ST60 SMT HORN ANTENNA - V POLARIZATION - GOLD PLATING
PAGE
1/5
ISSUE
10-10-19A
SERIES
ANTENNA
PART NUMBER
R380845102
All dimensions are in mm.
COMPONENTS
Body
MATERIALS
LCP (Liquid
Cristal Polymer)
Gold
PLATING (m)
This document contains proprietary information and such information shall not be disclosed to any third party for any purpose whatsoever or used for manufacturing purposes without prior written
agreement from Radiall. The data defined in this document are given as an indication, in the effort to improve our products; we reserve the right to make any changes judged necessary.
Technical Data Sheet
ST60 SMT HORN ANTENNA - V POLARIZATION - GOLD PLATING
PAGE
2/5
ISSUE
10-10-19A
SERIES
ANTENNA
PART NUMBER
R380845102
ELECTRICAL CHARACTERISTICS
Frequency Band
Nominal Impedance
Return Loss
(1)
Typical Far-Field Directivity
Radiation Pattern
Polarization
Relative Cross-Polarization Level
ESD Protection
57 ~ 66
50
< -10
> 8
Directional
Linear Vertical
> 20
DC-Ground
dB
GHz
dB (Typ.)
dBi
(Horn)
Weight
MECHANICAL CHARACTERISTICS
0.11
8.25 × 7.4 × 3.4
Edge-Card SMT
g
mm
Overall Dimensions
Mounting Type
ENVIRONMENTAL CHARACTERISTICS
Extreme Storage Temperature
(2)
Recommended Storage
(2)
(12
Months Shelf Life)
(2)
Reflow Temperature
Operating Temperature Range
ROHS Compliant
REACH Compliant
-20 / +55
25 ± 15
30 ~ 60
260
-40 / +85
Yes
Yes
°C
°C
%RH
°C Max.
°C
(1):
Measured on Reference Board (See Application Note
“201910575-10_ _ _ - _ _ - _ _ A_AN.pdf”).
(2):
Tape & Reel Packaging Conditions
PACKAGING SUFFIX
P/N Suffix
20
01
Packaging Type
OD
ID
Large Reel
15’’
4’’
Small Reel
7’’
2.4’’
Other Packaging Available Upon Request
Order Quantity
2000
100
R380845102- _ _
PACKAGING REEL
This document contains proprietary information and such information shall not be disclosed to any third party for any purpose whatsoever or used for manufacturing purposes without prior written
agreement from Radiall. The data defined in this document are given as an indication, in the effort to improve our products; we reserve the right to make any changes judged necessary.
Technical Data Sheet
ST60 SMT HORN ANTENNA - V POLARIZATION - GOLD PLATING
PAGE
3/5
ISSUE
10-10-19A
SERIES
ANTENNA
PART NUMBER
R380845102
CARRIER TAPE
SHADOW FOR VIDEO CAMERA
This document contains proprietary information and such information shall not be disclosed to any third party for any purpose whatsoever or used for manufacturing purposes without prior written
agreement from Radiall. The data defined in this document are given as an indication, in the effort to improve our products; we reserve the right to make any changes judged necessary.
Technical Data Sheet
ST60 SMT HORN ANTENNA - V POLARIZATION - GOLD PLATING
PAGE
4/5
ISSUE
10-10-19A
SERIES
ANTENNA
PART NUMBER
R380845102
TYPICAL SOLDER MASK & PAD
SOLDER PASTE (For
80~100µ Thickness Screens)
This document contains proprietary information and such information shall not be disclosed to any third party for any purpose whatsoever or used for manufacturing purposes without prior written
agreement from Radiall. The data defined in this document are given as an indication, in the effort to improve our products; we reserve the right to make any changes judged necessary.
Technical Data Sheet
ST60 SMT HORN ANTENNA - V POLARIZATION - GOLD PLATING
PAGE
5/5
ISSUE
10-10-19A
SERIES
ANTENNA
PART NUMBER
R380845102
SOLDER PROCEDURE
1.
Deposit solder paste ‘SnAg4Cu0.5’ (T4
or T5)
on mounting zone by screen printing application. We recommend a low residue flux.
We advise a thickness of 80 to 100 µm (3,150
to 3,940 mils).
Verify that the edges of the zone are clean.
Placement of the receptacle on the mounting zone with an automatic machine of ‘pick and place’ type. A video camera is
recommended for positioning of the component. Adhesive agents must not be used on the receptacle.
This process of soldering has been tested with convection oven .Below please find, the typical profile to use.
