Satellite coordinate calculation

Recommended ContentMore

Open source project More

• [Shandong Agricultural University "Lichuang Cup" Intelligent Control Competition] STM Microcontroller 2
• HyFlightctrl
• HVBMS Centralized Cell Monitoring Unit (CMU) capable of CAN FD communication via MC33775A
• 51 minimal system
• [Frequency Synthesizer] AD9854 Digital Frequency Synthesizer
• 2018 Electronic Competition Question C-Wireless Charging Electric Car (Xidian University)
• KPower supply design for Kintex Ultrascale FPGA: ultra-quiet, 1.8V, 1A
• NCP5603GEVB: High Efficiency Charge Pump Converter/White LED Driver Evaluation Board
• MAXREFDES1107: Small-footprint, 12V/1A, synchronous, optocouplerless flyback DC-DC converter with 92.8% efficiency using the MAX17690 and MAX17606
• matrix clock

Searched by Users

• Qualcomm QC2.0 fast charging protocol identification IC-FP6600
• The display program of the electronic blood pressure monitor is written in MATLAB
• Talking about Dynamic Loading ActiveX Controls in VB6.0
• Summary of the secondary constant current method using TL431 in LED lighting power supply
• [Analog Electronics Basics Study Guide and Teaching Reference]. Wang Yong, Chen Guangmeng. High Definition Text Version.pdf
• Siemens S7-300-400PLC programming software use
• Linux/UNIX System Programming Manual (Part 2)
• smith-chart smith chart impedance matching software--dedicated to users
• TDC-GP22 User Manual
• Allwinner H3 Data Sheet

Just Take a LookMore

• Share a domestic chip 32-bit M4 microcontroller - AT32F403A series
  With the pressure of the 2020 epidemic and the severe international situation, the replacement of domestic chips has become an inevitable trend. It doesn’t matter whether you replace it early or late.
• Patch reverse check
  Can anyone help me figure out what this 5-pin patch is? There are two dots under W1 horizontally, and a P vertically.
• TI C6000 project creation steps
  1. Create a projectAfter successfully installing the CCS development environment, run CodeComposer Studio 5.5.0.exe (default in the start menu). Enter the TI DSP integrated development environment. As
• Please teach me a peak detection circuit composed of an op amp
  The circuit schematic is shown below: The input is a 400kHz half-sine wave signal, Vmax=5.8V, Vmin=-0.4V 1. Is LM393 used as a comparator here? I don't know how to analyze the diode. 2. The op amp at
• EEWORLD University ---- Control system of 100 quantum bits
  100-qubit control system : https://training.eeworld.com.cn/course/4867
• What is the function of this solder joint on the PCB?
• GD32L233C-START Review——03_2.CoreMark Test, RT-Thread-Nano Porting
• A detailed guide to the Industrial Internet of Things: From risks to benefits
• Bidding now: STC 12C5A32S2 September 26 12:00 - September 27 11:59
• How to implement remote monitoring of wind turbines in wind farms?

Trending Downloads

• Main technical knowledge and precautions of LED power supply and drive circuit
• Design of automatic tester for temperature and humidity in warehouse based on 8031 ​​single chip microcomputer
• AVR MCU Bootloader
• The simplest AT8951 program to implement sine wave
• LM57,datasheet,pdf(Resistor-Programmable Temperature Switch)
• Research on Microwave Protection in RF Testing
• X-ray detection system based on LabVIEW and its application in laser Compton scattering experiment
• DM74ALS1005
• Discussion on reactive power compensation at the end of rural low voltage power grid
• AT91SAM926X series linux-2.6.27 patch

Trending ArticlesMore

• Amplifier input impedance parameters and application simulation
• Run, wireless charging!
• Did Intel really lose?
• [Chongqing Station] Registration for Melexis Sensing Technology Tour Seminar is now open!
• common problem
• Apple's most ambitious chip plan yet
• Summary of the Semiconductor Equipment Market in 2020
• ​ADI & Shijian will help you understand chemical analysis and analytical instrument application solutions. Answer questions and win prizes!