Using transistor as switch

Recommended ContentMore

Open source project More

• 16bit parallel screen
• Multi-channel LDO distribution board v0.3 multi-channel buck power module
• Open source closed-loop stepper motor controller (schematic + source code)
• dht11-module
• Supercapacitor voltage equalizing plate (BW6101) has been tested
• ATMEGA fuse bit restorer
• [Training Camp] Internet of Things Infrared Wireless Remote Control-483530A
• LiNetRex
• NTAG I ² C + Explorer Kit with NFC Reader
• 【Smart Car】Thomas small car 1094966A

Searched by Users

• PCB package library download
• GD32F130 Chinese Manual
• FPGA Engineering Application in Software Radio: Synchronization Technology.pdf
• Omron PLC programming software CX-Programmer7.1 Simplified Chinese version
• C51 MCU Development Tool Keil UV4 (Keil C51 μVision4) v9.01
• Ansoft Maxwell 13 motor electromagnetic field example analysis
• Agilent Gas Chromatography Basic Operations Manual
• Wang Yun 51 single chip microcomputer tutorial book \"51 single chip microcomputer C language programming tutorial\" pdf electronic complete version full set of materials
• Design Guide for Selection of Bootstrap Components
• Small software for transmission line calculation

Just Take a LookMore

• [Raspberry Pi 4B Review] Raspberry Pi 4 drives 3G network card to send and receive text messages and wireless Internet access
  I have a Huawei E353 3G network card, which I can use with the Raspberry Pi 4.Huawei E353 parameters: Network mode: dual mode Bus interface: USB Antenna type: built-in antenna Network type: 3G: HSPA+,
• ESP32 VL53L5CX Multi Zone Range Sensor
• Simple questions about DC motors
  When the output power of the DC motor is close to ideal, the higher the voltage, the faster the speed when the load (rated load) is constant, until the motor is magnetically saturated and the motor bu
• MSP430F5438A MCU Low Power Settings
  MSP430F5438A MCU low power settings, take entering LPM3 as an example: 1. The external clocks of MSP430F5438A are 8M and 32.768 respectively. When the program runs normally, the 8M main clock is selec
• Dual-receive and dual-transmit radio RF board based on XC7Z100+ADRV9009
  1. Board OverviewThe dual-receive and dual-transmit radio RF board based on XC7Z100+ADRV9009 is a special function board developed based on Xilinx ZYNQ FPGA and ADI's wireless transceiver chip ADRV900
• 【Repost】The definition and difference between passive and active signals of sensors
• TI C64x+ DSP CACHE consistency analysis and maintenance
• Some basic knowledge about SPI-Flash
• Is your phone ready for 5G?
• [MSP430] Practical ADC use, internal temperature measurement use

Trending Downloads

• SMD Soldering Tutorial
• An example of implementing one-to-many with Hibernate
• Innovative solutions for a wireless world
• Implement effective solder joint quality analysis to reduce costs and risks in the PCB assembly process
• Top Ten Technology Trends of DAMO Academy in 2020
• Proteus simulation based on 8051 - playing a piece of music
• sm1628 Chinese information
• LM3S328_Microcontroller_DATA_SHEET
• Design of dual-channel power amplifier circuit
• DS1302 Driver

Trending ArticlesMore

• Practical skills | Six power supply design experiences
• iPhone 13 price plummets by 2,000 yuan, and Huawei’s new phone starts at 1,000 yuan. It’s crazy!
• Who is Xie Yuan? Guangxi top scorer in science, top student in the Department of Electronics at Tsinghua University, leader of Alibaba AI chips, and new ACM Fellow
• Qualcomm acquires NXP for $47 billion at 12% premium
• Reviewing the development of RISC-V from previous HotChips
• Deep learning based 3-D object detection based on camera and lidar fusion
• [DLP Series Review 1] First contact with TI DLP3010EVM!
• Useful Information | How to design a PCB to withstand 100 A of current?
• In what aspects can MSP430 replace ARM?