Training
Profile
Market trends in health and medical care ● Principles and solutions of biosensors ● Introducing Maxim’s health and medical reference design HSP2.0 to fully understand Maxim’s overall solutions in the health and medical field. Maxim’s reference design HSP2.0 helps shorten products Development cycle to achieve high-precision, low-power PPG, ECG and other functions ● HSP2.0 demonstration time
Chapters
Chapter 1：An in-depth explanation of wearable health monitoring part 1 (40 minutes and 30 seconds)
Chapter 2：An in-depth explanation of wearable health monitoring part 2 (10 minutes and 30 seconds)
Chapter 3：HSP2.0 demo (10 minutes and 30 seconds)
You Might Like
Recommended Posts
- The introductory book on DSP recommended by senior students: "Teaching you to learn DSP step by step"
- I am going to learn DSP in the next stage. My senior recommended me a good introductory book "Teaching You to Learn DSP Step by Step" and sent me an electronic version. Good things should be shared wi
-
电力小子
DSP and ARM Processors
- Introduction to calling DSP functions of TMS320F28335
- The first function is: CFFT_f32_sincostable(cfft) Among them, cfft is one of the above structures. The function of this function is to calculate the conversion factor of Fourier transform. From the fo
-
fish001
DSP and ARM Processors
- Request YUV422 PLANAR ----> rgb565, or request YUV422 PLANAR --> yuv420 conversion code
- Request YUV422 PLANAR ----> rgb565, or request YUV422 PLANAR --> yuv420 conversion code
-
linguoxian
Embedded System
- The production of digital display high sensitivity FM stereo front end
- [img]http://www.v4s.cn/wp-content/uploads/autosave/2007/10/20071023061203u.jpg[/img] This digital FM stereo front end has a sensitivity index of 0.5μV 20dB S/N, which is still considered very high tod
-
黑衣人
RF/Wirelessly
- Chip Function
- The pinout of the P2110 chip is shown in the figure. The datasheet says that the RF Input Power cannot exceed 23dBm, otherwise the chip will be damaged. So how do general chips ensure that it does not
-
badmanfirst
RF/Wirelessly
- PIC microcontroller cannot start after USB power-on
- Just asking, I don't know if there is a problem with the USB port or insufficient power supply. The PIC18 microcontroller cannot start after plugging in the USB data cable. If you twist the USB interf
-
goo128
Microchip MCU
Recommended Content
Web users are watching Change
- The introductory book on DSP recommended by senior students: "Teaching you to learn DSP step by step"
- Introduction to calling DSP functions of TMS320F28335
- Request YUV422 PLANAR ----> rgb565, or request YUV422 PLANAR --> yuv420 conversion code
- The production of digital display high sensitivity FM stereo front end
- Chip Function
- PIC microcontroller cannot start after USB power-on
- Power Electronics Courseware Animation
- Servo systems enable fast and accurate production changes
- How to Layout a Circuit Board for an Op Amp
- Texas Instruments: TMS320C5535 eZdsp USB Development Kit Demonstration
- Power Sequencing for Electronic Products
- [Repost] Help me up, I can still model!
- Multithreading on LM3S8962_phtotthreads
- Running Debian system on K510 (unsuccessful compilation)
- Digitally controlled voltage source design, need help!
- Understanding Inductance
- 【MSP430 Sharing】Design of Embedded Networked Instrument Monitoring System
- UWB transceiver DW1000 chip internal diagram
- What RF people must know: A journey of discovery of electromagnetic waves
- It seems that i have got a job
- Can anyone provide the corresponding Vbe curve of the transistor Vce/Ic amplification, saturation, and cutoff curves?
- This section is getting very hot. Which topic are you going to participate in? What is the main controller you have chosen?
- What is the command to delete a folder in vxWorks shell?
- Help with a programmer issue
- Am I suitable for learning embedded microcontrollers?
- [XMC4700 Relax 5V shield review] 01 Unboxing experience
- Solution to the problem that the file name is too long to be deleted when using LPCXpresso
- If the input signal travels 100 meters, is it better to connect it to the positive pole or the negative pole of the optocoupler?
- How to add the entire directory under WINCE 5.0?
- Let’s talk about MIPS?
Popular Components
Just Take a Look
Hot Downloads
- Newnes.-.Programming.16-Bit.PIC.Microcontrollers.in.C
- Analysis of the mobile phone market from 2006 to 2007
- Traffic lights based on C language proteus simulation
- Decomposition and reconstruction example 1
- 74ABT374
- CCNA Video Tutorial 36
- Learn digital electronic technology from me.rar
- RTL8305SB_Power_Consumption_v1
- FDW9926A
- The name \"Flash\"
MoreHot Articles
- Analysis of white LED backlight dimming solution
- Mouser Now Stocking Qorvo QPQ1298 High-Performance BAW Filter
- Groundbreaking Bayesian Deep Learning Enables Energy-Efficient AI
- Ask the court to declare that its 5G patent licensing rates comply with the FRAND principle
- STM32 collects signals from DHT11 temperature and humidity sensor
- How to operate an infrared spectrophotometer?
- STM8L151C8 MCU learning routine (13) - DHT11
- Details determine success or failure--Three key points in the design of the power supply system of the electronic blood pressure monitor
- Huawei's fourth major event: seven years of planning and three years of invisibility, what are the chances of success or failure?
- Qualcomm presents industry-leading AI innovations and collaborations at CES 2025, covering PCs, cars, smart homes and enterprise
京公网安备 11010802033920号