DS2405V datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > storage> storage> DS2405V

DS2405V: DescriptionSPECIALTY MEMORY CIRCUIT, PDSO6; Categorystorage storage; File Size219KB，15 Pages; ManufacturerDALLAS; Websitehttp://www.dalsemi.com

Download Datasheet Parametric Compare View All

DS2405V Overview

SPECIALTY MEMORY CIRCUIT, PDSO6

DS2405V Parametric

Parameter Name	Attribute value
Maker	DALLAS
package instruction	TSOC-6
Reach Compliance Code	unknow
JESD-30 code	R-PDSO-C6
memory density	64 bi
Memory IC Type	MEMORY CIRCUIT
memory width	1
Number of functions	1
Number of terminals	6
word count	64 words
character code	64
Operating mode	ASYNCHRONOUS
Maximum operating temperature	85 °C
Minimum operating temperature	-40 °C
organize	64X1
Package body material	PLASTIC/EPOXY
Package shape	RECTANGULAR
Package form	SMALL OUTLINE
Certification status	Not Qualified
Maximum supply voltage (Vsup)	6 V
Minimum supply voltage (Vsup)	2.8 V
surface mount	YES
technology	CMOS
Temperature level	INDUSTRIAL
Terminal form	C BEND
Terminal location	DUAL

Preview

Download Datasheet

View All

DS2405

Addressable Switch

www.dalsemi.com

FEATURES

Open drain PIO pin is controlled by

matching 64-bit, laser-engraved registration

number associated with each device

Logic level of open drain output can be

determined over 1-Wire bus for closed-loop

control

PIO pin sink capability is greater than 4 mA

at 0.4V

Multiple DS2405’ can be identified on a

common 1-Wire bus and be turned on or off

independent of other devices on the bus

Unique, factory-lasered and tested 64-bit

registration number (8-bit family code +48-

bit serial number +8-bit CRC tester) assures

absolute identity because no two parts are

alike

Built-in multidrop controller ensures

compatibility with other MicroLAN products

Reduces control, address, data, and power to

a single data pin

Directly connects to a single port pin of a

microprocessor and communicates at up to

16.3 kbits/s

8-bit family code specifies DS2405

communications requirements to reader

8-bit cyclic redundancy check ensures error-

free selection

Zero standby power required

Low cost TO-92, SOT-223, or 6-pin TSOC

surface mount package

1-Wire communication operates over a wide

voltage range of 2.8V to 6.0V from -40°C to

+85°C

PIN ASSIGNMENT

TSOC PACKAGE

TO-92

DS2405

GND

DATA

PIO

TOP VIEW

3.7 X 4.0 X 1.5

1 2 3

TOP VIEW

BOTTOM VIEW

See Mech.

Drawings Section

PIN DESCRIPTION TSOC

Pin 1

Pin 2

Pin 3

Pin 4

- Ground

- Data

- PIO

- Ground

Pin 1

Pin 2

Pin 3

Pin 4-6

- Ground

- Data

- PIO

-No Connect

1 of 15

102299

DS2405

ORDERING INFORMATION

DS2405

DS2405Z

DS2405P

DS2405T

DS2405Y

DS2405V

TO-92 package

4-pin SOT-223 package

6-pin TSOC package

Tape & Reel version of DS2405

Tape & Reel version of DS2405Z

Tape & Reel version of DS2405P

DESCRIPTION

The DS2405 Addressable Switch is an open drain N-channel transistor that can be turned on or off by

matching the 64-bit factory-lasered registration number within each part. The 64-bit number consists of

an 8-bit family code, a unique 48-bit serial number, and an 8-bit cyclic redundancy check.

Communication with the DS2405 follows the standard Dallas Semiconductor 1-Wire protocol and can be

accomplished with a single port pin of a microcontroller. Multiple DS2405 devices can reside on a

common 1-Wire bus creating a MicroLAN. The network controller circuitry is embedded within the chip

including a search algorithm to determine the identity of each DS2405 on the network. The open drain

output (PIO pin) for each DS2405 on the MicroLan can be independently toggled on or off whether there

is one or many devices sharing the same 1-Wire bus. The logic level of the PIO pin for each device on the

MicroLan can also be individually sensed and reported to the bus master.

