ALD1702BPAXXXX datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Analog mixed-signal IC> Amplifier circuit> ALD1702BPAXXXX

ALD1702BPAXXXX: Part NumberALD1702BPAXXXX; CategoryAnalog mixed-signal IC Amplifier circuit; File Size3127.45，6 Pages; ManufacturerALD [Advanced Linear Devices]

Alternative parts

Part Number	Manufacturer	Description
ALD1702BSAXXXX	Advanced Linear Devices Inc	ALD1702BSAXXXX amplifier basic information:ALD1702BSAXXXX is an OPERATIONAL AMPLIFIER.ALD1702BSAXXXX...

ALD1702BPAXXXX Overview

ALD1702BPAXXXX amplifier basic information:

ALD1702BPAXXXX is an OPERATIONAL AMPLIFIER.

ALD1702BPAXXXX amplifier core information:

The minimum operating temperature of the ALD1702BPAXXXX is and the maximum operating temperature is 70 °C. Its maximum average bias current is 0.0003 µA

How to simply check the efficiency of an amplifier? Looking at its slew rate, the nominal slew rate of ALD1702BPAXXXX is 2.1 V/us. When the op amp is used in closed loop, at a certain closed-loop gain (usually 1 or 2, 10, etc.), the frequency when the ALD1702BPAXXXX gain becomes 0.707 times the low-frequency gain is 1500 kHz.

The nominal supply voltage of the ALD1702BPAXXXX is 2.5 V, and its corresponding nominal negative supply voltage is -2.5 V. The upper limit of its supply voltage is 13.2 VALD1702BPAXXXX. The input offset voltage is 2800 µV (input offset voltage: the compensation voltage added between the two input terminals to make the output terminal of the operational amplifier 0V (or close to 0V).)

Related dimensions of ALD1702BPAXXXX:

ALD1702BPAXXXX has 8 terminals. Its terminal position type is: DUAL. Total pins: 8

ALD1702BPAXXXX amplifier additional information:

Its temperature grade is: COMMERCIAL. The corresponding JESD-30 code is: R-PDIP-T8. ALD1702BPAXXXX packaging materials are mostly PLASTIC/EPOXY. The package shape is RECTANGULAR. The ALD1702BPAXXXX package pin format is: IN-LINE.

Its terminal form is: THROUGH-HOLE.

Recommended Resources

Low-voltage circuit breaker for dual power supply (motor closing) mutual switching circuit

Lighting emergency light circuit

Can type FM radio circuit diagram

Diode AND gate decoding circuit (2)

25W, 50W and 100W amplifiers

Negative output voltage integrated regulated power supply composed of BG602 Part 2

[The 3rd Xuantie Cup RISC-V Application Innovation Competition] LicheePi 4A 01 Unboxing + System Burning + Environment Construction: I am very lucky to be shortlisted for this Xuantie Cup competition. Because I was shortlisted in the second batch, I had the experience of the first batch of big guys. I unpacked and lit up the board as soon as I got it. This article will share the...; bzhou830 XuanTie RISC-V Activity Zone

Made a progressive volume control circuit: The effect of installing it on my headphone amplifier: (The machine cannot be covered; the green PCB below is also an additional one, input switching circuit.) The board was made when the 5 yuan proofing started, but I just didn't start soldering. 5...; cruelfox DIY/Open Source Hardware

[N32L43X Review] 4. Analog SPI drive OLED: The previous two articles 2. Analog I2C Driven OLED 3. Hardware I2C Driven OLED introduced the I2C bus to drive the OLED display, and this article introduces the SPI serial bus to drive the OLED display. SPI is a high-speed, full-duplex, synchr...; 805721366 Domestic Chip Exchange

【RPi PICO】Flashing light: After installing the micropython firmware, you need to use the terminal software to connect to the RPi PICO, just like other micropython development boards. From the manual, you can see that the LED uses GPIO25, so you can control the LED by sett...; dcexpert MicroPython Open Source section

Has anyone done OTA online upgrade for RL78?: I have seen the OTA upgrade of stm32 done by the big guys before: The flash is divided into three areas: bootloader area, APP1, APP2. Now I encounter the following problems: 1: The difference between RL78bootloader and STM32; 2: Which library ...; wdm0219 Renesas Electronics MCUs

Detailed explanation of PWM control principle and circuit application: 1 PWM (Pulse Width Modulation) is a technology that uses pulses to output analog signals. It modulates the width of a series of pulses to produce an equivalent target waveform. It is widely used in measurement, communication, switching power suppl...; smls_小森 Power technology

ALD1702BPAXXXX Also View