The asymmetry of the parallel-axis electric drive axle geometry significantly increases the angle between the torque shaft and the motor shaft (B1). The torque shaft suspension arrangement is no longer suitable for electric drive axles.
Assembly;
The motor's low speed, high torque and fast response characteristics require that the suspension has strong limit and torsion resistance while the housing has sufficient support strength;
The center of mass arrangement can well balance the reaction force of the suspension support, so that the support shell can evenly resist the impact load and improve the fatigue resistance of the structure.
Previous article：Application case of body domain controller based on Chipsea Technology CS32F036Q
Next article：Discussing the calibration and control principles of permanent magnet synchronous motors for new energy vehicles
CVPR 2023 Paper Summary: Computer Vision Theory
AD642SH/883B
Recommended Content
Latest Embedded Articles
- Huawei's Strategic Department Director Gai Gang: The cumulative installed base of open source Euler operating system exceeds 10 million setsOn November 15, the first AI native open source operating system openEuler, openEuler 24 03 LTS version, was officially released on June 6 this year. ...
- Analysis of the application of several common contact parts in high-voltage connectors of new energy vehiclesIntroduction: Connectors are used in every car. The device uses electrical, optical and other signals to control the corresponding mechanical force to connect, disconnect and convert, thereby realizing the corresponding circuit or optical channel conversion. ...
- Wiring harness durability test and contact voltage drop test methodBased on the QC T 29106-2014 standard, this paper proposes a new durability characteristic test and contact voltage drop test method, and conducts experimental verification on these two test methods. ...
- Sn-doped CuO nanostructure-based ethanol gas sensor for real-time drunk driving detection in vehiclesMetal oxides and their composites with other materials (such as MXenes and metal chalcogenides) can be used to achieve different ...
- Design considerations for automotive battery wiring harnessThe battery is one of the power sources of the car. When the generator stops working and the engine is started, all the power is output from the battery. When the engine is idling or working at a low speed, the power generation of the generator cannot meet the demand. ...
- Do you know all the various motors commonly used in automotive electronics?
- What are the functions of the Internet of Vehicles? What are the uses and benefits of the Internet of Vehicles?
- Power Inverter - A critical safety system for electric vehicles
- Analysis of the information security mechanism of AUTOSAR, the automotive embedded software framework
He Limin Column
Microcontroller and Embedded Systems Bible
Professor at Beihang University, dedicated to promoting microcontrollers and embedded systems for over 20 years.
MoreSelected Circuit Diagrams
MorePopular Articles
- Innolux's intelligent steer-by-wire solution makes cars smarter and safer
- 8051 MCU - Parity Check
- How to efficiently balance the sensitivity of tactile sensing interfaces
- What should I do if the servo motor shakes? What causes the servo motor to shake quickly?
- 【Brushless Motor】Analysis of three-phase BLDC motor and sharing of two popular development boards
- Midea Industrial Technology's subsidiaries Clou Electronics and Hekang New Energy jointly appeared at the Munich Battery Energy Storage Exhibition and Solar Energy Exhibition
- Guoxin Sichen | Application of ferroelectric memory PB85RS2MC in power battery management, with a capacity of 2M
- Analysis of common faults of frequency converter
- In a head-on competition with Qualcomm, what kind of cockpit products has Intel come up with?
- Dalian Rongke's all-vanadium liquid flow battery energy storage equipment industrialization project has entered the sprint stage before production
MoreDaily News
- Allegro MicroSystems Introduces Advanced Magnetic and Inductive Position Sensing Solutions at Electronica 2024
- Car key in the left hand, liveness detection radar in the right hand, UWB is imperative for cars!
- After a decade of rapid development, domestic CIS has entered the market
- Aegis Dagger Battery + Thor EM-i Super Hybrid, Geely New Energy has thrown out two "king bombs"
- A brief discussion on functional safety - fault, error, and failure
- In the smart car 2.0 cycle, these core industry chains are facing major opportunities!
- The United States and Japan are developing new batteries. CATL faces challenges? How should China's new energy battery industry respond?
- Murata launches high-precision 6-axis inertial sensor for automobiles
- Ford patents pre-charge alarm to help save costs and respond to emergencies
- New real-time microcontroller system from Texas Instruments enables smarter processing in automotive and industrial applications
Guess you like
- How to make a sensorless brushless DC motor driver board
- Today at 10:00 AM, live broadcast with awards: Internet of Everything - Shijian Company and Microchip experts jointly discuss IoT solutions
- What are the advantages and disadvantages of MOS tubes and relays as electronic switches? In what situations would relays or MOS tubes be preferred?
- Looking for domestic wireless charging chip manufacturers
- Detailed explanation of 5G OTA testing technology
- Analog IC Design Resource Download
- DSP chip selection tips
- MPlab IDE cannot be opened after reinstallation
- The product cannot be connected to the Internet, and the displayed time cannot be updated through the network. The LCD displays the date and time inaccurately. From which angles can it be solved...
- EEWORLD University Hall ---- Top 10 Raspberry Pi Designs in 2019
京公网安备 11010802033920号