T-1 (3mm) SOLID STATE LAMP
Part Number: WP710A10ID14V
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
DISCHARGE
SENSITIVE
DEVICES
High Efficiency Red
Features
Low power consumption.
Popular T-1 diameter package.
General purpose leads.
Reliable and rugged.
Long life - solid state reliability.
Available on tape and reel.
14V internal resistor.
RoHS compliant.
Descriptions
The High Efficiency Red source color devices are made
with Gallium Arsenide Phosphide on Gallium Phosphide
Orange Light Emitting Diode.
Electrostatic discharge and power surge could damage
the LEDs.
It is recommended to use a wrist band or anti-
electrostatic glove when handling the LEDs.
All devices, equipments and machineries must be
electrically grounded.
Package Dimensions
Notes:
1. All dimensions are in millimeters (inches).
2. Tolerance is ±0.25(0.01") unless otherwise noted.
3. Lead spacing is measured where the leads emerge from the package.
4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice.
SPEC NO: DSAL0506
APPROVED: WYNEC
REV NO: V.5A
CHECKED: Allen Liu
DATE: JAN/22/2015
DRAWN: L.Q.Xie
PAGE: 1 OF 6
ERP: 1101029207
Selection Guide
Part No.
Dice
Lens Type
Iv (mcd) [2]
V= 14V
Min.
WP710A10ID14V
High Efficiency Red (GaAsP/GaP)
Red Diffused
10
*5
Typ.
20
*10
Viewing
Angle [1]
2θ1/2
40
°
Notes:
1.
θ1/2
is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value.
2. Luminous intensity/ luminous Flux: +/-15%.
* Luminous intensity value is traceable to the CIE127-2007 compliant national standards.
Electrical / Optical Characteristics at TA=25°C
Symbol
λpeak
λD
[1]
Δλ1/2
I
F
I
R
Parameter
Peak Wavelength
Dominant Wavelength
Spectral Line Half-width
Forward Current
Reverse Current
Device
High Efficiency Red
High Efficiency Red
High Efficiency Red
High Efficiency Red
High Efficiency Red
Typ.
627
617
45
10.5
13.5
10
Max.
Units
nm
nm
nm
mA
uA
Test Conditions
V
F
=14V
V
F
=14V
V
F
=14V
V
F
=14V
V
R
= 5V
Note:
1.Wavelength: +/-1nm.
2.Wavelength value is traceable to the CIE127-2007 compliant national standards.
3.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or
premature failure.
Absolute Maximum Ratings at TA=25°C
Parameter
Power dissipation
Forward Voltage
Reverse Voltage
Operating Temperature
Storage Temperature
Lead Solder Temperature [1]
Lead Solder Temperature [2]
Notes:
1. 2mm below package base.
2. 5mm below package base.
High Efficiency Red
160
16
5
-40°C To +70°C
-40°C To +85°C
260°C For 3 Seconds
260°C For 5 Seconds
Units
mW
V
V
SPEC NO: DSAL0506
APPROVED: WYNEC
REV NO: V.5A
CHECKED: Allen Liu
DATE: JAN/22/2015
DRAWN: L.Q.Xie
PAGE: 2 OF 6
ERP: 1101029207
High Efficiency Red
WP710A10ID14V
SPEC NO: DSAL0506
APPROVED: WYNEC
REV NO: V.5A
CHECKED: Allen Liu
DATE: JAN/22/2015
DRAWN: L.Q.Xie
PAGE: 3 OF 6
ERP: 1101029207
PACKING & LABEL SPECIFICATIONS
WP710A10ID14V
Terms and conditions for the usage of this document
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without
notice. Before production usage customer should refer to the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental
and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible
for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has
special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with
Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. All design applications should refer to Kingbright application notes available at
http://www.KingbrightUSA.com/ApplicationNotes
SPEC NO: DSAL0506
APPROVED: WYNEC
REV NO: V.5A
CHECKED: Allen Liu
DATE: JAN/22/2015
DRAWN: L.Q.Xie
PAGE: 4 OF 6
ERP: 1101029207
SPEC NO: DSAL0506
APPROVED: WYNEC
REV NO: V.5A
CHECKED: Allen Liu
DATE: JAN/22/2015
DRAWN: L.Q.Xie
PAGE: 5 OF 6
ERP: 1101029207
京公网安备 11010802033920号
EEWORLD
