Schematic diagram of 1W stereo headphone amplifier based on TDA2822

Publisher:calmrsLatest update time:2022-07-06 Source: elecfansKeywords:TDA2822  amplifier Reading articles on mobile phones Scan QR code
Read articles on your mobile phone anytime, anywhere

The following circuit diagram is the schematic diagram of a 1W stereo headphone amplifier. This circuit is built on TDA2822 and is designed for portable players, radios, and other common electronic devices that can use headphones for audio output.


A 3V power supply/battery can be used to drive the headphones, providing 20mW per channel into 32 ohms. This circuit can use a small 8? speaker as an audio output, but you will need a 9V power supply, and the circuit will provide 1W of power output.


IC KA2209 is equivalent to IC TDA2822, can KA2209 be used? If TDA2822 cannot be found.

poYBAGK_o6OATKPSAAFAjluhQRY075.png


Keywords:TDA2822  amplifier Reference address:Schematic diagram of 1W stereo headphone amplifier based on TDA2822

Previous article:Circuit diagram analysis based on M66T melody generator
Next article:How to make a smart watch using ESP32 and ILI9488

Recommended ReadingLatest update time:2024-11-16 12:49

Design of a Small Preamplifier for Electret Microphone
With the rapid development of China's communications industry, the demand for electret microphones is increasing. At present, although some small electret microphones can integrate field effect tubes into the microphone, the high price of high-end products and the inability to guarantee the accuracy and sensitivity of
[Power Management]
Design of a Small Preamplifier for Electret Microphone
Low-cost 1W high-power LED practical driver application
  High-power LEDs have higher luminous efficiency and service life than fluorescent lamps. People should install a heat sink according to the actual usage. At present, the retail price of domestic 3W white light LED is 15 yuan, but because the quality of 3W high-power LED is not reliable enough, it is not suitable for
[Power Management]
Low-cost 1W high-power LED practical driver application
Extraordinary tube amplifier design
The PCB board of this bile duct secondary amplifier is made of 2mm thickened board, coated with black printing ink, and has enhanced heat dissipation design. After the production is completed, the machine is tested and the effect is extraordinary.   1. Circuit Principle   The circuit is shown in Figures A and B be
[Analog Electronics]
Extraordinary tube amplifier design
Wide dynamic range logarithmic amplifier
Wide dynamic range logarithmic amplifier
[Analog Electronics]
Wide dynamic range logarithmic amplifier
8W audio amplifier with frequency up to 200KHZ
8W audio amplifier with frequency up to 200KHZ Function of the circuit The high-frequency characteristics of monolithic power ICs used in audio equipment are usually not very good. For devices such as sensors with a frequency of tens of kilohertz, there are very few ICs available. In view of this situation, dis
[Analog Electronics]
8W audio amplifier with frequency up to 200KHZ
Design Method for Stabilizing Transistor Operating Point in Low Noise Amplifier (Part 1)
In most cases, the useful signal is very weak. In these applications, the noise factor becomes the main parameter to characterize the performance of transistors. This paper discusses a design method of adding parallel resistance to stabilize the transistor operating point in low-noise amplifier circuits. Almost all co
[Power Management]
Design Method for Stabilizing Transistor Operating Point in Low Noise Amplifier (Part 1)
[Image] Gallstone hybrid power amplifier using switching power supply
The preamplifier uses a European TESLA brand low-noise high-cheek dual triode PCC88. The tube has a moderate gain (μ=33), a large anode allowable current (Ia=15mA), a high transconductance (12.5mA/V), and a low anode voltage. It can be connected in SRPP mode to obtain a voltage gain of about 25 times.   In order to im
[Analog Electronics]
[Image] Gallstone hybrid power amplifier using switching power supply
What does low power operational amplifier mean?
What does low power operational amplifier mean? Definition of low-power operational amplifier Since the biggest advantage of electronic circuit integration is that it can make complex circuits small and light, as the application range of portable instruments expands, operational amplifiers with low power supply vol
[Analog Electronics]
What does low power operational amplifier mean?
Latest Embedded Articles
Change More Related Popular Components
Guess you like

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

About Us Customer Service Contact Information Datasheet Sitemap LatestNews


Room 1530, 15th Floor, Building B, No.18 Zhongguancun Street, Haidian District, Beijing, Postal Code: 100190 China Telephone: 008610 8235 0740

Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号