PADS VX2.7 beginners’ zero-based introduction to PCB Layout design 52 practical courses

PADS VX2.7 will be used. In order to facilitate beginners to directly see the design of the 4-layer board, the PADS software has three components. The basic usage of the three components of Logic, Layout, and Router corresponds to the schematic diagram, layout, and wiring respectively. According to the PCB The process decision will start from the beginning, from the overall project introduction, schematic library and package library creation, schematic drawing, network table synchronization, board and frame design, PCB layout, PCB wiring to PCB post-processing, etc., each link will be demonstrated through actual cases. , and finally designed a complete PCB and generated the GERBER of the board, so that everyone can truly understand why we do this? What else can be done?

Lesson 1 Course Introduction Lesson
02 PADS VX2.7 version software installation and cracking
Lesson 03 Introduction to the PADS Logic software operation interface and common settings
Lesson 04 Creating a PADS Logic software logic library
Lesson 05 Creating a PADS Logic software component library
Lesson 06 Introduction to the corresponding relationship between component library, logic library and package library
Lesson 07 Create, add and rename schematic page
Lesson 08 Add components to PADS Logic software schematic Lesson
09 PADS Logic software schematic signal connection
Lesson 10 PADS Logic software Add power supply and ground to the schematic diagram
Lesson 11 Add BUS to the schematic diagram
of PADS Logic software Lesson 12 Save the component library in the schematic diagram to the specified library Lesson
13 BOM file and schematic pdf document output
Lesson 14 PADS Logic and Layout Synchronous PCB import and import error analysis
Lesson 15 Introduction to the PADS Layout software operation interface and common settings
Lesson 16 Structure import and board and frame drawing
Lesson 17 Importing boards and frames using AD software
Lesson 18 ORCAD software version schematic diagram import into PCB
Lesson 19 Principle block diagram, power supply binary tree analysis
Lesson 20 Introduction to commonly used shortcut keys and modeless commands of PADS Layout software
Lesson 21 PADS Layout software and PADS Logic synchronize modular capture of devices
Lesson 22 Introduction to filter tool
Lesson 23 Device movement, Introduction to rotation and flip operations
Lesson 24 Introduction to device, network, and via locking and unlocking operations
Lesson 25 Stacking settings Lesson
26 Via addition
Lesson 27 color settings
Lesson 28 Layout, wiring rule settings and detailed explanation
Lesson 29 Signals Class setting and rule setting
Lesson 30 Special rule setting
Lesson 31 Introduction to PCB
layout Lesson 32 Introduction to wiring and line repair functions of PADS Layout software Lesson
33 Copper foil processing of PADS Layout software
Lesson 34 Introduction to fan hole operation of PADS Layout software
Lesson 35 Lesson
36 Introduction to PCB package creation Lesson 36 Introduction to PADS Router software operation interface and common settings
Lesson 37 Introduction to general design rule settings of PADS Router software
Lesson 38 Introduction to PADS Router wiring and repair functions
Lesson 39 Introduction to PADS Router copper drawing and adjustment
Lesson 40: Introduction to fan hole operation of PADS Router software
Lesson 41: Introduction to BGA automatic fan-out operation of PADS Router software
Lesson 42: Introduction to differential rule setting and differential wiring and line repair functions of PADS Router software
Lesson 43: Introduction to PCB wiring
Lesson 44: PADS Router Software snake shape equal length rule setting and addition
Lesson 45 PADS Layout software connectivity and safe distance DRC inspection and elimination
Lesson 46 Wiring, copper optimization, Mark point addition
Lesson 47 Silk screen adjustment and assembly drawing PDF file output
Lesson 48 Gerber file settings
Lesson 49 Introduction to Gerber file output
Lesson 50 IPC netlist and device coordinate generation
Lesson 51 Checking Gerber files using Cam350 software Lesson
52 File archiving and project summary

• Chapter 1：Course Introduction (16 minutes and 43 seconds)

• Chapter 2：PADS VX2.7 version software installation and cracking (30 minutes and 13 seconds)

• Chapter 3：Introduction to Logic software operation interface and common settings (17 minutes and 58 seconds)

• Chapter 4：Create PADS Logic software logic library (12 minutes and 33 seconds)

• Chapter 5：Create Logic software component library (9 minutes and 34 seconds)

• Chapter 6：Introduction to the correspondence between component libraries, logic libraries, and packaging libraries (7 minutes and 49 seconds)

