are trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other words and logos identified as
trademarks or service marks are the property of their respective holders as described at
www.altera.com/common/legal.html.
Altera warrants performance of its
semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and
services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service
described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device specifications before relying
on any published information and before placing orders for products or services.
ISO
9001:2008
Registered
Cyclone III Device Handbook
Volume 2
July 2012
Subscribe
1–2
Chapter 1: Cyclone III Device Datasheet
Electrical Characteristics
1
Conditions beyond those listed in
Table 1–1
cause permanent damage to the device.
Additionally, device operation at the absolute maximum ratings for extended periods
of time has adverse effects on the device.
Table 1–1. Cyclone III Devices Absolute Maximum Ratings
Symbol
V
CCINT
V
CCIO
V
CCA
V
CCD_PLL
V
I
I
OUT
V
ESDHBM
V
ESDCDM
T
STG
T
J
Parameter
Supply voltage for internal logic
Supply voltage for output buffers
Supply voltage (analog) for phase-locked loop
(PLL) regulator
Supply voltage (digital) for PLL
DC input voltage
DC output current, per pin
Electrostatic discharge voltage using the human
body model
Electrostatic discharge voltage using the
charged device model
Storage temperature
Operating junction temperature
(1)
Min
–0.5
–0.5
–0.5
–0.5
–0.5
–25
—
—
–65
–40
Max
1.8
3.9
3.75
1.8
3.95
40
±2000
±500
150
125
Unit
V
V
V
V
V
mA
V
V
°C
°C
Note to
Table 1–1:
(1) Supply voltage specifications apply to voltage readings taken at the device pins with respect to ground, not at the
power supply.
Maximum Allowed Overshoot or Undershoot Voltage
During transitions, input signals may overshoot to the voltage listed in
Table 1–2
and
undershoot to –2.0 V for a magnitude of currents less than 100 mA and for periods
shorter than 20 ns.
Table 1–2
lists the maximum allowed input overshoot voltage and
the duration of the overshoot voltage as a percentage over the lifetime of the device.
The maximum allowed overshoot duration is specified as percentage of high-time
over the lifetime of the device.
Cyclone III Device Handbook
Volume 2
July 2012 Altera Corporation
Chapter 1: Cyclone III Device Datasheet
Electrical Characteristics
1–3
1
A DC signal is equivalent to 100% duty cycle. For example, a signal that overshoots to
4.2 V can only be at 4.2 V for 10.74% over the lifetime of the device; for device lifetime
of 10 years, this amounts to 10.74/10ths of a year.
Table 1–2. Cyclone III Devices Maximum Allowed Overshoot During Transitions over a 10-Year
Time Frame
(1)
Symbol
Parameter
Condition
V
I
= 3.95 V
V
I
= 4.0 V
V
I
= 4.05 V
V
I
= 4.10 V
V
I
= 4.15 V
V
I
= 4.20 V
V
i
AC Input
Voltage
V
I
= 4.25 V
V
I
= 4.30 V
V
I
= 4.35 V
V
I
= 4.40 V
V
I
= 4.45 V
V
I
= 4.50 V
V
I
= 4.60 V
V
I
= 4.70 V
Note to
Table 1–2:
(1)
Figure 1–1
shows the methodology to determine the overshoot duration. In the example in
Figure 1–1,
overshoot
voltage is shown in red and is present on the input pin of the Cyclone III device at over 4.1 V but below 4.2 V. From
Table 1–1,
for an overshoot of 4.1 V, the percentage of high time for the overshoot can be as high as 31.97% over
a 10-year period. Percentage of high time is calculated as ([delta T]/T) × 100. This 10-year period assumes the
device is always turned on with 100% I/O toggle rate and 50% duty cycle signal. For lower I/O toggle rates and
situations in which the device is in an idle state, lifetimes are increased.
Overshoot Duration as % of High Time
100
95.67
55.24
31.97
18.52
10.74
6.23
3.62
2.1
1.22
0.71
0.41
0.14
0.047
Unit
%
%
%
%
%
%
%
%
%
%
%
%
%
%
Figure 1–1
shows the methodology to determine the overshoot duration.
