HT82V738 pdf datasheet (24-Bit Stereo Audio D/A Converter)

Recommended ContentMore

Open source project More

• 24V down to 5V adjustable module
• AXP173 Power Module
• Charging board based on ip5318
• CN0216
• Minimal system design based on stm32f103c8t6
• DER-406 - 5.76W high PF non-isolated buck-boost, TRIAC dimmable LED driver for A19 lamps
• box-keychain-esp32
• PT100 temperature measurement circuit (schematic + pcb board diagram)
• Multimeter calibrator
• Single board V1.0

Searched by Users

• OrCAD Capture16.2 Lite Edition.exe
• Mitsubishi PLC from entry to mastery, detailed explanation of the road to learning PLC (with various illustrations) free download
• Driver for Logitech Vision Headsets under Linux
• BPSK, 8PSK, 16QAM, 32QAM, 64QAM demodulation program MATLAB
• Introduction to the Coreline Technology Hummingbird E203 FPGA Development Board and JTAG Debugger
• AB PLC routine, a program written by RSLOGIX500
• USB Serial Converter driverUSB serial port driver
• Wei Dongshan_Embedded LINUX Application Development Complete Manual Video.pdf
• Anlogic EG4S20 FPGA DataSheet V1.4
• YD/T 968-1998 Limits and test values ​​of electromagnetic compatibility of telecommunication terminal equipment

Just Take a LookMore

• Identification of color ring resistors
• Four-quadrant stepper motor control simulation with interpolation calculation and single-chip microcomputer source program
  [color=#252525][size=14px]51 MCU uses ULN2003A chip to drive stepper motor program plus Proteus simulation [/size][/color] [color=#252525][size=14px]The MCU source program is as follows: [/size][/colo
• It's time to change! Awesome change, the latest design to replace RS-485 optocoupler isolation
  [i=s] This post was last edited by Jacktang on 2019-4-12 09:05 [/i] [size=4] Friends who have worked on RS-485 optocoupler isolation circuits must have been annoyed for a long time. This commonly used
• 7V boost to 12V circuit
  There are two ways of thinking: 1. Connect two 7V/1A battery panels in parallel to become a 7V/2A power supply, and then get 12V by 7V to 12V boost; 2. Connect two 7V/1A battery panels in series to ge
• EEWORLD University ---- 3D TOF occupancy detection: body tracking and counting
  3D TOF Occupancy Detection: Body Tracking and Counting : https://training.eeworld.com.cn/course/4988
• [Silicon Labs Development Kit Review] + Temperature and Humidity Sensor Si7021
• Smart socket
• FPGA Design Tips
• PIC microcontroller i2c slave mode receiving data problem
• Purgatory Legend-PLL War

Trending Downloads

• Starting of three-phase asynchronous motor
• RF Circuit
• Agilent 2007 WiMAX Technology Seminar--Download Handouts
• [Document]-JIS C3663-8-2010 Rubber insulated cables for fixed voltages below 450-750V Part 8 High voltage transformer cables.pdf
• Generate the fifteenth derivative of a Gaussian pulse
• GSM Short Message Protocol 0705
• MODBUS communication protocol written on c51 microcontroller platform (assembly)
• Temperature monitoring and alarm system based on DS18B20 and ISD1420
• WAAS MATLAB simulation program
• Learn the basic characteristics of common short-range wireless chips in 5 minutes and make the right choice

Trending ArticlesMore

• Linux Code Review - Linux Kernel Monthly Report (December 2020)
• Huawei Chip 20 Years
• PIC® & AVR® Curiosity Nano Development Board 8th wave of free applications open
• A former NASA engineer made the piano speak English and play the world's most difficult music by itself, so fast that it smokes
• Google's Dropout patent takes effect, and people in the AI ​​community are getting anxious!
• Big companies are making cars, and there are not enough engineers
• The truth behind the high growth of the three major US cloud giants
• Where to connect the ground plane of a switching regulator?
• Next-generation router and switch solutions | Paladin® backplane cable compatibility expands more possibilities!