OVERVIEW

The DS2405 Addressable Switch provides a means for assigning an electronically readable identification

to a particular node or location with additional control capability provided by an open drain N-channel

MOSFET that can be remotely switched and sensed via communication over the 1-Wire bus. The DS2405

contains a factory-lasered registration number that includes a unique 48-bit serial number, an 8-bit CRC,

and an 8-bit family code (05h). The 64-bit ROM portion of the DS2405 not only creates an absolutely

unique electronic identification for the device itself but also is a means to locate and change or obtain the

state of the switch that is associated with the 64-bit ROM. The structure of the 64-bit ROM is shown in

Figure 1. The device derives its power entirely from the 1-Wire bus by storing energy on an internal

capacitor during periods of time when the signal line is high and continues to operate off of this “parasite”

power source during the low times of the 1-Wire line until it returns high to replenish the parasite

(capacitor) supply. The DS2405 uses the standard Dallas Semiconductor 1-Wire protocol for data

transfers, with all data being read and written least significant bit first. Communication to and from the

DS2405 requires a single bidirectional line that is typically the port pin of the microcontroller. The 1-

Wire bus master (microcontroller) must first issue one of five ROM function commands: 1) Read ROM,

2) Match ROM, 3) Search ROM, 4) Skip ROM, and 5) Active-Only Search ROM. These commands

operate on the 64-bit lasered ROM portion of each device and can singulate a specific device if many are

present on the 1-Wire line as well as indicate to the bus how many and what type of each device is

present. The protocol required for these ROM function commands is described in Figure 4. After a ROM

function command is successfully executed, the open drain output can be toggled or its current status

determined via the 1-Wire bus.

1-WIRE BUS SYSTEM

The 1-Wire bus is a system which has a single bus master and one or more slaves. In all instances, the

DS2405 is a slave device. The bus master is typically a microcontroller. The discussion of this bus system

is broken down into three topics: hardware configuration, transaction sequence, and 1-Wire signaling

(signal type and timing). For a more detailed protocol description, refer to Chapter 4 of the Book of

DS19xx iButton Standards.

2 of 15

102299

DS2405

ROM FUNCTION COMMANDS

Once the bus master has detected a presence, it can issue one of five ROM function commands. All ROM

function commands are 8 bits long. A list of these commands follows (refer to flowchart in Figure 4):

Read ROM [33h]

This command allows the bus master to read the DS2405’ 8-bit family code, unique 48-bit serial

number, and 8-bit CRC. This command can be used only if there is a single DS2405 on the bus. If more

than one slave is present on the bus, a data collision will occur when all slaves try to transmit at the same

time (open drain will produce a wired-AND result).

Match ROM [55h]

The Match ROM command, followed by a 64-bit ROM sequence, allows the bus master to address a

specific device on a multidrop bus. All devices that do not match the 64-bit ROM sequence will wait for a

Reset Pulse. The DS2405 that exactly matches the 64-bit ROM sequence will toggle the state of its PIO

pin after the 64

bit of the match is entered. If the open drain N-channel device was off, it will be turned

on and vice versa. After the last bit of the ROM sequence is received from the bus master and the PIO pin

of the selected DS2405 has toggled, additional read time slots issued by the bus master will cause the

DS2405 to output the logic state of its PIO pin onto the 1-Wire bus. If the pulldown is on and the PIO pin

is a logical 0, the DS2405 will respond with read-0 time slots. If the pulldown is off and the PIO pin is a

logical 1 (external pullup is required), the DS2405 will respond with read-1 time slot. Each additional

read time slot issued by the bus master will continue to indicate the state of the PIO pin until a Reset

Pulse is received from the bus master.

Search ROM [F0h]

When a system is initially interrogated, the bus master may not know the number of devices on the 1-

Wire bus or their 64-bit ROM codes. The Search ROM command allows the bus master to use a process

of elimination to identify the 64-bit ROM codes of all slave devices on the bus. This process of

elimination involves repeated application of a simple three-step procedure where the bus master starts by

reading a bit position in the 64-bit ROM, followed by reading the complement of that bit position, and

finally writing to all the devices still involved in the search the desired logic value for that bit position. An

example is shown below and a flowchart for the search algorithm can be found in the “Book of DS19xx

iButton Standards.”

