!Note
• Please read rating and
!CAUTION
(for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Product specifications are as of
August 2016
.
Cap. Table
High Q Monolithic Ceramic Capacitor for High Frequency
GJM Series
Wire bondable vertical electrode Monolithic Ceramic Capacitor
GMA Series
Wire bondable/AuSn solderable Monolithic Ceramic Capacitor
GMD Series
High Q Monolithic Ceramic Capacitor for
High frequency and High power GQM Series
High Effective Capacitance & High Allowable Ripple Current
Monolithic Ceramic Capacitor GR3 Series
Soft termination Monolithic Ceramic Capacitors
GRJ Series
8-Terminal Low ESL Monolithic Ceramic Capacitor
LLA Series
LW Reversed Type Low ESL Monolithic Ceramic Capacitors
LLL Series
10-Terminal Type Low ESL Monolithic Ceramic Capacitor
LLM Series
ESR Controlled Type Low ESL Monolithic Ceramic Capacitors
LLR Series
Metal terminal type monolithic ceramic capacitors
KRM Series
p91
p113
p116
p119
p130
p132
p136
p138
p140
p142
p144
p10
p11
p12
p13
p16
p14
p17
p17
p18
p18
p19
p18
p20
p21
High Effective Capacitance & High Allowable Ripple Current Metal
Terminal Type Monolithic Ceramic Capacitor KR3 Series
p147
3 Terminal Low ESL Monolithic Ceramic Capacitors
NFM Series
Monolithic Ceramic Capacitors for implanted Medical Devices
GCH Series
!Caution/Notice/Soldering
and Mounting
Introduction of Website SimSurfing
Product Information
p150
p152
p156
p185
p186
Please check the MURATA website (http://www.murata.com/)
if you cannot find a part number in this catalog.
!
Caution/Notice/ GCH Series
Soldering Mounting
NFM Series
KR3 Series
KRM Series
LLR Series
LLM Series
LLL Series
LLA Series
GRJ Series
GR3 Series
GQM Series
General Purpose Monolithic Ceramic Capacitors
GRM Series
separate
volume
p24 p1–16
GMD Series
Explanation of Symbols in This Catalog
Selection Guide
Catalog information
Part Numbering
Capacitance Table
p2
p3
p4
p5
p9
GMA Series
GJM Series
Contents
GRM Series
1
!Note
• Please read rating and
!CAUTION
(for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
C02E.pdf
Dec.7,2016
Explanation of Symbols in This Catalog
WEB
Links are provided to the latest information from the PDF version of the catalog, which is available on the web.
For applications that do not require a particular
reliability. such as general equipment.
Infotainment for Automotive
The product for entertainment equipment like car
navigations, car audios, and body control equipment
like wipers, power windows.
Powertrain/Safety for Automotive
Products use for applications (running, turning,
stopping, and safety devices) that particularly concern
human life, such as in devices for automotive.
Medical-grade products for Implanted Medical Devices
These products are intended for use in implanted
medical devices such as cardiac pacemakers, cochlear
implants, insulin pumps, and gastric electrostimulators.
They are suitable for use in non-critical circuits .
*1
*1
Non-critical circuits
This term refers to circuits in implanted medical
devices that are not directly linked to life support, i.e.
circuits that will not directly endanger the life of the
patient should the functionality of the device be
reduced or halted by failure of the circuit.
AEC-Q200 compliant product
Safety Standard Certified Product
Products that acquired safety standard certification
IEC60384-14 and products based on the Electrical
Appliance and Material Safety Law of Japan.
Low dissipation for high frequency
By devising ceramic materials and electrode materials,
low dissipation is achieved in frequency bands of VHF,
UHF, and microwave or beyond.
Low inductance
This capacitor is designed so that the parasitic
inductance component (ESL) that the capacitor has on
the high frequency side becomes lower.
Fail safe product
This capacitor is designed to prevent failures as much
as possible by short mode.
Product resistant to deflection cracking
This capacitor is designed to prevent failures as much
as possible by short mode caused by cracking when
there is board deflection.
Product with solder cracking suppression
This capacitor is configured with metal terminals and
leads connected to the chip. The metal terminals and
leads relieve the stress from expansion and contraction
of the solder, to suppress solder cracking.
Product suitable for acoustic noise reduction and low
distortion
This product suppresses acoustic noise, which occurs
when a ceramic capacitor is used, by devising the
materials and configuration.
No DC bias characteristics
Polymer capacitor is no capacitance change with DC bias
due to aluminum oxidized film for dielectric.
Low-inductance product suitable for noise suppression.
This product has extremely low ESL and is suitable for
suppression of noise, including high frequencies.
This product can also be used as a low-ESL,
high-performance bypass capacitor.
Product for bonding
Since gold is used for the external electrodes, the
capacitor can be mounted by die bonding/wire bonding.
Derating 1
This product is suitable when a voltage continuously
applied to a capacitor in an operating circuit, is used
below (derated) the rated voltage of the capacitor. This
model guarantees the test conditions in the endurance
test, at a rated voltage x 100% at the maximum
operating temperature. A reliability assurance level
equivalent to a common product can be secured, by
using this product within the voltage and temperature
derated conditions recommended in the figure below.
Recommended Conditions of the Derating Operating Voltage and Temperature
Operating Voltage/Rated Voltage (%)
120
100
125°C Type
80
60
40
20
0
0
25
50
75
100
125
150
105°C Type
85°C Type
Product Temperature (°C)
Derating 2
When the product temperature exceeds 105°C, please
use this product within the voltage and temperature
derated conditions in the figure below.
700
Rated Voltage 630V
600
500
Rated Voltage (%)
(450V)
400
(350V)
Rated Voltage 450V
300
200
100
0
0
25
50
75
100
125
150
Product Temperature (°C)
Derating 3
Please apply the derating curve according to the
operating temperature.
Please refer to detailed specifications sheet for details.
2
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
