PW172KB
Universal 15 – 19 Watt Series
ITE Switch-Mode Power Supply
•
100-240VAC Universal Input
•
Desktop and Wall-Plug Style with either fixed blades, or
3 Year Warranty
Interchangeable Blades* ( Kit sold separately)
•
5V to 48V Single Output Models, up to 19W
•
Modified and Custom Designs Available
•
Regulated Output with Low Ripple
•
Impact-Resistant Polycarbonate Enclosure
•
No load Power Consumption < 0.5W
•
Meets EISA Requirements (see next page for details).
•
Meets Energy Star Level IV
Specifications
All Specifications are typical at nominal input, full load at 25
°
C unless otherwise stated.
MTBF
>100,000 hours (calculated)
Hold-up Time
18 ms min. @ 115VAC
Overvoltage Protection
Built-in
Overload Protection
Hiccup Mode
Short Circuit Protection
Hiccup Mode
Topology
Switching – Fixed Frequency Flyback
Approvals and Safety Standards
EN/IEC/CSA/UL60950-1, EMC: EN55022/55024/61000
Dielectric Withstand
Input-Output: 3000VAC, Input-GND: 1500VAC, Output-GND: 500VDC
Operating Temperature
0° to 40°C, no derating
Storage Temperature
-30 to +85°C.
Relative Humidity
5% to 95%, non-condensing
Altitude
0 to 10,000 ft.
Output Connections:
Cable: 18AWG, 1800mm (5V & 6V models: 1500mm), 2 conductor.
Connector: 2.5mm barrel type (Ault #3) connector, center contact (+).
Other connector options are available.
AC Input
100-240VAC, -/-10% (class I), +6%, -10% (class II), 47-63 Hz, 1∅.
Input Current
90VAC: 0.5A
Inrush Current
Inrush limiting provided.
Input Fuses
Internal Primary Current Fuse is provided.
Efficiency
Meet EISA Requirements – see page 2
Output Voltage
See chart.
Output Power
See chart
Ripple and Noise
1% pk-pk max., 20MHz BW
Line & Load Voltage Regulation
Excluding Cord: Line: +/- 1%, Load: +/-5%.
Transient Response
500µs max., 50% load step, typical
Minimum Load
Not required.
Case Material:
Black 94V0 Polycarbonate
Case Dimensions:
See outline drawing.
Model Number Key
PW172 K B 12 03 F 01
Modification Designator. "01" is standared part, "02" and higher denotes a modified model.
Input Receptacle. See Below for options. "F" receptacle (IEC320, C14 type, grounded) noted above.
Output Connector. "03" connector is standard. Other output connectors available. Contact the factory for more details
Output Voltage
Design Revision Changes
Manufacturing Location
Product Family
______________________________________________________________________________________________________________________________
SL Power Electronics Corp
•
6050 King Drive Ventura, CA 93003
•
Phone 805.486.4565
•
Fax 858.712.2040
•
Email: info@slpower.com
•
www.slpower.com
1 of 3
PW172KB
Universal 15-19 Watt Series
ITE Switch Mode Power Supply
3 Year Warranty
Model Number
PW172KB0503F01
PW172KB0603F01
PW172KB0903F01
PW172KB1203F01
PW172KB1503F01
PW172KB1803F01
PW172KB2403F01
PW172KB4803F01
Volts (V)
5V
6V
9V
12 V
15 V
18 V
24 V
48 V
Output Current (max)
3.00 A
2.50 A
2.00 A
1.50 A
1.20 A
1.00 A
0.75 A
0.40 A
Max Watts
15.0 W
15.0 W
18.0 W
18.0 W
18.0 W
18.0 W
18.0 W
19.2 W
Ripple (Vp-p max)
50mV
60mV
90mV
120mV
150mV
180mV
240mV
480mV
Note: Part numbers above include #3 output connector and IEC320 C14 grounded input receptacle. See below for other options.
Input Receptacle Options
DESKTOP OPTIONS
WALL-PLUG OPTIONS
Output Connector
IEC320
C14
Grounded
IEC320
C18
Ungrounded
IEC320
C8
"Shaver"
N. America
Japan
Interchangeable
N. America
Japan
Fixed
Europe
Fixed
United
Kingdom
Fixed
Australia
Fixed
(F)
Notes:
(Q)
(N)
(B)
(C)
(M)
(G)
(H)
Notes:
1. For Desktop options, choose the applicable letter above.
2. For Wall-plug options, choose the applicable letter above. The model will then be fitted only with the
receptacle chosen. The North American blade version (B) will be an interchangeable blade. The other
options (C), (M), (G), and (H), will be fixed blades molded in the case.
3. Blade Kit is available which will include one each of a EU, UK, and Aust blade. Kit part number is
KT1027K . Can be used with (B) version only, to allow blades to be interchanged.
1 Ault #3 Connector
2. Center Contact = Positive
3. Connector is Switchcraft 760 plug or equivalent.
4. Suggested Mating Connector is Switchcraft 712A jack or
equivalent.
5. Other output connector options are available. Contact your
local representative for details.
2007 Energy Independence and Security Act - EISA
The Energy Independence and Security Act of 2007 was passed in December of 2007 and addresses minimum efficiency standards and standby
levels for Class A external power supplies that are 250 Watts and under. This law stipulates that external power supplies manufactured on July 1,
2008 and beyond meet certain minimum efficiency and standby criteria as defined below.
Minimum Efficiency Criteria:
Active mode is defined as when a power supply’s input is connected to a line voltage AC and it’s output is connected to a DC or AC load, drawing a
portion of the product’s power output. Depending upon the power rating for the power supply, it must meet the minimum efficiency criteria outlined
below.
Energy-Efficiency Criteria for Active Mode:
Output Power on Adapter Label
0 to < 1 Watt
> 1 watt to
≤
51 watts
> 51 watts
Minimum Average Efficiency Percentage
≥
0.50 * output power on the label
≥
[0.09 * Ln (output power on adapter label)] + 0.50
≥
0.85
Energy Consumption Criteria for No Load Mode:
The power supply must also meet a requirement for when its input is connected to line voltage AC but its output is not connected to a load.
Depending upon the power output of the supply, it must keep its energy consumption below the following values:
Output Power on Adapter Label
Maximum Power Consumption in No-Load Mode
0 to < 250 Watts
≤
0.50 watts
2 of 3
______________________________________________________________________________________________________________________________
SL Power Electronics Corp
•
6050 King Drive Ventura, CA 93003
•
Phone 805.486.4565
•
Fax 858.712.2040
•
Email: info@slpower.com
•
www.slpower.com
PW172KB
Universal 15-19 Watt Series
ITE Switch Mode Power Supply
3 Year Warranty
Outline Drawings
Dimensions are in mm
Desktop Style
(Option “F” shown)
Wallplug Style
(Option “B” shown)
Data Sheet © 2009 SL Power Electronics Corp. The information and specifications contained herein are believed to be correct at the time of publication.
Rev. 8-10-2009
However, SL Power accepts no responsibility for consequences arising from reproduction errors or inaccuracies. Specifications are subject to change without notice.
3 of 3
______________________________________________________________________________________________________________________________
SL Power Electronics Corp
•
6050 King Drive Ventura, CA 93003
•
Phone 805.486.4565
•
Fax 858.712.2040
•
Email: info@slpower.com
•
www.slpower.com
京公网安备 11010802033920号
EEWORLD
