AEC Q100 Grade 1 Compliant
FM25L04 –
Automotive Temp.
4Kb FRAM Serial 3V Memory
Features
4K bit Ferroelectric Nonvolatile RAM
•
Organized as 512 x 8 bits
•
Unlimited Read/Write Cycles
•
NoDelay™ Writes
•
Advanced High-Reliability Ferroelectric Process
Fast Serial Peripheral Interface - SPI
•
Up to 10 MHz Frequency
•
Direct Hardware Replacement for EEPROM
•
SPI Mode 0 & 3 (CPOL, CPHA=0,0 & 1,1)
Write Protection Scheme
•
Hardware Protection
•
Software Protection
Low Power Consumption
•
Low Voltage Operation 3.0-3.6V
•
1
µA
Standby Current (+85°C)
Industry Standard Configuration
•
Automotive Temperature -40°C to +125°C
o
Qualified to AEC Q100 Specification
•
“Green”/RoHS 8-pin SOIC
Description
The FM25L04 is a 4-kilobit nonvolatile memory
employing an advanced ferroelectric process. A
ferroelectric random access memory or FRAM is
nonvolatile and performs reads and writes like a
RAM. It provides reliable data retention for years
while eliminating the complexities, overhead, and
system level reliability problems caused by
EEPROM and other nonvolatile memories.
Unlike serial EEPROMs, the FM25L04 performs
write operations at bus speed. No write delays are
incurred. The next bus cycle may commence
immediately without the need for data polling. The
next bus cycle may start immediately. In addition, the
product offers virtually unlimited write endurance.
Also, FRAM exhibits much lower power
consumption than EEPROM.
These capabilities make the FM25L04 ideal for
nonvolatile memory applications requiring frequent
or rapid writes or low power operation. Examples
range from data collection, where the number of
write cycles may be critical, to demanding
automotive controls where the long write time of
EEPROM can cause data loss.
The FM25L04 provides substantial benefits to users
of serial EEPROM as a hardware drop-in
replacement. The FM25L04 uses the high-speed SPI
bus, which enhances the high-speed write capability
of FRAM technology. Device specifications are
guaranteed over an automotive temperature range of
-40°C to +125°C.
Pin Configuration
CS
SO
WP
VSS
1
2
3
4
8
7
6
5
VDD
HOLD
SCK
SI
Pin Name
/CS
/WP
/HOLD
SCK
SI
SO
VDD
VSS
Function
Chip Select
Write Protect
Hold
Serial Clock
Serial Data Input
Serial Data Output
Supply Voltage
Ground
Ordering Information
FM25L04-GA
“Green”/RoHS 8-pin SOIC
This product conforms to specifications per the terms of the Ramtron
standard warranty. The product has completed Ramtron’s internal
qualification testing and has reached production status.
Ramtron International Corporation
1850 Ramtron Drive, Colorado Springs, CO 80921
(800) 545-FRAM, (719) 481-7000
http://www.ramtron.com
Rev. 3.0
Sept. 2007
Page 1 of 12
FM25L04 - Automotive Temp.
WP
CS
HOLD
SCK
Instruction Decode
Clock Generator
Control Logic
Write Protect
128 x 32
FRAM Array
Instruction Register
`
SI
Address Register
Counter
9
8
Data I/O Register
3
Nonvolatile Status
Register
SO
Figure 1. Block Diagram
Pin Descriptions
Pin Name
/CS
I/O
Input
Description
Chip Select: This active low input activates the device. When high, the device enters
low-power standby mode, ignores other inputs, and all outputs are tri-stated. When low,
the device internally activates the SCK signal. A falling edge on /CS must occur prior to
every op-code.
Serial Clock: All I/O activity is synchronized to the serial clock. Inputs are latched on
the rising edge and outputs occur on the falling edge. Since the device is static, the
clock frequency may be any value between 0 and 10 MHz and may be interrupted at
any time.
Hold: The /HOLD pin is used when the host CPU must interrupt a memory operation
for another task. When /HOLD is low, the current operation is suspended. The device
ignores any transition on SCK or /CS. All transitions on /HOLD must occur while SCK
is low.
