Research on intelligent coding and decoding methods for interface protocols

Recommended ContentMore

Open source project More

• electronic clock
• 51 Simple Stopwatch Counter Design
• Writing machine main control consistent series
• Lithium battery powered DC coupled headphone amplifier
• Eight-channel high-end driver based on VNI8200XP-32
• DER-572 - 10 W non-isolated tapped step-down power supply
• Active clamp forward DC-DC power supply basic simulation circuit
• High-efficiency synchronous rectification boost converter demonstration board based on L6920D
• Infrared pyrolysis control module based on EG4002C
• Raspberry3 shell

Searched by Users

• NI visa driver downloader
• LLC Design-Zhang Weiping
• Agilent E4402B Spectrum Analyzer User Manual
• \"Zigbee Introduction and Practice\" Chapter 1 Introduction to ZigBee.pdf
• Siemens inverter manual download
• 60 examples of Siemens S7-200 PLC programs with explanations
• AVR_fighter 64 bit win10 win8 available programs and drivers USBasp
• Introduction to C language development and project practice (C language learning roadmap)
• Daemon Tools Lite V4.45.4.0315 Official Chinese Version
• The receiving and sending program based on DMX512 protocol on AT89S51 microcontroller

Just Take a LookMore

• The result register value of DSP28377D fluctuates greatly after ADC sampling
  As shown in the figure, no matter I input a constant voltage at the ID port or directly input it at the A0 port, the value of the register ADCRESULT0 is always fluctuating, with a fluctuation value of
• Has anyone used this kind of constant current solution with a single IC for two channels?
  I need to make a two-way output buck constant current solution. Now a chip maker has provided two solutions, one is for 2/1 switching, and one CS pin is used for control. The other is for two-way powe
• It’s the Little New Year! It’s not the Little New Year yet? When does your family celebrate the Little New Year?
  I heard that some places are celebrating the Little New Year today! But some places haven't celebrated the Little New Year yet? When does your family celebrate the Little New Year? Come and vote~ and
• How to use GPIO to simulate I2C to operate EEPROM
  The EEPROM datasheet has the following description: If you use GPIO to simulate I2C to operate the EEPROM, 1) How to distinguish whether it is Standard (100kHz) or Fast (400kHz)? 2) How to use the fol
• In high-speed PCB design, these issues must be paid attention to
  When designing PCB, we often encounter various problems, such as impedance matching, EMI rules, etc. This article has compiled some difficult questions and answers related to high-speed PCB, hoping to
• Participate in the Tektronix Probe Revealing Action and Share the 2019 New Year Red Packet
• Looking for the official SDK of HiSilicon's HI3518EV300
• Temperature Measurement Record--Comparative Measurement
• TMS570x/RM4x LaunchPad: Basic setup of MIBSPI loopback mode based on examples
• [ATmega4809 Curiosity Nano Review] Serial port application preliminary: printing sine string through serial port

Trending Downloads

• The 12th Five-Year Plan for Solar Power Generation Development
• ARM application example (lighting program)
• Electro-optical Q-switched RF-excited waveguide CO2 laser
• S71327
• Learn Android from scratch
• Tsinghua University Electrical Engineering Courseware Model Electronics Part 10
• Microchip MiWiP2P Wireless Protocol
• Circuit Analysis
• Panas2832 Power Supply.pdf
• easyARM8962 ucos message mailbox operation experiment source code

Trending ArticlesMore

• Amplifier input impedance parameters and application simulation
• Run, wireless charging!
• Did Intel really lose?
• [Chongqing Station] Registration for Melexis Sensing Technology Tour Seminar is now open!
• common problem
• Apple's most ambitious chip plan yet
• Summary of the Semiconductor Equipment Market in 2020
• ​ADI & Shijian will help you understand chemical analysis and analytical instrument application solutions. Answer questions and win prizes!