HTTP post request written in pure C

Recommended ContentMore

Open source project More

• CISPR25 automotive taillight reference design based on buck + linear LED driver system
• 51 small system board
• EnDat 2.2 Absolute Encoder Master Interface Reference Design for C2000 MCUs
• NCP3063DFBSTGEVB: DFN Boost Demonstration Evaluation Board
• DER-395 - 14.35 W triac dimmable non-isolated LED driver for PAR30 lamps
• Tai Chi Maker arduboy mini game console
• High-performance power bank PCB based on IP5306 (compatible with IP5307)
• Doraemon PCB
• 18752 amplifier
• Desktop HUB+dial

Searched by Users

• IEC60950 safety standards
• PADS9.3 green Chinese full-featured version + cracking files and methods.part05
• Altium Designer script file PCB Logo Creator download
• Renesas MCU Download Software
• Newland HR100 barcode scanner user manual.pdf
• Several examples of VFP programming and software development are a good helper for learning Visual Foxpro.
• Solar LED Street Light Intelligent Control System Power Control and Load Drive
• Isolated step-up DC transformer based on full-bridge LLC-SRC
• HT16K33 RAM Mapped 16×8 LED Driver with Key Scan
• Altium Designer Summer 09 Download Address Installation Crack Tutorial

Just Take a LookMore

• If you want to make an adjustable power supply yourself, here is the reference tutorial~~~
  I recently wanted to make an adjustable power supply, and then I found some information on the Internet. I'll record it here and share it with netizens who want to make their own.Some homemade videos
• i.mx6ull uses Openwrt system
  Introduction: OpenWrt can be described as an embedded Linux distribution. (Mainstream router firmwares include dd-wrt, tomato, and openwrt.) Compared to a single, static system, OpenWrt's package mana
• May I ask what IDE was used to create the project with the extension MPJ? See the picture below.
  May I ask what IDE was used to create the project with the extension MPJ? See the picture below.
• Please tell me, can this diagram realize a bistable circuit?
  [i=s]This post was last edited by sky999 on 2021-3-8 06:18[/i]Pin 4 of 1308 is the enable pin. It works when it is greater than 1.5V and stops when it is less than 0.4V. I want to achieve output when
• BlueNRG-1 electronic ID card communication
  I want to make an electronic ID card based on BlueNRG-1. I want to send and upload identity data to and from Android. The number of electronic ID cards can be supported to be around 100, all online at
• STM32 MCU realizes serial port 1 (115200) to receive/send data to serial port 2 (9600) at the same time
• "【TGF4042 Signal Generator】" Dual-channel signal measurement
• MSP430F5529 initialization channels and pins
• Design of low voltage dropout buck regulator circuit
• [Development Preparation] Keil routine development for RSL10 development board

Trending Downloads

• AVR MCU Simulation Polar-avr-jtag-ice Technical Manual
• 82C237 pdf datasheet (CMOS High Performance Programmable DMA Controller)
• APA4835a7
• Multifunctional Taxi Meter Based on AT89C51 Single Chip Microcomputer
• PROTEUS Getting Started Tutorial
• High-power three-phase current-source thyristor SVPWM rectifier multi-bridge parallel technology
• This is the solution to the traveling salesman problem in the algorithm. I hope it will be helpful to you.
• Design of small DC electromagnet boost and drive circuit based on SG3525
• XL5003 datasheet
• Research on Fuzzy PID Excitation Controller for Synchronous Generator Based on Genetic Algorithm-2005

Trending ArticlesMore

• Amplifier input impedance parameters and application simulation
• Run, wireless charging!
• Did Intel really lose?
• [Chongqing Station] Registration for Melexis Sensing Technology Tour Seminar is now open!
• common problem
• Apple's most ambitious chip plan yet
• Summary of the Semiconductor Equipment Market in 2020
• ​ADI & Shijian will help you understand chemical analysis and analytical instrument application solutions. Answer questions and win prizes!