Write Protect: This active low pin prevents write operations to the memory array and to
the Status Register. A complete explanation of write protection is provided below.
Serial Input: All data is input to the device on this pin. The pin is sampled on the rising
edge of SCK and is ignored at other times. It should always be driven to a valid logic
level to meet IDD specifications.
* SI may be connected to SO for a single pin data interface.
Serial Output: This is the data output pin. It is driven during a read and remains tri-
stated at all other times including when /HOLD is low. Data transitions are driven on
the falling edge of the serial clock.
* SO may be connected to SI for a single pin data interface.
Power Supply (3.0V to 3.6V)
Ground
SCK
Input
/HOLD
Input
/WP
SI
Input
Input
SO
Output
VDD
VSS
Supply
Supply
Rev. 3.0
Sept. 2007
Page 2 of 12
FM25L04 - Automotive Temp.
Overview
The FM25L04 is a serial FRAM memory. The
memory array is logically organized as 512 x 8 and is
accessed using an industry standard Serial Peripheral
Interface or SPI bus. Functional operation of the
FRAM is similar to serial EEPROMs. The major
difference between the FM25L04 and a serial
EEPROM with the same pinout is the FRAM’s
superior write performance and power consumption.
performance serial communication to a host
microcontroller. Many common microcontrollers
have hardware SPI ports allowing a direct interface.
It is quite simple to emulate the port using ordinary
port pins for microcontrollers that do not. The
FM25L04 operates in SPI Mode 0 and 3.
The SPI interface uses a total of four pins: clock,
data-in, data-out, and chip select. A typical system
configuration uses one or more FM25L04 devices
with a microcontroller that has a dedicated SPI port,
as Figure 2 illustrates. Note that the clock, data-in,
and data-out pins are common among all devices.
The Chip Select and Hold pins must be driven
separately for each FM25L04 device.
For a microcontroller that has no dedicated SPI bus, a
general purpose port may be used. To reduce
hardware resources on the controller, it is possible to
connect the two data pins (SI, SO) together and tie
off (high) the /HOLD pin. Figure 3 shows a
configuration that uses only three pins.
Protocol Overview
The SPI interface is a synchronous serial interface
using clock and data pins. It is intended to support
multiple devices on the bus. Each device is activated
using a chip select. Once chip select is activated by
the bus master, the FM25L04 will begin monitoring
the clock and data lines. The relationship between the
falling edge of /CS, the clock and data is dictated by
the SPI mode. The device will make a determination
of the SPI mode on the falling edge of each chip
select. While there are four such modes, the
FM25L04 supports Modes 0 and 3. Figure 4 shows
the required signal relationships for Modes 0 and 3.
For both modes, data is clocked into the FM25L04 on
the rising edge of SCK and data is expected on the
first rising edge after /CS goes active. If the clock
begins from a high state, it will fall prior to beginning
data transfer in order to create the first rising edge.
The SPI protocol is controlled by op-codes. These
op-codes specify the commands to the device. After
/CS is activated the first byte transferred from the bus
master is the op-code. Following the op-code, any
addresses and data are then transferred. Note that the
WREN and WRDI op-codes are commands with no
subsequent data transfer.
Important: The /CS must go inactive (high) after
an operation is complete and before a new op-code
can be issued. There is one valid op-code only per
active chip select.
Memory Architecture
When accessing the FM25L04, the user addresses
512 locations of 8 data bits each. These data bits are
shifted serially. The addresses are accessed using the
SPI protocol, which includes a chip select (to permit
multiple devices on the bus), an op-code, and an
address. The upper address bit is included in the op-
code. The complete address of 9-bits specifies each
byte address uniquely.
Most functions of the FM25L04 either are controlled
by the SPI interface or are handled automatically by
on-board circuitry. The access time for memory
operation is essentially zero, beyond the time needed
for the serial protocol. That is, the memory is read or
written at the speed of the SPI bus. Unlike an
EEPROM, it is not necessary to poll the device for a
ready condition since writes occur at bus speed. So,
by the time a new bus transaction can be shifted into
the device, a write operation will be complete. This is
explained in more detail in the interface section.
