Self-made 3D connector library: Female-Header-2.54-SMD-18

Recommended ContentMore

Open source project More

• #The8thLiChuangElectronicContest#ElectronicClock
• JTAG adapter board
• High-speed digital input current limiter evaluation board based on SCLT3-8BQ7
• STM32F411-BOARD
• 2-phase unipolar stepper motor driver IC——TB67S142FTG
• Hot-swappable simple shaft tester with NFC card function
• High efficiency synchronous buck regulator based on L6984
• ExpressCard to USB3.0 board
• Thromboelastography
• FRDM-KL25Z: Freedom development platform for Kinetis ^® KL14, KL15, KL24 and KL25 MCUs

Searched by Users

• MCGS Configuration Software Training Course_Kunlun Tongtai
• MAX485ESA Chinese data MAX485ESA data sheet pdf download
• RK3399 Hardware Design Guide
• Omron FQ Vision Sensor Operation Manual (Chinese)
• EPLAN P8 Parts Library and Macros
• Teaching materials of \"Basics of Analog Electronics Technology\" 4th edition (Edited by Tong Shibai and Hua Chengying)
• J-LINK-V9 Circuit Diagram
• Computer simulation analysis of optocoupler isolation circuit based on PSPICE
• Design Instructions for Wavelet Denoising by Combining Labview and MATLAB
• orcad component library download

Just Take a LookMore

• Please tell me the function of these options in ALTIUM
  Could you please tell me the functions of these 5 options? Thank you. If I want to make grooves or holes on the board, should I draw them on the keepout layer or the mech1 layer?
• [Xingkong Board Python Programming Learning Main Control Board] System Burning
  [i=s]This post was last edited by jinyi7016 on 2022-11-1 09:13[/i]The Xingkong board is essentially a Linux development board with some built-in applications that can support Mind+ software and add a
• GD32L233C-START uses J-Link SWD to download and reports an error!!! Please solve
  Hey guys, for the GD32L233C-START evaluation board, has anyone used J-Link to burn and debug programs (SWD)? I'd like to ask if you have encountered the error "Cannot Load Flash Programming Algorighm!
• 4 charts showing how and when the chip shortage will end
  Source: https://spectrum.ieee.org/chip-shortageFabs using older process nodes are keyHistorians may spend decades analyzing the consequences of the COVID-19 pandemic. But the chip shortage it caused w
• AD19 only shows wireframe after copper is laid, which does not look like laid copper
  Dear friends, why does my AD19 only show the wireframe after copper laying, but not the laid copper, as shown in the picture? Is there any setting? Switch to AD10 and open it, double-click the copper
• 【EVK-NINA-B400 Evaluation Kit】Hardware
• MicroPython 7th Anniversary Celebration
• [Gizwits Gokit3 Review] Unboxing and Getting Started
• This week's evaluation information is presented to you~
• [Evaluation of EC-01F-Kit, the NB-IoT development board of Essence] - Unboxing and power-on test

Trending Downloads

• icc_vG-2012.06-SP2_commonlearning
• Do electromagnetic waves from mobile phones really affect the human body?
• Cadence High Speed ​​PCB Design
• Power frequency slip source using ARM and DDS technology
• Student management code implemented in C language
• Failure Mode Analysis of Fiber Optic Splitter Reliability Test
• uva trilearn robocup source code
• ADC0809 digital oscilloscope, can change parameters arbitrarily, display voltage
• DM74LS293
• MAX9107_

Trending ArticlesMore

• Amplifier input impedance parameters and application simulation
• Run, wireless charging!
• Did Intel really lose?
• [Chongqing Station] Registration for Melexis Sensing Technology Tour Seminar is now open!
• common problem
• Apple's most ambitious chip plan yet
• Summary of the Semiconductor Equipment Market in 2020
• ​ADI & Shijian will help you understand chemical analysis and analytical instrument application solutions. Answer questions and win prizes!