Four devices are connected to the 1-Wire bus. Their binary ROM contents are:

device 1: xxxxxx10101100

device 2: xxxxxx01010101

device 3: xxxxxx10101111

device 4: xxxxxx10001000

The x’ represent the higher remaining bits. Shown are the lowest 8 bits of the ROM contents. The least

significant bit is to the right in this representation. The search process runs as follows:

1. The master begins the initialization sequence by issuing a Reset Pulse. The devices respond by issuing

Presence Pulses.

2. The master will then issue the Search ROM command on the 1-Wire bus.

5 of 15

102299

DS2405V Related Products

	DS2405V	DS2405T	DS2405Y
Description	SPECIALTY MEMORY CIRCUIT, PDSO6	SPECIALTY MEMORY CIRCUIT, PDSO6	SPECIALTY MEMORY CIRCUIT, PDSO6
Maker	DALLAS	DALLAS	DALLAS
package instruction	TSOC-6	TO-92, 3 PIN	SOT-223, 4 PIN
Reach Compliance Code	unknow	unknow	unknow
JESD-30 code	R-PDSO-C6	O-PBCY-T3	R-PDSO-G4
memory density	64 bi	64 bi	64 bi
Memory IC Type	MEMORY CIRCUIT	MEMORY CIRCUIT	MEMORY CIRCUIT
memory width	1	1	1
Number of functions	1	1	1
Number of terminals	6	3	4
word count	64 words	64 words	64 words
character code	64	64	64
Operating mode	ASYNCHRONOUS	ASYNCHRONOUS	ASYNCHRONOUS
Maximum operating temperature	85 °C	85 °C	85 °C
Minimum operating temperature	-40 °C	-40 °C	-40 °C
organize	64X1	64X1	64X1
Package body material	PLASTIC/EPOXY	PLASTIC/EPOXY	PLASTIC/EPOXY
Package shape	RECTANGULAR	ROUND	RECTANGULAR
Package form	SMALL OUTLINE	CYLINDRICAL	SMALL OUTLINE
Certification status	Not Qualified	Not Qualified	Not Qualified
Maximum supply voltage (Vsup)	6 V	6 V	6 V
Minimum supply voltage (Vsup)	2.8 V	2.8 V	2.8 V
surface mount	YES	NO	YES
technology	CMOS	CMOS	CMOS
Temperature level	INDUSTRIAL	INDUSTRIAL	INDUSTRIAL
Terminal form	C BEND	THROUGH-HOLE	GULL WING
Terminal location	DUAL	BOTTOM	DUAL

Recommended Resources

Simple transistor relay delay pull-in circuit diagram

Computer AC power monitoring circuit

Auto-decompression starting circuit

High level water storage container water level control circuit

GZ-2 bone hyperplasia treatment machine circuit

875p computer motherboard circuit diagram_078

Guo Tianxiang's New Concept 51 MCU C language tutorial. Getting started, improving, and developing: I found that the documents in various forums either could not be opened after downloading, or required a password or had to be purchased from Taobao. I searched for half a day and found this high-qual...; 175的大V MCU

Design and Verification: Verilog HDL: ...; 至芯科技FPGA大牛 FPGA/CPLD

EEWORLD University - How Semiconductors Change the World: How semiconductors change the world : https://training.eeworld.com.cn/course/5653Talking about how semiconductors affect the world...; 木犯001号 Analog electronics

【GD32450I-EVAL】+10SD card test: [i=s]This post was last edited by DDZZ669 on 2020-10-17 21:37[/i]SD card, namely Secure Digital card (Secure Digital), GD32's SDIO interface can be used to drive SD card. In addition, SDIO also define...; DDZZ669 GD32 MCU

3232 Unable to communicate: When I connect the 3232 device at the other end, the waveform is distorted. What is the reason?...; tangwei8802429 Analog electronics

Question about current amplifier: I would like to ask what the load current and load voltage in the book Circuit Design Based on Arithmetic Units and Analog Integrated Circuits mean. I can't understand why the simulation results I got...; sunboy25 Analog electronics

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components