\"Microcontroller Principles and Applications\" electronic teaching plan_1

Recommended ContentMore

Open source project More

• OLED knob keypad
• DC and stepper motor driver IC - TB6612FNG
• DER-259 - Ultra-thin 36.3 W power supply
• Compound OPAMP
• NFC-CUBE: NFC Cube Kit
• ch55X burning adapter
• [DIY Optoelectronic Design] Winter Olympics Snowflake Lanterns
• NCV7429V1GEVB: NCV7429 system base chip evaluation board
• Balance car control panel
• [Training Camp_Advanced Class] Three-way smart socket + temperature display

Searched by Users

• GL823K Datasheet
• The program in the short paper uses RBF neural network to optimize PID controller, and the effect is very good!
• DWIN Serial Port Screen DGUSII Development Guide
• Quasi-Synchronous Sampling Using the Flexible Programmable Sequencer and Burst Mode of the AD7616
• Anlogic EG4S20 FPGA DataSheet V1.4
• PIC ICD2 self-made data (including firmware)
• Multisim10.0 simulation software crack version download
• PC Bluetooth virtual serial port software Bluesoleil3.2 cracked version
• TFTP_Server_TFTPDWIN_v0.4.2 arm kernel download software
• USB Serial Port CP210x Driver

Just Take a LookMore

• Ideas on the development of CM-i.MX7D embedded core board
  After searching for a long time, I found that there is very little information about the CM-i.MX7D embedded core board. So I decided to write one myself. Please forgive me if it is not well written. T
• [RVB2601 Creative Application Development] Start to go through the development process
  [RVB2601 Creative Application Development] Start to go through the development processAfter getting the development board, I started to follow the development process regularly. This time I printed he
• Op amp output clamping mechanism and avoidance methods
  Author: Howard ZouAn operational amplifier is a type of amplifier that can perform different arithmetic operations by changing peripheral devices. Any operational amplifier integrates a lot of transis
• 【Development and application based on NUCLEO-F746ZG motor】11. Parameter configuration - ADC configuration
  In the development of servo drive, ADC acquisition is the key point. The analog quantities in this development board are: three-phase current, 1 bus voltage, and 1 temperature (onboard sensor). After
• [Solved] Why can’t I change my profile picture?
  [i=s]This post was last edited by wsmysyn on 2019-4-2 10:24[/i] The first post of this year is actually about a bug{:1_133:} I just changed my avatar, and it took five minutes to succeed. Then, after
• The STM32F103VBT6 resets with a button. After releasing the button, it takes three or four seconds for the microcontroller to execute the program.
• [Xianji HPM6750 Review] + Unboxing
• C2000 combines capacitive touch and host controller functions
• 7660 chip common mode inductor manufacturer
• "【TGF4042 Signal Generator】" High-frequency distortion measurement

Trending Downloads

• New DSP28335 project in CCS5.5
• MOS semiconductor device principle download
• ML2215 pdf datasheet (Speech Synthesizer plus Music LSI with On-Chip 3 Mbit Mask ROM）
• The latest color illustrations of car computer repair
• A blur effect FLASH. Please give me some advice. Sorry
• Use lpc coefficients to get the spectral envelope
• Imatest Simple Tutorial
• SM7513 low power switching power supply chip 12V0.3A transformer specification
• Journal article: Research on flame image segmentation of coal-fired power plant boiler nozzles
• The LED dot matrix microcontroller program includes PROTEUS simulation

Trending ArticlesMore

• Practical skills | Six power supply design experiences
• iPhone 13 price plummets by 2,000 yuan, and Huawei’s new phone starts at 1,000 yuan. It’s crazy!
• Who is Xie Yuan? Guangxi top scorer in science, top student in the Department of Electronics at Tsinghua University, leader of Alibaba AI chips, and new ACM Fellow
• Qualcomm acquires NXP for $47 billion at 12% premium
• Reviewing the development of RISC-V from previous HotChips
• Deep learning based 3-D object detection based on camera and lidar fusion
• [DLP Series Review 1] First contact with TI DLP3010EVM!
• Useful Information | How to design a PCB to withstand 100 A of current?
• In what aspects can MSP430 replace ARM?