16-Mbit 3.0V Serial Flash Memory with Uniform 4 kB Sectors
Data Sheet
S25FL216K Cover Sheet
Notice to Readers:
This document states the current technical specifications regarding the Spansion
product(s) described herein. Each product described herein may be designated as Advance Information,
Preliminary, or Full Production. See
Notice On Data Sheet Designations
for definitions.
Publication Number S25FL216K_00
Revision
10
Issue Date
September 16, 2013
D a t a
S h e e t
Notice On Data Sheet Designations
Spansion Inc. issues data sheets with Advance Information or Preliminary designations to advise readers of
product information or intended specifications throughout the product life cycle, including development,
qualification, initial production, and full production. In all cases, however, readers are encouraged to verify
that they have the latest information before finalizing their design. The following descriptions of Spansion data
sheet designations are presented here to highlight their presence and definitions.
Advance Information
The Advance Information designation indicates that Spansion Inc. is developing one or more specific
products, but has not committed any design to production. Information presented in a document with this
designation is likely to change, and in some cases, development on the product may discontinue. Spansion
Inc. therefore places the following conditions upon Advance Information content:
“This document contains information on one or more products under development at Spansion Inc.
The information is intended to help you evaluate this product. Do not design in this product without
contacting the factory. Spansion Inc. reserves the right to change or discontinue work on this proposed
product without notice.”
Preliminary
The Preliminary designation indicates that the product development has progressed such that a commitment
to production has taken place. This designation covers several aspects of the product life cycle, including
product qualification, initial production, and the subsequent phases in the manufacturing process that occur
before full production is achieved. Changes to the technical specifications presented in a Preliminary
document should be expected while keeping these aspects of production under consideration. Spansion
places the following conditions upon Preliminary content:
“This document states the current technical specifications regarding the Spansion product(s)
described herein. The Preliminary status of this document indicates that product qualification has been
completed, and that initial production has begun. Due to the phases of the manufacturing process that
require maintaining efficiency and quality, this document may be revised by subsequent versions or
modifications due to changes in technical specifications.”
Combination
Some data sheets contain a combination of products with different designations (Advance Information,
Preliminary, or Full Production). This type of document distinguishes these products and their designations
wherever necessary, typically on the first page, the ordering information page, and pages with the DC
Characteristics table and the AC Erase and Program table (in the table notes). The disclaimer on the first
page refers the reader to the notice on this page.
Full Production (No Designation on Document)
When a product has been in production for a period of time such that no changes or only nominal changes
are expected, the Preliminary designation is removed from the data sheet. Nominal changes may include
those affecting the number of ordering part numbers available, such as the addition or deletion of a speed
option, temperature range, package type, or V
IO
range. Changes may also include those needed to clarify a
description or to correct a typographical error or incorrect specification. Spansion Inc. applies the following
conditions to documents in this category:
“This document states the current technical specifications regarding the Spansion product(s)
described herein. Spansion Inc. deems the products to have been in sufficient production volume such
that subsequent versions of this document are not expected to change. However, typographical or
specification corrections, or modifications to the valid combinations offered may occur.”
Questions regarding these document designations may be directed to your local sales office.
2
S25FL216K_00_10 September 16, 2013
S25FL216K
16-Mbit 3.0V Serial Flash Memory with Uniform 4 kB Sectors
Data Sheet
Distinctive Features
Single power supply operation
– Full voltage range: 2.7 to 3.6V
Flexible Architecture with 4 kB Sectors
–
–
–
–
–
Sector Erase (4 kB)
Block Erase (64 kB)
Page Program up to 256 bytes
100k erase/program cycles typical
20-year data retention typical
16-Mbit Serial Flash
– 16-Mbit/2048 kbyte/9192 pages
– 256 bytes per programmable page
– Uniform 4-kbyte Sectors/64-kbyte Blocks
Standard and Dual
–
–
–
–
Standard SPI: SCK, CS#, SI, SO, WP#, HOLD#
Dual SPI: SCK, CS#, SI/IO0, SO, WP#, HOLD#
Fast Read Dual Output instruction
Auto-increment Read capability
Software and Hardware Write Protection
– Write Protect all or portion of memory via software
– Enable/Disable protection with WP# pin
High Performance Program/Erase Speed
–
–
–
–
Page program time: 1.6 ms typical
Sector erase time (4 kB): 45 ms typical
Block erase time (64 kB): 450 ms typical
Chip erase time: 12 seconds typical
High Performance
– FAST READ (Serial): 65 MHz clock rate
– DUAL OUTPUT READ: 65 MHz clock rate
Low Power Consumption
– 12 mA typical active current
– 15 µA typical standby current
Package Options
– 8-pin SOIC 150/208-mil
– All Pb-free packages are RoHS compliant
General Description
The S25FL216K device is a 16-Mbit, 2048-kbyte Serial Flash memory, with advanced write protection mechanisms. The
S25FL216K supports the standard Serial Peripheral Interface (SPI), and a high performance Dual output using SPI pins: Serial
Clock, Chip Select, Serial SI/IO0, SO, WP#, and HOLD#. SPI clock frequencies of up to 65 MHz are supported.
