MAX4400-MAX4403 Data Sheet

Recommended ContentMore

Open source project More

• environment-sensor-bluetooth
• USB to CH340N
• audio amplifier
• Huanghuai Maker Development Board
• m.2(ngff) to PCIe x4
• [Internet of Things] Hongmeng Smart WIFI Switch +4233031A
• Open Source-STC15W408AS Minimal System Board
• VNQ7140AJ Evaluation Board
• Yamashina Map
• NCP380HSNAJAGEVB: High-Side Distribution Switch Evaluation Board

Searched by Users

• Efficient Implementation of MAC in FPGA
• MIT Department of Electrical Engineering and Computer Science MATLAB® User Guide
• Tutorial on Finite Element Analysis of Engineering Electromagnetic Fields Using Ansoft Maxwell
• Introduction to Artificial Intelligence: Models and Algorithms (Wu Fei)
• ALTEAR FPGA MAX10 series Altium AD, orcad component library schematic package library
• linphone-2.1, the latest version of SIP phone source code for LINUX platform
• USB 3.1 Connector Association Specification 64 pages 9.1M
• The receiving and sending program based on DMX512 protocol on AT89S51 microcontroller
• FPM_0.080 package generator
• PCI Express System Architecture Standard Textbook

Just Take a LookMore

• FPGA Design Process
  FPGA Design Process
• Power supply obstacles + power supply SBC selection and pitfalls
  Hello everyone, I am an automotive electronics hardware engineer. When selecting a power SBC, you should pay attention to the battery voltage range and then combine it with the test standards to selec
• Sharing of key points on the use of ADI passive components
  Sharing of key points on the use of ADI passive components
• Four design considerations for telematics hardware in connected cars
  It may surprise you to learn that a technology that has been around for nearly two decades has paved the way for connected cars. ECall is old fashioned by high-tech standards, but it is now mandatory
• Wide voltage input USB-C, 5V/3A output adapter reference design
  USB-C, DFP, 5V/3A output, 85-265VAC input, adapter, low cost reference designThe UCC28700 and TPS25810 are used to provide isolated 5 V at 3 A over the USB type C interface. The UCC28700 performs prim
• When the machine is turned off, the LDO output is normally 3V. Why does the voltage reach 3.5V after the machine is turned on? What is the reason?
• 【Smart Sports Watch】3. Build Development Environment 2
• Ginkgo USB-SPI host mode four data transmission mode timing diagram
• History of the Development of Microwave Circuits
• 6657Statically configure serial port general interrupt in sys/bios

Trending Downloads

• Centrifugal pump and pipeline performance parameter test simulation system based on MATLAB
• Battery Drain Test Solution for Low-Power IoT Devices
• Template project file based on EasyARM2200 development board (applicable to LPC2200 processor)
• AGC Verilog Implementation
• STM32469I_EVAL-DAC
• Master Qt4 Programming.part1
• Generation and detection methods of power grid harmonics
• Starting of three-phase asynchronous motor
• Online monitoring and control of space power distribution systems
• modscan32 Lite

Trending ArticlesMore

• This is an era of looking at faces: facial recognition technology
• Practical information | Detailed analysis of various protection circuit examples of switching power supplies
• An employee was fired for buying glass for Musk, Zhejiang University released its superconducting quantum chip results, GitHub and Google freeze recruitment, more news today here
• Want to do something big? Lenovo cuts 2% of its global workforce, Motorola cuts nearly half of its employees!
• Maxim's Insights | Intelligent power management is the general trend
• DIY Mobile Phone
• Famous Company Recruitment | HiSilicon is looking for you, did you know?
• Useful Information | Why does a diode conduct electricity in one direction?
• The integrated circuit industry became a hot topic at the two sessions for the first time. Let’s see what the representatives said!
• China Telecom, China Mobile, China Unicom, China Broadcasting and Television have obtained 5G licenses, and 5G mobile phones will explode next year