Altium Designer 22 Electronic Design Introduction Practical Lectures 56

Many students have previously reported that our practical design courses are mainly about the whole process of creating a PCB from scratch. They have learned a lot of knowledge related to PCB design. However, for novices, mastering the tools is also very necessary. After all, "rice" No matter how delicious it is, if you don’t know how to use chopsticks, it still doesn’t taste good.” In this course, we will make up for the shortcomings of novices who are not proficient in tools and teach all aspects of electronic design (schematic design and PCB design) using Altium Designer. Commonly used operations are listed, and then in-depth explanations and demonstrations are provided one by one, allowing students to quickly master the basic use of the software and quickly get started with practical PCB design.

Our aim is: to provide technical guidance until you learn it

The first part of the course introduction and AD software installation.

Lesson 01 A complete set of practical video learning methods and precautions.

Lesson 02 AD22 installation and activation and switching between Chinese and English versions.

The second part is the creation operation of the principle library.

Lesson 03 Create a blank Complete electronic design engineering

Lesson 04 Introduction to component symbols and creation of simple resistor and capacitor principle libraries

Lesson 05 Creation of complex principle libraries (diodes, op amps, etc.)

Lesson 06 How to call other people’s schematic libraries

Lesson 07 Checking the correctness of schematic libraries and generate reports

Lesson 08 Size settings and precautions for schematic pages

Lesson 09 Schematic library call and device placement

Lesson 10 Copying, cutting, rotating and mirroring of components

Lesson 11 Arrangement and alignment of components

Lesson 12 Lesson Drawing device wires and wire attribute settings

Lesson 13 Placement of device network label links

Lesson 14 Placement of non-electrical objects (auxiliary lines, text, etc.)

Lesson 15 Sorting of component number numbers and precautions

Lesson 16 How to quickly search Components in the schematic diagram

Lesson 17 Compilation and checking of common errors in schematic diagram

Lesson 18 Export of BOM material list Lesson

19 PDF printout of schematic diagram

Lesson 20 Summary of common design shortcut commands for schematic diagram

The third part of PCB packaging Composition and creation

Lesson 21 PCB package element composition and simple PCB package creation

Lesson 22 Special-shaped pad PCB package creation

Lesson 23 Utilization of IPC package creation wizard

Lesson 24 Library installation and how to call other people’s PCB libraries

Lesson 25 PCB packaging Inspection and report

Lesson 26 3D PCB package model calling and creation

Part 4 PCB import and pre-processing

Lesson 27 How to import schematic diagram into PCB and common import errors

Lesson 28 Quickly define PCB board frame and DXF import definition

Lesson 29 Precise definition of fixing holes and components

Lesson 30 Definition and addition of

stack-up Part 5 Introduction to PCB layout and routing operation commands

Lesson 31 Interactive and modular layout operations of PCB

Lesson 32 Introduction to common operation commands of PCB layout

Chapter 33 Lesson Opening and Closing of Mouse Lines Lesson

34 Class Creation and Class Application

Lesson 35 Introduction to Common Operating Commands of PCB Routing Lesson

36 Introduction to Active Route’s Automatic Routing Lesson

37 Addition and Removal of Teardrops

Lesson 38 Partial Application Adding copper and network Lesson

39 Creation of special-shaped copper cladding Lesson

40 Placement of Cutout and correction and optimization of copper cladding

Part 6 Introduction to common rules for PCB wiring

Lesson 41 Common rules-explanation of spacing rules

Lesson 42 Common rules -Explanation of wiring line width rules

Lesson 43 Rule enabling and priority setting

Lesson 44 Explanation of vias, solder masks and other important rules Lesson

45 Full connection and cross-pad link copper laying rules

Lesson 46 What It is the addition of difference and difference rules.

Lesson 47: Setting of area rules (Room rules).

Lesson 48: Export and import of rules.

Part 7: Post-processing of PCB and output of Gerber files.

Lecture 49: DRC electrical performance inspection of PCB.

Chapter 50 Talk about PCB size marking

Lesson 51 PCB point-to-point and edge distance measurement

Lesson 52 Adjustment of device number silk screen Lesson

53 PCB board LOGO and QR code placement

Lesson 54 Multi-layer circuit and assembly drawing PDF output

Chapter 5 Lecture 55: Output steps for producing Gerber files

Lecture 56: Summary and later planning of PCB design projects

• Chapter 1：A complete set of practical video learning methods and precautions (10 minutes and 52 seconds)

• Chapter 2：AD22 installation and activation and switching between Chinese and English versions (18 minutes and 31 seconds)

• Chapter 3：Create a blank, complete electronic design project (9 minutes and 1 seconds)

• Chapter 4：Introduction to component symbols and creation of simple resistor and capacitor principle library (16 minutes and 44 seconds)

• Chapter 5：Creation of complex schematic libraries (diodes, operational amplifiers, etc.) (18 minutes and 22 seconds)

