USB field, industry standard for mass storage. Talents who are good at driver work should read this

Recommended ContentMore

Open source project More

• stitp-stm32
• Simple PD2.0/3.0 fast charging decoy
• IoT ECG monitoring based on ESP32
• MAXREFDES1189: 7.5W, 24V offline flyback converter using MAX17595
• USB to TTL with ESP32 automatic download circuit
• tcrt5000
• CH340N programmer
• 【CW32】Brushless DC motor driver board
• Esp_Burnner: Simple 8266 module programmer using USB-C interface
• R_75_V10 design based on IPS2 motor commutation sensor

Searched by Users

• Altium Designer schematic library HT microcontroller.SchLib
• Fortran commonly used algorithm program set - Xu Shiliang\'s very good algorithm summary
• 12V10A switching power supply TL494 circuit diagram
• Tool for serial port debugging ---- Serial Port Wizard, green software that does not need to be installed
• FreeRTOS Development Manual (electronic version of the book, layout is different)
• MK_ISO／ICE - 13818 MPEG-2 protocol standard detailed explanation 440 pages 17.4M.pdf
• 【ISO_UI】Wildfire development board whole board test program
• Sprint-Layout6.0 Green Chinese Version
• Mechanical Design Manual Free Download V3.0 Patch
• Proteus MCU simulation circuit diagram part 2.DSN.c.hex file

Just Take a LookMore

• I'm new to PCB, please give me some guidance, thank you
  The PCB routing is complete, and the DRC check is also OK. Can we go to make the board now? Are there any problems with the vias?
• Does lighttpd support PHP?
  I am using the A5 board. Does lighttpd support PHP? I see that the system has the lighttpd web server enabled by default, and I can access the initial web page. Question: Does this lighttpd support PH
• How to keep the IO port in BlueNRG-1 sleep mode
  I am testing the sleep mode function of BLUENRG-1. I read the official documentation and found that in sleep mode, except for a few IO ports with internal IO9, IO0, and IO11, the other IO ports are in
• 2011 eNewsletter
  2011 eNewsletter
• TI Designs – Precision file question about Bode plots
  I would like to ask where the formula 9 in this file comes from. . Thank you very much, my brain is going to explode after thinking about it. .
• What is the difference between edge triggering (rising edge, falling edge) and level triggering (high level and low level) in digital circuits?
• Does the boost topology circuit limit the duty cycle?
• Op amp differential amplification problem
• FAQ_How to fill in the BQB certification application form
• [2022 Digi-Key Innovation Design Competition] Material Unboxing Raspberry Pi 400

Trending Downloads

• MCU serial port input and output functions
• MSE908KX8,pdf datasheet
• Infrared trash can
• Parse XML documents and display them in a digital structure. A relatively simple program for beginners to learn and use.
• Jitter separation based on Tail Fit algorithm
• PB develops salary management software
• MM74HC4066
• Research on GPS Leveling Polynomial Surface Fitting Model
• Fast video segmentation algorithm
• Power supply MTK6305

Trending ArticlesMore

• Rohde & Schwarz: Practicing 5G testing and jointly promoting 5G commercialization in the future
• NI’s intelligent vehicle testing solutions are now available to accelerate the development of autonomous driving
• Cypress 3.0 helps you turn today's problems into tomorrow's innovations!
• Mid-Autumn Festival‧ Reunion
• Littelfuse Launches Industry’s Smallest Unidirectional TVS Diode Array to Protect I/O and Power Ports from ESD Damage
• The car of the future without rearview mirrors
• Domestic mobile phones are trapped in Qualcomm
• Exclusive interview with Tencent’s Zhong Li: Zhiwen team’s exploration of intelligent question-answering systems