Figure 1–1. Cyclone III Devices Overshoot Duration
4.2 V
4.1 V
3.3 V
ΔT
T
July 2012
Altera Corporation
Cyclone III Device Handbook
Volume 2
1–4
Chapter 1: Cyclone III Device Datasheet
Electrical Characteristics
Recommended Operating Conditions
This section lists the functional operation limits for AC and DC parameters for
Cyclone III devices. The steady-state voltage and current values expected from
Cyclone III devices are provided in
Table 1–3.
All supplies must be strictly monotonic
without plateaus.
Table 1–3. Cyclone III Devices Recommended Operating Conditions
Symbol
V
CCINT
(3)
(1), (2)
Parameter
Supply voltage for internal logic
Supply voltage for output buffers, 3.3-V
operation
Supply voltage for output buffers, 3.0-V
operation
Supply voltage for output buffers, 2.5-V
operation
Supply voltage for output buffers, 1.8-V
operation
Supply voltage for output buffers, 1.5-V
operation
Supply voltage for output buffers, 1.2-V
operation
Conditions
—
—
—
—
—
—
—
—
—
—
—
For commercial use
For industrial use
For extended temperature
For automotive use
Standard power-on reset
(POR)
(5)
Fast POR
(6)
Min
1.15
3.135
2.85
2.375
1.71
1.425
1.14
2.375
1.15
–0.5
0
0
–40
–40
–40
50 µs
50 µs
—
Typ
1.2
3.3
3
2.5
1.8
1.5
1.2
2.5
1.2
—
—
—
—
—
—
—
—
—
Max
1.25
3.465
3.15
2.625
1.89
1.575
1.26
2.625
1.25
3.6
V
CCIO
85
100
125
125
50 ms
3 ms
10
Unit
V
V
V
V
V
V
V
V
V
V
V
°C
°C
°C
°C
—
—
mA
V
CCIO
(3), (4)
V
CCA
(3)
(3)
Supply (analog) voltage for PLL
regulator
Supply (digital) voltage for PLL
Input voltage
Output voltage
V
CCD_PLL
V
I
V
O
T
J
Operating junction temperature
t
RAMP
Power supply ramp time
Magnitude of DC current across
PCI-clamp diode when enabled
I
Diode
—
Notes to
Table 1–3:
(1) V
CCIO
for all I/O banks must be powered up during device operation. All V
CCA
pins must be powered to 2.5 V (even when PLLs are not used), and
must be powered up and powered down at the same time.
(2) V
CCD_PLL
must always be connected to V
CCINT
through a decoupling capacitor and ferrite bead.
(3) The V
CC
must rise monotonically.
(4) All input buffers are powered by the V
CCIO
supply.
(5) POR time for Standard POR ranges between 50–200 ms. Each individual power supply should reach the recommended operating range within
50 ms.
(6) POR time for Fast POR ranges between 3–9 ms. Each individual power supply should reach the recommended operating range within 3 ms.
Cyclone III Device Handbook
Volume 2
July 2012 Altera Corporation
Chapter 1: Cyclone III Device Datasheet
Electrical Characteristics
1–5
DC Characteristics
This section lists the I/O leakage current, pin capacitance, on-chip termination (OCT)
tolerance, and bus hold specifications for Cyclone III devices.
Supply Current
Standby current is the current the device draws after the device is configured with no
inputs or outputs toggling and no activity in the device. Use the Excel-based early
power estimator (EPE) to get the supply current estimates for your design because
these currents vary largely with the resources used.
Table 1–4
lists I/O pin leakage
current for Cyclone III devices.
f
For more information about power estimation tools, refer to the
PowerPlay Early Power
Estimator User Guide
and the
PowerPlay Power Analysis
chapter in the
Quartus II
Handbook.
Table 1–4. Cyclone III Devices I/O Pin Leakage Current
(1),
Symbol
I
I
I
OZ
Parameter
Input pin leakage current
Tristated I/O pin leakage
current
Conditions
V
I
= 0 V to V
CCIOMAX
V
O
= 0 V to V
CCIOMAX
(2)
Min
–10
–10
Typ
—
—
Max
10
10
Unit
A
A
Notes to
Table 1–4:
(1) This value is specified for normal device operation. The value varies during device power-up. This applies for all
V
CCIO
settings (3.3, 3.0, 2.5, 1.8, 1.5, and 1.2 V).