• Chapter 6：How to call other people’s schematic libraries (7 minutes and 49 seconds)

• Chapter 7：Check schematic libraries for correctness and generate reports (11 minutes and 19 seconds)

• Chapter 8：Schematic page size settings and precautions (6 minutes and 18 seconds)

• Chapter 9：Schematic library call and device placement (8 minutes and 34 seconds)

• Chapter 10：Copy, cut, rotate and mirror components (7 minutes and 18 seconds)

• Chapter 11：Arrangement and alignment of components (3 minutes and 57 seconds)

• Chapter 12：Draw device wires and wire attribute settings (10 minutes and 22 seconds)

• Chapter 13：Place device net label link (8 minutes and 9 seconds)

• Chapter 14：Non-electrical object placement (auxiliary lines, text, etc.) (18 minutes and 6 seconds)

• Chapter 15：Sequence of tag numbers of components and matters needing attention (12 minutes and 7 seconds)

• Chapter 16：How to quickly find components in a schematic (5 minutes and 11 seconds)

• Chapter 17：Compilation and checking of common errors in schematic diagrams (18 minutes and 16 seconds)

• Chapter 18：Export of BOM material table (8 minutes and 26 seconds)

• Chapter 19：PDF printout of schematic (4 minutes and 21 seconds)

• Chapter 20：Summary of commonly used design shortcut commands for schematic diagrams (12 minutes and 0 seconds)

• Chapter 21：PCB package element composition and simple PCB package creation (19 minutes and 36 seconds)

• Chapter 22：Special-shaped pad PCB package creation (21 minutes and 40 seconds)

• Chapter 23：Utilization of IPC package creation wizard (16 minutes and 15 seconds)

• Chapter 24：Library installation and how to call other people’s PCB libraries (12 minutes and 27 seconds)

• Chapter 25：PCB packaging inspection and report (12 minutes and 6 seconds)

• Chapter 26：3DPCB package model calling and creation (21 minutes and 29 seconds)

• Chapter 27：How to import schematic diagram into PCB and common import errors (15 minutes and 22 seconds)

• Chapter 28：Quickly define PCB board frame and DXF import definition (17 minutes and 20 seconds)

• Chapter 29：Precise definition of fixing holes and components (11 minutes and 54 seconds)

• Chapter 30：Definition and addition of cascades (10 minutes and 47 seconds)

• Chapter 31：Interactive and modular layout operations for PCB (12 minutes and 11 seconds)

• Chapter 32：Introduction to common operating commands for PCB layout (26 minutes and 18 seconds)

• Chapter 33：Opening and closing of rat wire (16 minutes and 20 seconds)

• Chapter 34：Class creation and Class application (15 minutes and 8 seconds)

• Chapter 35：Introduction to common operating commands for PCB wiring (33 minutes and 35 seconds)

• Chapter 36：Introduction to automatic routing of Active Route (10 minutes and 53 seconds)

• Chapter 37：Adding and removing teardrops (10 minutes and 31 seconds)

• Chapter 38：Partial copper pouring and addition of network in Lesson A (14 minutes and 3 seconds)

• Chapter 39：Use of AD script files in Lesson B (13 minutes and 22 seconds)

• Chapter 40：Creation of special-shaped copper deposits (8 minutes and 31 seconds)

• Chapter 41：Cutout placement and copper coating correction and optimization (9 minutes and 27 seconds)

• Chapter 42：Commonly used rules-explanation of spacing rules (15 minutes and 3 seconds)

• Chapter 43：Common rules-explanation of wiring width rules (7 minutes and 30 seconds)

• Chapter 44：Enabling rules and setting priorities (7 minutes and 40 seconds)

• Chapter 45：Explanation of vias, solder mask and other important rules (14 minutes and 36 seconds)

• Chapter 46：Copper Laying Rules for Fully Connected and Cross Pattern Links (10 minutes and 12 seconds)

• Chapter 47：What is difference and the addition of difference rules (16 minutes and 30 seconds)

• Chapter 48：Settings of regional rules (Room rules) (7 minutes and 1 seconds)

• Chapter 49：Export and import of rules (6 minutes and 40 seconds)

• Chapter 50：DRC electrical performance inspection of PCB (29 minutes and 21 seconds)

• Chapter 51：PCB size marking (6 minutes and 57 seconds)

• Chapter 52：PCB point-to-point and edge distance measurement (5 minutes and 59 seconds)

• Chapter 53：Adjustment of device number silk screen printing (14 minutes and 42 seconds)

• Chapter 54：PCB board LOGO and QR code placement (15 minutes and 8 seconds)

• Chapter 55：Multi-layer wiring and assembly drawing PDF output (12 minutes and 34 seconds)

• Chapter 56：Output steps for producing Gerber files (23 minutes and 7 seconds)

• Chapter 57：Summary and later planning of PCB design project (8 minutes and 52 seconds)