The cleaning of printed circuit boards is possible, but not mandatory.
Verification of solder joints and position of the component by visual inspection (Component
centered on pads, with 100µm max. gap
between its shoulder & PCB edge).
2.
3.
4.
5.
TEMPERATURE PROFILE
Parameter
Temperature rising Area
Max Peak Temperature
Max dwell time @260°C
Min dwell time @235°C
Max dwell time @235°C
Temperature drop in
cooling Area
Max dwell time above
100°C
Value
1 -4
260
10
20
60
-1 to - 4
420
Unit
°C/sec
°C
sec
sec
sec
°C/sec
sec
This document contains proprietary information and such information shall not be disclosed to any third party for any purpose whatsoever or used for manufacturing purposes without prior written
agreement from Radiall. The data defined in this document are given as an indication, in the effort to improve our products; we reserve the right to make any changes judged necessary.
With the continuous development of the automobile industry, the degree of electrification is getting deeper and deeper, so the electrical system stability of various front/rear mounted equipment is be...
1. Experimental purpose:Namisoft requires students to design a spectrum analyzer. The sampling frequency, number of sampling points, signal frequency, amplitude and phase of the signal can be set on t...
[i=s]This post was last edited by gyp1 on 2019-9-9 23:21[/i]Calibration and use in PCB mode
Before using PCB mode, you need to calibrate according to the size of the PCB trace:First confirm the specif...
STM32CubeMX and STM32Cube HAL basics：https://training.eeworld.com.cn/course/5495This MOOC is targeting anyone who starts working on STM32 by introducing STM32 ecosystem.? You need some knowledge in C ...
[i=s]This post was last edited by lbbook on 2019-12-25 19:40[/i]Series of posts:
1. AWR1843BOOST unboxing
2. Use of AWR1843BOOST
After unboxing and getting familiar with the use of the mmWave Demo Vis...
With the continuous improvement of the living standards of urban and rural residents in my country, private cars have entered thousands of households at a rapid pace. However, in the old driver's lice...[Details]
Recently, the Gansu Provincial People's Government released the 2023 Government Work Report, which mentioned:
Cultivate and expand emerging industries. Vigorously develop new energy, new mater...[Details]
Shenzhen Newdi Technology Development Co., Ltd. ("Newdi Technology", or "NDT"), an industry-leading provider of pressure-sensitive touch solutions, recently attended the online seminar "Discussion on...[Details]
On the 24th of this month, Xiaomi 9 Pro was officially released. What’s interesting is that such a 5G mobile phone was reduced in price in disguise as soon as it was released. Currently, China Mobile...[Details]
This system is a host electronic control system, which completes parameter diagnosis, data acquisition, closed-loop control and other real-time control functions in the process of beam alignment, a...[Details]
Purpose: To use the remote control to communicate with the microcontroller, and display the codes corresponding to the remote control buttons in hexadecimal format on the digital tube. The IO port ...[Details]
Infrared thermal wave nondestructive testing technology (abbreviated as thermal wave testing) is a general practical technology that is cross-disciplinary and cross-application field. It is an innov...[Details]
Mitsubishi FX series PLC is a programmable logic controller widely used in the field of industrial automation. In the FX series PLC, the auxiliary relay is an important soft component used to imple...[Details]
Recently, a user in Jinan City, Shandong Province received a virtual power plant spot electricity bill, which indicates that the virtual power plant agent aggregation user has officially participated ...[Details]
It is reported that Apple recently obtained a new patent for automotive safety, including seat belts and roof airbags. Judging from the patent, Apple Car will change the design of the sunroof and d...[Details]
NVIDIA Expands Omniverse Cloud to Advance Digitalization in Industry
Microsoft Azure is launching the new Omniverse Cloud Platform-as-a-Service, following early Omniverse users such ...[Details]
Part 1: Digital Tube 1. Basic knowledge 1. Digital tube pin definition (single digital tube) The upper one is the common cathode connection The bottom one is the common anode connection Divide "8...[Details]
I. Introduction
With the continuous development of electronic technology , many household electrical appliances such as color TVs, refrigerators, air conditioners, etc. have been labeled as i...[Details]
On January 7, HuaWei Electronics stated on the investor interaction platform: "So far, our company has cooperated with China Electronics Technology Group Corporation 46 Institute on silicon epitaxial...[Details]
0 Introduction
The RF power amplifier is a device that converts the low-power RF signal in the transmitter into a sufficiently large RF power through a series of amplification stages: exci...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
