The pressure of the calibrator is unstable or cannot be pressurized normally
1. The oil tank is insufficient. 2. The pipe joints are damaged and leaking during transportation. 3. The "○" ring seal of the quick connector is damaged. 4. There is too much air in the system or it is not exhausted. Treatment method: 1. Loosen the oil tank cap or add oil to the oil tank. 2. Tighten the pipe joints. 3. Replace the "○" ring. 4. Repeatedly pump the oil filling pump to discharge the air in the system with the oil tank. Treatment method: The instrument should be judged according to the actual local atmospheric pressure. The air pressure cannot be pressed, and the pressure pump feels empty. Intelligent pressure calibrator fault 2. Negative pressure does not meet the standard Reason: 1. The reversing valve is not in place, resulting in air leakage. 2. The positive pressure check valve or the negative pressure check valve is not reset after movement, causing air pressure. Treatment method: 1. The reversing valve must be in place, and the reversing valve stem cannot be suspended in the air. 2. Check whether the positive and negative pressure check valve seat holes do not meet the requirements. 3. The spring is severely tilted and the one-way valve core cannot slide freely. (end) |
Previous article:What are the special tests for electromagnetic flowmeters?
Next article:Working principle and advantages of intelligent vortex flowmeter
- Popular Resources
- Popular amplifiers
Recommended Content
Latest Test Measurement Articles
- Keysight Technologies Helps Samsung Electronics Successfully Validate FiRa® 2.0 Safe Distance Measurement Test Case
- From probes to power supplies, Tektronix is leading the way in comprehensive innovation in power electronics testing
- Seizing the Opportunities in the Chinese Application Market: NI's Challenges and Answers
- Tektronix Launches Breakthrough Power Measurement Tools to Accelerate Innovation as Global Electrification Accelerates
- Not all oscilloscopes are created equal: Why ADCs and low noise floor matter
- Enable TekHSI high-speed interface function to accelerate the remote transmission of waveform data
- How to measure the quality of soft start thyristor
- How to use a multimeter to judge whether a soft starter is good or bad
- What are the advantages and disadvantages of non-contact temperature sensors?
MoreSelected Circuit Diagrams
MorePopular Articles
- Innolux's intelligent steer-by-wire solution makes cars smarter and safer
- 8051 MCU - Parity Check
- How to efficiently balance the sensitivity of tactile sensing interfaces
- What should I do if the servo motor shakes? What causes the servo motor to shake quickly?
- 【Brushless Motor】Analysis of three-phase BLDC motor and sharing of two popular development boards
- Midea Industrial Technology's subsidiaries Clou Electronics and Hekang New Energy jointly appeared at the Munich Battery Energy Storage Exhibition and Solar Energy Exhibition
- Guoxin Sichen | Application of ferroelectric memory PB85RS2MC in power battery management, with a capacity of 2M
- Analysis of common faults of frequency converter
- In a head-on competition with Qualcomm, what kind of cockpit products has Intel come up with?
- Dalian Rongke's all-vanadium liquid flow battery energy storage equipment industrialization project has entered the sprint stage before production
MoreDaily News
- Allegro MicroSystems Introduces Advanced Magnetic and Inductive Position Sensing Solutions at Electronica 2024
- Car key in the left hand, liveness detection radar in the right hand, UWB is imperative for cars!
- After a decade of rapid development, domestic CIS has entered the market
- Aegis Dagger Battery + Thor EM-i Super Hybrid, Geely New Energy has thrown out two "king bombs"
- A brief discussion on functional safety - fault, error, and failure
- In the smart car 2.0 cycle, these core industry chains are facing major opportunities!
- The United States and Japan are developing new batteries. CATL faces challenges? How should China's new energy battery industry respond?
- Murata launches high-precision 6-axis inertial sensor for automobiles
- Ford patents pre-charge alarm to help save costs and respond to emergencies
- New real-time microcontroller system from Texas Instruments enables smarter processing in automotive and industrial applications
Guess you like
- There is a circuit for fast shut-off of MOS tube. Does anyone know the specific working principle? How to shut down quickly?
- Application of Field Effect Transistor
- What is overshoot? How to solve the problem of overshoot in high-speed circuit signals
- Where can I find the development environment for the domestically produced aerospace-grade CPU of the BM3803MGRH model?
- What is the difference between using * and ? in the day of the week in cron expressions? I checked some information but it's not clear.
- GD32E231 DIY Contest Brushless Motor Driver
- FAQ Power Management, Battery Management
- Together wow: Smart soldering iron based on domestic chip, portable soldering iron system IronOS (FreeRTOS)
- How to add code to ardunio ide
- Blackboard with 24 touch keys, 9 customizable LEDs