tests on CPU, storage, etc. Now we will conduct performance tests on the network port, the most commonly used communication interface. Prepare Because you need to import and export large files to th...; qinyunti Industrial Control Electronics

Is it better to use logic level MOS or standard level MOS for DCDC circuit driving?: Is it better to use a logic level MOS or a standard level MOS for driving the DCDC circuit? Is there any difference when using it? [Is it better to use logic level MOS or standard level MOS for DCDC circuit driving? 】 Are there any MOS tubes des...; 小太阳yy Switching Power Supply Study Group

A brief history of supercascode: Although wide bandgap semiconductors have made some progress in power switching applications, they have not made any progress in the high voltage/high power field dominated by IGBTs. However, "supercascode" using SiC FETs will change the status q...; 兰博 RF/Wirelessly

LCD display module programming: Programming of MG-12232 module In the initialization part of the system program, the registers and temporary variables used in the program should be described, such as: unsigned char TRANS ; unsigned char PAGEADD ; //...; rain MCU

OPA2682N Also View