• Chapter 7：Create, add and rename schematic pages (8 minutes and 57 seconds)

• Chapter 8：PADS Logic software schematic diagram adding components (12 minutes and 37 seconds)

• Chapter 9：PADS Logic software schematic diagram signal connection (14 minutes and 58 seconds)

• Chapter 10：Add power and ground to Logic software schematic diagram (6 minutes and 12 seconds)

• Chapter 11：Add BUS to PADS Logic software schematic diagram (7 minutes and 33 seconds)

• Chapter 12：Save the component library in the schematic to the specified library (4 minutes and 17 seconds)

• Chapter 13：BOM file and schematic pdf document output (8 minutes and 56 seconds)

• Chapter 14：Logic netlist import and error analysis (24 minutes and 20 seconds)

• Chapter 15：Introduction to Layout software operation interface and common settings (22 minutes and 42 seconds)

• Chapter 16：Structure import and plate and frame drawing (29 minutes and 18 seconds)

• Chapter 17：Use AD software to import boards and frames (16 minutes and 4 seconds)

• Chapter 18：ORCAD software version schematic diagram imported to PCB (20 minutes and 28 seconds)

• Chapter 19：Schematic block diagram, power supply binary tree analysis (22 minutes and 31 seconds)

• Chapter 20：Introduction to commonly used shortcut keys and modeless commands in Layout software (19 minutes and 51 seconds)

• Chapter 21：Schematic synchronization for modular grabbing devices (9 minutes and 57 seconds)

• Chapter 22：Filter tool introduction (10 minutes and 29 seconds)

• Chapter 23：Introduction to device movement, rotation, and flip operations (16 minutes and 25 seconds)

• Chapter 24：Introduction to device, network, via locking and unlocking operations (6 minutes and 45 seconds)

• Chapter 25：Overlay settings (19 minutes and 29 seconds)

• Chapter 26：Via addition (15 minutes and 18 seconds)

• Chapter 27：Color settings (13 minutes and 31 seconds)

• Chapter 28：Layout and wiring rule settings and detailed explanations (13 minutes and 59 seconds)

• Chapter 29：Signal class settings and rule settings (9 minutes and 6 seconds)

• Chapter 30：Special rule settings (8 minutes and 20 seconds)

• Chapter 31：PCB layout introduction (38 minutes and 15 seconds)

• Chapter 32：Introduction to the wiring and repair functions of Layout software (10 minutes and 26 seconds)

• Chapter 33：PADS Layout software copper foil processing (26 minutes and 14 seconds)

• Chapter 34：Introduction to fan hole operation in PADS Layout software (17 minutes and 19 seconds)

• Chapter 35：Introduction to PCB package creation (18 minutes and 41 seconds)

• Chapter 36：Introduction to Router software operation interface and common settings (11 minutes and 4 seconds)

• Chapter 37：Introduction to general design rule settings of Router software (6 minutes and 49 seconds)

• Chapter 38：Introduction to Router wiring and repair functions (5 minutes and 32 seconds)

• Chapter 39：Introduction to Router Copper Drawing and Adjustment (10 minutes and 21 seconds)

• Chapter 40：Router software fan hole operation introduction (9 minutes and 38 seconds)

• Chapter 41：Introduction to Router software BGA automatic fan-out operation (18 minutes and 23 seconds)

• Chapter 42：Introduction to differential signal wiring and wiring repair functions (18 minutes and 30 seconds)

• Chapter 43：Introduction to PCB wiring (1 hours and 18 minutes and 25 seconds)

• Chapter 44：Router software snake-shaped equal length rule setting and addition (19 minutes and 48 seconds)

• Chapter 45：Connectivity and safe distance DRC inspection and elimination (16 minutes and 40 seconds)

• Chapter 46：Routing, copper optimization, and mark point addition (26 minutes and 13 seconds)

• Chapter 47：Silk screen adjustment and assembly drawing PDF file output (19 minutes and 31 seconds)

• Chapter 48：Gerber file settings (21 minutes and 26 seconds)

• Chapter 49：Introduction to Gerber file output (6 minutes and 31 seconds)

• Chapter 50：IPC netlist and device coordinate generation (5 minutes and 44 seconds)

• Chapter 51：Check Gerber files using Cam350 software (6 minutes and 40 seconds)

• Chapter 52：Lesson file archiving, project summary (10 minutes and 12 seconds)