HV2116
8-Channel High Voltage Analog Switch
Ordering Information
Package Options
V
PP
– V
NN
160V
28-lead plastic
chip carrier
HV2116PJ
Die
HV2116X
Features
ETE –
SOL
General Description
– OB
Not recommended for new designs. Please use HV202
instead.
This device is an 8-channel high-voltage analog switch integrated
circuit (IC) intended for use in applications requiring high voltage
switching controlled by low voltage control signals, such as ultra-
sound imaging and printers. Input data is shifted into an 8-bit shift
register which can then be retained in an 8-bit latch. To reduce
any possible clock feedthrough noise, Latch Enable (LE) should
be left high until all bits are clocked in. Using HVCMOS technol-
ogy, this switch combines high voltage bilateral DMOS switches
and low power CMOS logic to provide efficient control of high
voltage analog signals.
This IC is suitable for various combinations of high voltage sup-
plies, e.g., for HV2116 +40V/-120V, or +80V/-80V or +150V/-10V.
■
HVCMOS
®
technology for high performance
■
Very low quiescent power dissipation – 10µA
■
Output On-resistance typically 22 ohms
■
Low parasitic capacitances
■
DC to 10MHz analog signal frequency
■
-50dB typical output off isolation at 5MHz
■
CMOS logic circuitry for low power
■
Excellent noise immunity
■
On-chip shift register, and latch logic circuitry
■
Flexible high voltage supplies
■
Surface mount package available
13
13
Absolute Maximum Ratings*
V
DD
logic power supply voltage
V
PP
- V
NN
supply voltage
V
PP
positive high voltage supply
V
NN
Negative high voltage supply
Logic input voltages
Analog signal range
Peak analog signal current/channel
Storage temperature
Power dissipation
-0.5V to +18V
174V
-0.5V to +160V
+0.5V to -160V
-0.5V to V
DD
+0.3V
V
NN
to V
PP
3.0A
-65°C to +150°C
1.2W
*Absolute Maximum Ratings are those values beyond which damage to the
device may occur. Functional operation under these conditions is not implied.
Continuous operation of the device at the absolute rating level may affect
device reliability.
13-57
TE –
Electrical Characteristics
SOLE
– OB
AC Characteristics
(over operating conditions V
DD
= 15V, unless otherwise noted)
Characteristics
Time to Turn Off V
SIG
*
Set Up Time Before LE Rises
Time Width of LE
Clock Delay Time to Data Out
Set Up Time Data to Clock
Hold Time Data from Clock
Clock Freq
Turn On Time
Turn Off Time
Sym
t
SIG(OFF)
t
SD
t
WLE
t
DO
t
SU
t
h
f
CLK
15
35
3.0
2.0
3.0
10
Maximum V
SIG
Slew Rate
dv/dt
10
10
Off Isolation
KO
-30
-45
Switch Crosstalk
Output Switch Isolation
Diode Current
Off Capacitance SW to GND
On Capacitance SW to GND
K
CR
I
ID
C
SG(OFF)
C
SG(ON)
5.0
25
-60
300
17
50
5.0
25
12
38
-30
-45
-60
-33
-50
-70
300
17
50
5.0
25
150
150
300
15
35
3.0
2.0
3.0
10
10
10
-30
-45
-60
300
17
50
0
°
C
min
max
min
200
150
150
150
8.0
330
20
35
3.0
2.0
3.0
10
10
10
dB
dB
dB
mA
pF
pF
V/ns
150
150
350
+25
°
C
typ
max
min
+70
°
C
max
Units
ns
ns
ns
ns
ns
ns
MHz
µs
µs
HV2116
Test Conditions
50% duty cycle
f
DATA
= f
CLK
/2
V
SIG
= V
PP
-10V,
R
L
= 10KΩ
V
SIG
= V
PP
-10V,
R
L
= 10KΩ
V
PP
= 150V,
V
NN
= -10V
V
PP
= 80V,
V
NN
= -80V
V
PP
= 40V,
V
NN
= -120V
f = 5MHz,
1KΩ//15pF load
f = 5MHz,
50Ω load
f = 5MHz,
50Ω load
300ns pulse width,
2.0% duty cycle
0V, 1MHz
0V, 1MHz
*Time required for analog signal to turn off before output switch turns off (critical timing).
13
13
13-59
HV2116
Electrical Characteristics
AC Characteristics
(over operating conditions V
DD
= 15V, unless otherwise noted)
Characteristics
Sym
+V
SPK
-V
SPK
Output Voltage Spike
+V
SPK
-V
SPK
+V
SPK
-V
SPK
Charge Injection
Q
+25
°
C
min
typ
1.0
3.5
12
18
6.0
9.0
1700
850
600
pC
V
max
Units
Test Conditions
V
PP
= 40V, V
NN
= -120V
R
L
= 50Ω
V
PP
= 80V, V
NN
= -80V
R
L
= 50Ω
V
PP
= 150V, V
NN
= -10V
R
L
= 50Ω
V
PP
= 80V, V
NN
= -80V, V
SIG
= 0V
V
PP
= 80V, V
NN
= -80V, V
SIG
= 70V
V
PP
= 80V, V
NN
= -80V, V
SIG
= -70V
TE –
SOLE
– OB
Operating Conditions
Symbol
V
DD
V
PP
V
NN
V
IH
V
IL
V
SIG
T
A
Parameter
Logic power supply voltage
1, 3
Positive high voltage supply
1, 3
Negative high voltage supply
1, 3
High-level input voltage
Low-level input voltage
Analog signal voltage peak to peak
2
Operating free air-temperature
Value
10.0 V to 15.5 V
40V to V
NN
+ 160V
-10.0V to -120V
V
DD
-2V to V
DD
0V to 2.0V
V
NN
+10V to V
PP
-10
0°C to 70°C
Notes:
1 Power up/down sequence is arbitrary except GND must be powered-up first and powered-down last.
2 V
SIG
must be V
NN
≤
V
SIG
≤
V
PP
or floating during power up/down transistion.
3 Rise and fall times of power supplies V
DD
, V
PP
, and V
NN
should not be less than 1.0msec.
13-60