Training

Location:Training / Embedded Development / Embedded operating system / Linux network environment setup / The development board network cable is directly connected to the USB to network port, and the computer WIFI is used to access the Internet.

You can log in to your eeworld account to continue watching：
The development board network cable is directly connected to the USB to network port, and the computer WIFI is used to access the Internet.
Login

Chapter 1：Basic concepts of network environment construction
Chapter 2：Lecture 1.1 Network environment construction types
Chapter 3：The development board network cable is directly connected to the computer network port, and the computer WIFI is used to access the Internet.
Chapter 4：The development board network cable is directly connected to the USB to network port, and the computer WIFI is used to access the Internet.
Chapter 5：Another method is to directly connect the development board network cable to the USB port
Chapter 6：The network cable of the development board is directly connected to the computer network port, and the computer does not access the Internet.
Chapter 7：The development board network cable is directly connected to the router switch network port, and the computer WIFI accesses the Internet.
Chapter 8：The development board network cable is directly connected to the router switch network port, and the computer network cable is used to access the Internet.
Chapter 9：Network file transfer testing and common problem handling
Chapter 10：TFTP and NFS mount systems
Chapter 11：Not using the network mount system

Duration：29 minutes and 58 seconds
Date：2023/04/22

Uploader：EE大学堂

Introduction

keywords： Punctual Atom Linux Networking

This course teaches you step-by-step how to set up a network environment for virtual machines and Linux development boards. The development board provided by the course is the Punctual Atomic alpha/mini Linux development board/STM32MP157/MP157 MINI development board.

You Might Like

Recommended Posts

Maintenance issues of soldering iron: [i=s]This post was last edited by paulhyde on 2014-9-15 09:35[/i] I would like to ask you: After using the soldering iron for a period of time, the temperature of the soldering iron tip cannot reach t; gina Electronics Design Contest

VxWorks interface and POSIX interface in VxWorks: I just started learning VxWorks, and there is a question that has always confused me when reading the documentation. The documentation says that VxWorks defines both VxWorks interfaces and you can als; se7enmoon Real-time operating system RTOS

The linear regulators or switching regulators we use generally have a maximum current limit. What does this mean specifically?: [backcolor=rgb(222, 240, 251)]The linear regulators or switching regulators we use generally have a maximum current limit. What does this mean specifically? Does it mean that if the current exceeds th; 乐君羊 Analogue and Mixed Signal

Why does the DC signal change so much before and after driving the LD after passing through the bias Tee circuit?: 50mA current drives LD, the output power of LD is 30uW. 50mA current drives LD through the bias Tee circuit, so the output power of LD should also be 30uW. Why does the power of LD increase 20 times a; szyang Analog electronics

Serial communication related: Please give me some advice, thanks. . I have three questions: 1. Now RS232 serial port usually uses 9-frame connection line. The simplest connection is 3 connection lines, namely ground connection (co; luoxianbo Embedded System

What is wrong with the following timer configuration? Why doesn't the timer interrupt occur?: void delay(); void timer0(void); unsigned int count; main(void) { InitSysCtrl(); DINT; IER=0x0000; IFR=0x0000; InitPieCtrl(); InitPieVectTable(); There is no problem with the above program, and other; jonny0811 Microcontroller MCU

Recommended Content

Hot VideosMore

Hot ArticlesMore

Circuit

可能感兴趣器件

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews

Room 1530, 15th Floor, Building B, No.18 Zhongguancun Street, Haidian District, Beijing, Postal Code: 100190 China Telephone: 008610 8235 0740

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京B2-20211791 京ICP备10001474号-1 电信业务审批[2006]字第258号函

京公网安备 11010802033920号