(2) 10
A
I/O leakage current limit is applicable when the internal clamping diode is off. A higher current can be the
observed when the diode is on.
Bus Hold
Bus hold retains the last valid logic state after the source driving it either enters the
high impedance state or is removed. Each I/O pin has an option to enable bus hold in
user mode. Bus hold is always disabled in configuration mode.
Table 1–5
lists bus hold specifications for Cyclone III devices.
Suppose a coil is wound on a C-shaped iron core, with the cross-sections of the two ends of the core parallel. After power is applied, does the external magnetic field concentrate in the space between...
[i=s]This post was last edited by VincentLee90 on 2019-5-18 22:49[/i] [align=left][size=14px][font=Tahoma][size=3]Some friends asked me how to design a filter with gain before? What if the normalized ...
I am using Altium Designer to design a Ku-band PCB. The chip package size is relatively small, and the spacing between pads is also small. If I import the schematic directly into the PCB, I will find ...
I originally wanted to test the low power consumption, but when I saw that the board had to be cut, I decided to leave it for later and run the external flash function first.
1. Determine the hardware...
Principle Analysis
First, let's talk about the program image. A complete program image can be divided into two parts: "interrupt vector table" and "logic program" (let's name it this way for the conve...
In 2022, automobile standardization work will continue to be guided by Xi Jinping Thought on Socialism with Chinese Characteristics for a New Era, fully implement the spirit of the 19th National Cong...[Details]
The content of interrupt priority includes general urgent interrupts and special urgent interrupts. This depends on the specific system design. This involves the concepts of interrupt priority and in...[Details]
On May 12, clean technology company Nano One announced a partnership with the Brazilian Company for Mining and Metallurgy (CBMM) to jointly develop cathode materials for lithium-ion batteries. Nano O...[Details]
Basic knowledge of fuses
Fuses are indispensable in many electronic devices. Since Edison
invented the first plug-in fuse that enclosed a thin wire in a lamp holder in the 1890s, there hav...[Details]
On May 15, the high-efficiency dynamic UPS power system product jointly developed by the Energy Heavy Industry and Gas Turbine Company of China Energy Construction Gezhouba Equipment Company passed...[Details]
In the previous review of the vehicle EE architecture transformation process: with the introduction of Body Computer, cockpit and autonomous driving core computing platforms, the problem of high-spee...[Details]
Recently, the Shenzhen Development and Reform Commission issued the "Several Measures to Support the Accelerated Development of the Electrochemical Energy Storage Industry in Shenzhen (Draft for Co...[Details]
On August 5, 2016, in Hyderabad, India, Sungrow, a global leader in photovoltaic inverters, signed a 150MW centralized inverter supply contract with Mytrah Energy.
Sungrow provides a complete ...[Details]
Let me introduce the winding method of the high-frequency transformer in the high-frequency inverter. The winding method of the self-excited high-frequency transformer is the same.
If y...[Details]
Multiple sources claim that this year’s iPhone 15 series will use a USB-C interface. However, analysts pointed out that Apple may encrypt the USB-C interface for the purpose of protecting accessori...[Details]
Central topic: Both amplitude response and phase frequency response can affect the pulse response effect. Pulse response optimization can reduce the negative effects of amplitude frequency response o...[Details]
In response to recent rumors that Jia Yueting's electric car startup FF is facing restructuring and that Jia Yueting himself has resigned as CEO, FF responded to reporters that the company had alread...[Details]
On January 24, 2024, Wang Zhanshan, member of the Standing Committee of the Yu County Party Committee and Deputy County Magistrate of Yangquan City, Shanxi Province, Li Junyi, Director of the Yu Co...[Details]
According to MoneyDJ, LED packaging giant Everlight has been affected by competition from the red supply chain and falling LED prices since 2019, and its revenue has continued to decline. It is estim...[Details]
There are significant differences between the 6410 DMA controller and the 2440 DMA controller.
DMA operation steps in S3C6410:
1. Decide whether to use secure DMAC (SDMAC) or general DMAC...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
