Model 8150
Position Sensor
7/8” Diameter
10 turn* Non-Contacting
Hall Effect
MODEL STYLES AVAILABLE
8151
8153
8154
8156
1/8” Shaft, 1/4” Bushing
1/8” Shaft, Servo Mount
6 mm shaft, 3/8” Bushing
1/4” shaft, 3/8” Bushing
ELECTRICAL
1
Input Voltage
Output Voltage
Output Overvoltage Limits
Output Current
Output Load
Supply Voltage Absolute Limits
Independent Linearity
2
Hysteresis
Resolution
Supply Current
Dielectric Strength
Insulation Resistance
Electrostatic Discharge (ESD)
Bulk Current Injection (BCI)
Actual Electrical Travel
Temperature Coefficient of Output Voltage
4.5 to 5.5 Vdc nominal
0.2 Vdc (4%) to 4.8 Vdc (96%) Typical (see Feature Codes table)
10 Vdc to -0.3 Vdc; output may be shorted to ground or supply without damage
±15 mA maximum
1 kΩ Min., 10 kΩ typical
20 Vdc Max., -10 Vdc minimum
±0.5% (0.25% Available)
10° maximum (10 turn), 5° maximum (5 turn), 3° maximum (3 turn)
0.88° for 3600° travel, 0.44° for 1800° travel, 0.27° for 1080° travel
8.5 mA typical, 12 mA maximum
750 V rms
1,000 MegΩ minimum
Passes 2 kV human body model and 15 kV air discharge
Passes 2-500 MHz at 200 mA
Same as mechanical travel
± 20 ppm/°C
MECHANICAL
Total Mechanical Travel
Bearing
Weight
Panel Nut Tightening Torque
Start/Run Torque (ES option adds 0.5 oz.-in.)
Up to 3600° continuous
Bushing models use bronze sleeve, Servo model uses two ball bearings
TBD
25 in. lb. maximum
< 0.1 oz-in
Specifications subject to change without notice.
Linearity is measured per voltage code range, inset by 1% of input voltage on each end.
* Model available in 3 & 5 turn versions.
1
2
RoHS 2
Pb
compliant
BI Technologies Corporation
4200 Bonita Place, Fullerton, CA 92835 USA
Phone: 714 447 2345
August 18, 2015
Website: www.bitechnologies.com
Model 8150 page 1 of 4
Model 8150
Shock
Vibration
ENVIRONMENTAL
Operating Temperature Range
-40°C to +125°C
Per MIL R-39023, 6 ms Saw-tooth 100 G’s
Per MIL R-39023, 10 G’s, 100 to 500 Hz
Per MIL 202G, Method 106G
all other models: 10 million shaft revolutions with up to 8 oz side load
Storage Temperature Range
Ingress Protection Rating (IP Code)
-55°C to +125°C
IP50, IP66 available as option (feature code ES)
8153: 50 million shaft revolutions with side load < 0.33 lb, 100 million with side load < 0.25 lb
Moisture Resistance, Powered
Rotational Life
ORDERING INFORMATION
8150 V1 T10 L.5 XX
Model Series
Voltage Output Code (see table)
Number of turns (3, 5, and 10 are standard)
Linearity, Independent
Optional Feature Code (see table)
No code required for slotted shaft 8154/8156
or for plain shaft 8151/8153
CODES
Voltage Output Codes
V0
V1
V2
V3
V4
V5
≤ 3% to ≥ 96%
4% to 96%
5% to 95%
10% to 90%
15% to 85%
20% to 80%
no code
SS
FS
LT
SL
CW
HT
ES
When V0 is used the angle specified is
the theoretical angle over which the
output would vary if the output could
actually reach 0% and 100% of Vcc.
Optional Feature Codes
8151, 8153 plain shaft. 8154, 8156 slotted shaft
Slotted Shaft (8151, 8153 only. Not used for 8154, 8156)
Flatted Shaft
Linearity Data
Shaft Lock (8156 only)
Reverse Direction
High Torque (8156 only)
Seal IP66 (8154, 8156 only)
When multiple feature codes are used the P/N shall be in the
same sequence as listed in this table (top to bottom).
BI Technologies Corporation
4200 Bonita Place, Fullerton, CA 92835 USA
Phone: 714 447 2345
August 18, 2015
Website: www.bitechnologies.com
Model 8150 page 2 of 4
Model 8150
MATCHING TURNS COUNTING DIALS
8151: RBJ, 2601, 2641
8154, 8156: RB, 2126, 2606, 2606S, 2607, 2607S, 2626, 2627, 2646, 2646S, 2647, 2647S
OUTLINE DRAWING (bushing mounts)
BI Technologies Corporation
4200 Bonita Place, Fullerton, CA 92835 USA
Phone: 714 447 2345
August 18, 2015
Website: www.bitechnologies.com
Model 8150 page 3 of 4
Model 8150
OUTLINE DRAWING (8153 servo mount)
BI Technologies Corporation
4200 Bonita Place, Fullerton, CA 92835 USA
Phone: 714 447 2345
August 18, 2015
Website: www.bitechnologies.com
Model 8150 page 4 of 4
Domestic Chip Exchange
京公网安备 11010802033920号
EEWORLD
