MAX478CSA+ datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> MAX478CSA+

MAX478CSA+: Part NumberMAX478CSA+; CategoryAnalog mixed-signal IC Amplifier circuit; File Size2688.71，13 Pages; ManufacturerMaxim; Websitehttps://www.maximintegrated.com/en.html; Environmental Compliance

Alternative parts

Part Number	Manufacturer	Description
MAX478CSA	Rochester Electronics LLC	Basic information about MAX478CSA amplifier:MAX478CSA is an OPERATIONAL AMPLIFIER. The commonly used...
MAX478CSA-T	Maxim Integrated Products	Precision Amplifiers
MAX478CSA+T	Maxim Integrated Products	Basic information of MAX478CSA+T amplifier:MAX478CSA+T is an OPERATIONAL AMPLIFIER. Commonly used pa...

MAX478CSA+ Overview

MAX478CSA+ amplifier basic information:

MAX478CSA+ is an OPERATIONAL AMPLIFIER. Commonly used packaging methods are SOP, SOP8,.25

MAX478CSA+ amplifier core information:

The MAX478CSA+ has a minimum operating temperature of 70 °C and a maximum operating temperature of 70 °C. Its peak reflow temperature is 260. Its maximum bias current at 25°C is: 0.006 µA. Its maximum average bias current is 0.007 µA.

How to simply check the efficiency of an amplifier? Looking at its slew rate, the MAX478CSA+ has a nominal slew rate of 0.025 V/us. The manufacturer specifies a maximum slew rate of 0.056 mA for the MAX478CSA+ and a minimum slew rate of 0.013 V/us. Its minimum voltage gain is 45000. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the MAX478CSA+ gain becomes 0.707 times the low-frequency gain is 60 kHz.

The nominal supply voltage of the MAX478CSA+ is 5 V. The input offset voltage of the MAX478CSA+ is 300 µV (Input offset voltage: the compensation voltage added between the two input terminals to make the op amp output terminal 0V (or close to 0V).)

Related dimensions of MAX478CSA+:

The width of MAX478CSA+ is: 3.9 mm and the length is 4.9 mm. MAX478CSA+ has 8 terminals. Its terminal position type is: DUAL. Terminal pitch is 1.27 mm. Total pins: 8

MAX478CSA+ amplifier additional information:

MAX478CSA+ adopts the VOLTAGE-FEEDBACK architecture. It belongs to the low offset class of amplifiers. The frequency compensation status of MAX478CSA+ is: YES. Its temperature grade is: COMMERCIAL. And its humidity sensitivity level is: 1.

It is a micropower amplifier. The MAX478CSA+ is not Rohs certified. It does not contain lead. The corresponding JESD-30 code is: R-PDSO-G8. The corresponding JESD-609 code is: e3.

The package code of MAX478CSA+ is: SOP. The materials used in the MAX478CSA+ package are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR. The MAX478CSA+ package pins are: SMALL OUTLINE. Its terminal forms are: GULL WING.

The maximum seat height is 1.75 mm.

Recommended Resources

DC motor forward and reverse control drive circuit diagram

Transistor time relay circuit 5b

Commonly used non-sinusoidal oscillator circuits, waveforms and frequency calculation formulas-sawtooth wave oscillator-using intermittent oscillators

Economical relay circuit 2

Meiling-Ariston BCD-181 refrigerator circuit

Optical axis line on automatic grain dispensing machine

Schematic diagram - Are these resistors in HDMI used for impedance matching or to withstand static electricity?: As shown in the picture, this is the HDMI signal on the CPU side . My questions: 1. What are these resistors for? Statement 1: Impedance matching Statement 2: Static electricity resistance 2. Should these resistors be placed clos...; 普拉卡图 PCB Design

Analysis of the whole process of IAR microcontroller programming software from project establishment to program burning: Microcontroller programming software has many applications in actual projects. Each microcontroller programming software and even different versions of microcontroller programming software have their own characteristics. This article will cover tw...; fish001 Microcontroller MCU

How to use stm to make lcd12864 display: There is hardware and software to control it Write the program in the STM microcontroller you play with,,,, For example, initialize the IO port and display screen first, and then a series of process programs can be displayed. 12864 is a c...; 杨学森 stm32/stm8

How to encapsulate GPIO into nodes.: A: How can I encapsulate a GPIO into a node of /sys/device/platform/rst. B: Does it have to be in this directory /sys/device/platform/? Is there a way to only pull it up or down? A: The node required is /sys/devices/platform/unisound/uni_rst, wh...; 明远智睿Lan Industrial Control Electronics

How to control two dsp of hyperlink to initialize and synchronize two dso: As the title says: I would like to ask all the seniors and masters, thank you very much for your guidance. How to handle the initialization synchronization of two dsp in hyperlink? It is necessary to control the initialization of another dsp in one d...; 一丶语 DSP and ARM Processors

EEWORLD University Hall----Live Replay: MPS new generation micro power isolation power module MIE series new product introduction: Live replay: MPS new generation micro power isolated power module MIE series new product introduction : https://training.eeworld.com.cn/course/68179 ...; hi5 Integrated technical exchanges

MAX478CSA+ Also View