4176 views|7 replies

112

Posts

0

Resources
The OP
 

The chip does not work when powered on [Copy link]

When the board is plugged in or out while it is powered on, the chip enters an unknown state, which is neither sleep mode nor normal working mode. It cannot work at all. It returns to normal after powering on again or resetting the hardware.

This post is from Analogue and Mixed Signal

Latest reply

If hot plugging is required, are hot plugging measures considered in the power circuit? The most common interface hot-swap is USB hot-swap   Details Published on 2022-2-23 13:17

1w

Posts

25

Resources
2
 

Looks like a power or power-on reset problem

This post is from Analogue and Mixed Signal
 
 
 

2w

Posts

341

Resources
3
 

Refer to the chip manual to check whether all the voltages of the chip power supply meet the requirements.

This post is from Analogue and Mixed Signal

Comments

There may be impact during the plugging and unplugging process, but it cannot be restored after stabilization, and power must be turned on again. Moreover, the defective rate of the problem is not high, and it is not easy to occur on the same board. Is there any better troubleshooting method?  Details Published on 2022-2-23 10:16
 
 
 

9717

Posts

24

Resources
4
 

I also think it may be as mentioned on the second floor, the possibility of abnormal reset is relatively high.

This post is from Analogue and Mixed Signal
 
 
 

112

Posts

0

Resources
5
 
qwqwqw2088 posted on 2022-2-22 22:03 Check the chip manual to see if all the voltages of the chip related to power supply meet the requirements

There may be impact during the plugging and unplugging process, but it cannot be restored after stabilization, and power must be turned on again. Moreover, the defective rate of the problem is not high, and it is not easy to occur on the same board. Is there any better troubleshooting method?

This post is from Analogue and Mixed Signal

Comments

If it is necessary to plug and unplug under power, has the power circuit considered hot-plug measures? The most common interface hot-plug is USB hot-plug  Details Published on 2022-2-23 13:17
 
 
 

4817

Posts

4

Resources
6
 

Start measuring from the initial access point to see if the operating point voltage is correct.

This post is from Analogue and Mixed Signal
 
 
 

2w

Posts

341

Resources
7
 
cxq742536574 posted on 2022-2-23 10:16 There may be impact during the plug-in and unplug process, but it cannot be restored after stabilization. It must be powered on again, and the defective rate of the problem is not high. The same board...

If hot plugging is required, are hot plugging measures considered in the power circuit?

The most common interface hot-swap is USB hot-swap

This post is from Analogue and Mixed Signal

Comments

In actual use, there is no need to plug or unplug the power supply. This is just a problem encountered during the test process. Now there is a problem that even pulling the hardware reset pin directly cannot restore it. This is more serious.  Details Published on 2022-2-23 17:21
 
 
 

112

Posts

0

Resources
8
 
qwqwqw2088 posted on 2022-2-23 13:17 If live plugging is required, does the power circuit take into account hot-plugging measures? The most common interface hot-plugging is USB hot-plugging

In actual use, there is no need to plug or unplug the power supply. This is just a problem encountered during the test process. Now there is a problem that even pulling the hardware reset pin directly cannot restore it. This is more serious.

This post is from Analogue and Mixed Signal
 
 
 

Guess Your Favourite
Find a datasheet?

EEWorld Datasheet Technical Support

Featured Posts
Start → Run → Command Encyclopedia

This post was last edited by jameswangsynnex on 2015-3-3 20:00 winver---------Check the Windows version wmimgmt.msc--- ...

PIC series microcontroller programming basics

This book is a great help to those who want to learn PIC microcontrollers. This book is a basic tutorial book and a good ...

Many places are competing to deploy 5G to accelerate the realization of autonomous driving

This year's government work report proposed to strengthen the construction of new infrastructure, develop a new generati ...

Please help explain how the resistor values shown in the figure are estimated. Thank you

This circuit controls a micro DC motor to rotate forward and reverse to open and close the water meter valve. Please hel ...

Design of wireless network sensor based on Bluetooth protocol

Abstract: Based on the sensor interface standard IEEE1451.2, this paper introduces some specific technical points for th ...

Can you guys give me some advice?

Last year, I switched from hardware to Linux development. At that time, I was working on drivers. When I went out for in ...

[HPM-DIY] openmv for hpm6750 Progress 2 (face recognition 29fps+)

Openmv for hpm has been updated by the author in the past few days, mainly fixing the following: 644525 In addition, us ...

Network port isolation transformer network cable side protection and routing

662606 As shown in the figure above, the upper side is a network port isolation transformer, U43 is a clamping diode, th ...

[Biosensor Evaluation Platform MAX30001GEVKIT] ECG Tester Based on MAX30001G

WeChat https://mp.weixin.qq.com/s?__biz=MzkwMzAyNjYzNQ==&mid=2247485902&idx=1&sn=499bd7ee963044554f9922b36f770b61 ...

What can embedded systems do in the era of artificial intelligence?

In artificial intelligence hardware acceleration, embedded systems play an indispensable role with their unique advantag ...

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号
快速回复 返回顶部 Return list