Pretty good stuff

Recommended ContentMore

Open source project More

• Contactless, precision AC current sensing using Hall Effect sensors
• CH455H_Nigital tube display module
• 38V, 2A synchronous buck switching regulator evaluation board based on L6982CDR
• Resonant LCC 90W notebook power adapter based on L6599 and STP9NK50ZF
• Flying West Lake Vinegar Fish Smoke Generator
• Infrared reversing radar copy
• CH559L minimum system board
• SSTC Solid State Tesla Coil Circuit
• Xu Fan1810300129 The second circuit
• PiEEG: A brain-computer interface based on Raspberry Pi that can measure EEG, EMG and ECG biological signals

Searched by Users

• Ultrasonic cleaning machine based on STM32F105 microcontroller
• 201 principles of software development
• Altera\'s CPLD/FPGA development software Quartus2 Chinese tutorial
• Low voltage distribution cabinet design specification download pdf GB50054-95
• Batterymon v2.1.1 Chinese version authoritative battery testing software
• GJB438B-2009 General requirements for military software development documentation
• 128-bit 2D barcode generator, tested and fully applicable to practical
• LTE protocol stack and signaling analysis
• PIC source code for FM1702sl
• STM32F4 Chinese Manual

Just Take a LookMore

• Several key performance characteristics of the MSP432P401R MCU 14-bit ADC
  [align=left][color=rgb(85, 85, 85)][size=4]We will focus on several key performance features of the [color=#aa6666]MSP432P401R MCU[/color] 14-bit ADC called ADC14; this ADC14 provides the flexibility
• Pin-regulated 8mA output amplifier
  I recently used the Howland constant current source circuit. The amplifier is LMV614. The output currents are 0.5ma, 1ma, 3ma, and 5ma. However, when I finished drawing the board and tested it, I foun
• Problems with adding vias to PCB boards
  As the title says, for example, for a two-layer PCB After copper is applied to both the top GND and the bottom GND Why do we need to place several vias on the GND copper between the two layers? (After
• 2G communication project - power consumption test comparison and analysis of IoT small size modules M26 and M6315 - waiting for suggestions online!
  [align=left]Hello Everyone, your old friend Modultong (Brother Panda) is back. The Spring Festival holiday is gone in a flash, and I believe you all ate, drank and had fun. (This is pure nonsense! No
• (Reward: 5000 RMB) ADS1220 cannot collect data
  [i=s]This post was last edited by chenbingjy on 2019-6-13 08:45[/i]The chip used is STM32F767, and the environment used is MDK5.ADS1220 collects data in 65535.Circuit diagram:program:Could you please
• EEWORLD University ---- Intelligent Control
• EEWORLD University Hall----Design and optimization of buck-boost charging chip compatible with USB-PD protocol
• Self-wound coil inductance calculation assistant
• Showing goods + Qualcomm original QCA4020 development board
• How to enable TI 15.4-Stack to support 470M frequency band

Trending Downloads

• 3D package library project (5)
• This is a book introducing MATLAB modeling and simulation
• W5100 Network Expansion Board Information
• Design of a tens-digit counter based on VHDL language
• The best material for learning HFSS10 hfss_full_book
• RAKE receiver for direct-sequence spread spectrum systemsSimulink model of a simple direct-sequenc
• Design of timer counter chip supporting pwm output
• stm32 self-study notes
• Principles and Applications of Photoelectric Testing Instruments (China Metrology Press + 1989)
• Interface technology between digital controlled potentiometer and PIC microcontroller

Trending ArticlesMore

• Bell Labs' century of ups and downs
• Silicon wafer prices soar, Japanese manufacturers' net profits increase fourfold
• AMD Advantage gaming laptops debut at ChinaJoy, designed specifically for gamers
• Demand surges, hoarding becomes popular, manufacturing industry suffers from "stock shortage + price increase"
• Deeply mourn Mr. Fan Xiaohua
• Tektronix video micro-lecture hall is now open
• AMD Ryzen 7 5700G processor high performance "worry-free choice"