Users expect several obvious system benefits from
the FM25L04 due to its fast write cycle and high
endurance as compared with EEPROM. In addition
there are less obvious benefits as well. For example
in a high noise environment, the fast-write operation
is less susceptible to corruption than an EEPROM
since it is completed quickly. By contrast, an
EEPROM requiring milliseconds to write is
vulnerable to noise during much of the cycle.
Note that the FM25L04 contains no power
management circuits other than a simple internal
power-on reset. It is the user’s responsibility to
ensure that V
DD
is within datasheet tolerances to
prevent incorrect operation. It is recommended
that the part is not powered down with chip
enable active.
Serial Peripheral Interface – SPI Bus
The FM25L04 employs a Serial Peripheral Interface
(SPI) bus. It is specified to operate at speeds up to 10
MHz. This high-speed serial bus provides high
Rev. 3.0
Sept. 2007
Page 3 of 12
FM25L04 - Automotive Temp.
SCK
MOSI
MISO
SO
SPI
Microcontroller
SI
SCK
SO
SI SCK
FM25L04
CS
HOLD
FM25L04
CS
SS1
SS2
HOLD1
HOLD2
HOLD
MOSI : Master Out Slave In
MISO : Master In Slave Out
SS : Slave Select
Figure 2. System Configuration with SPI port
Figure 3. System Configuration without SPI port
SPI Mode 0: CPOL=0, CPHA=0
7
6
5
4
3
2
1
0
SPI Mode 3: CPOL=1, CPHA=1
7
6
5
4
3
2
1
0
Figure 4. SPI Modes 0 & 3
Rev. 3.0
Sept. 2007
Page 4 of 12
FM25L04 - Automotive Temp.
Data Transfer
All data transfers to and from the FM25L04 occur in
8-bit groups. They are synchronized to the clock
signal (SCK), and they transfer most significant bit
(MSB) first. Serial inputs are registered on the rising
edge of SCK. Outputs are driven from the falling
edge of SCK.
Command Structure
There are six commands called op-codes that can be
issued by the bus master to the FM25L04. They are
listed in the table below. These op-codes control the
functions performed by the memory. They can be
divided into three categories. First, there are
commands that have no subsequent operations. They
perform a single function such as to enable a write
operation. Second are commands followed by one
byte, either in or out. They operate on the Status
Register. The third group includes commands for
memory transactions followed by address and one or
more bytes of data.
Table 1. Op-code Commands
Name
Description
Set Write Enable Latch
WREN
Write Disable
WRDI
Read Status Register
RDSR
Write Status Register
WRSR
Read Memory Data
READ
WRITE
Write Memory Data
WREN - Set Write Enable Latch
The FM25L04 will power up with writes disabled.
The WREN command must be issued prior to any
write operation. Sending the WREN op-code will
allow the user to issue subsequent op-codes for
write operations. These include writing the Status
Register and writing the memory.
Sending the WREN op-code causes the internal
Write Enable Latch to be set. A flag bit in the Status
Register, called WEL, indicates the state of the
latch. WEL=1 indicates that writes are permitted.
Attempting to write the WEL bit in the Status
Register has no effect. Completing any write
operation will automatically clear the write-enable
latch and prevent further writes without another
WREN command. Figure 5 below illustrates the
WREN command bus configuration.
WRDI - Write Disable
The WRDI command disables all write activity by
clearing the Write Enable Latch. The user can verify
that writes are disabled by reading the WEL bit in
the Status Register and verifying that WEL=0.
Figure 6 illustrates the WRDI command bus
configuration.
Op-code
0000
0000
0000
0000
0000
0000
0110b
0100b
0101b
0001b
A011b
A010b
CS
0
SCK
1
2
3
4
5
6
7
SI
SO
0
0
0
0
Hi-Z
0
1
1
0
Figure 5. WREN Bus Configuration
CS
0
SCK
1
2
3
4
5
6
7
SI
SO
0
0
0
0
Hi-Z
0
1
0
0
Figure 6. WRDI Bus Configuration
Rev. 3.0
Sept. 2007
Page 5 of 12
京公网安备 11010802033920号
EEWORLD