The S25FL216K array is organized into 8,192 programmable pages of 256 bytes each. Up to 256 bytes can be programmed at
a time. Pages can be erased in groups of 16 (4-kB Sector Erase), groups of 256 (64-kB Block Erase) or the entire chip (Chip
Erase). The S25FL216K has 512 erasable sectors and 32 erasable blocks. The small 4 kB sectors allow for greater flexibility in
applications that require data and parameter storage.
A Hold pin, Write Protect Pin and programmable write protection provide further control flexibility. Additionally, the S25FL216K
device supports JEDEC standard manufacturer and device identification.
Publication Number S25FL216K_00
Revision
10
Issue Date
September 16, 2013
This document states the current technical specifications regarding the Spansion product(s) described herein. Spansion Inc. deems the products to have been in sufficient pro-
duction volume such that subsequent versions of this document are not expected to change. However, typographical or specification corrections, or modifications to the valid com-
FP6298 is a current control mode boost converter with pulse width modulation and built-in 80mΩ, 4.5A, 12V MOSFET. It can achieve maximum power and high conversion efficiency. Fewer peripheral compo...[Details]
1. Circuit The attached figure is a schematic diagram of the circuit for controlling digital display by AT90S8515 (only the circuit for the interface with the digital tube is drawn in the figure, and...[Details]
Compared with analog circuit electronic instruments, stepper motor instruments have uniform graduations, good pointer repeatability, fast response speed, small jitter, and fundamentally guarantee...[Details]
Welding technology is a very important process in the industrial manufacturing process. Generally speaking, welding technology is used wherever metal materials are processed. However, welding is al...[Details]
1. Introduction
With the continuous development of information processing technology, especially the widespread application of computers and the rapid development of the Internet, modern infor...[Details]
To judge whether it is good or bad: set the turntable to the ( ) position, insert the red test lead into the first hole on the right, and insert the black test lead into the second hole on the right....[Details]
GlobalFoundries CEO Tom Caulfield said the company has been running at insufficient capacity since August 2020, with capacity utilization exceeding 100%, and all capacity until the end of 2023 is cur...[Details]
Nowadays, white light LED lighting has been put into practical use and industrialized, and its light efficiency has surpassed that of traditional incandescent lamps and fluorescent lamps, fully d...[Details]
OFweek Cup · OFweek 2023 China
Robot
Industry Annual Selection (abbreviated as OFweek Robot Awards 2023) is jointly organized by OFweek, China's high-tech industry portal, and its authorita...[Details]
The Galaxy Z Fold3 5G is Samsung's first foldable phone to support the S Pen stylus, but the phone cannot be used with the regular S Pen. The Galaxy Z Fold 3 is only compatible with the S Pen ...[Details]
"We chose Seeker because testers and developers don't need to invest a lot of time or have very specialized knowledge to perform security testing tasks regularly," said the Chief Information Security...[Details]
Introduction: Embedded operating system is the software foundation of ARMCPU. From 8-bit/16-bit single-chip microcomputer to 32-bit embedded processor represented by ARMCPU core, embedded operating s...[Details]
Not long ago, the National Development and Reform Commission and seven other departments jointly issued the "Implementation Plan for Promoting Green Consumption". Among them, the reiteration of "vigo...[Details]
Power
adapters are widely used in laptops, game consoles, printers, DSL modems, and
mobile phones
, and the application scale is very large. From the perspective of people's usage hab...[Details]
京公网安备 11010802033920号
EEWORLD
