PRA135I21K26R0.5%0.01% datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> PRA135I21K26R0.5%0.01%

PRA135I21K26R0.5%0.01%: DescriptionArray/Network Resistor, Isolated, Thin Film, 0.125W, 1260ohm, 100V, 0.5% +/-Tol, -10,10ppm/Cel, 1107,; CategoryPassive components The resistor; File Size80KB，5 Pages; ManufacturerVishay; Websitehttp://www.vishay.com

Download Datasheet Parametric View All

PRA135I21K26R0.5%0.01% Overview

Array/Network Resistor, Isolated, Thin Film, 0.125W, 1260ohm, 100V, 0.5% +/-Tol, -10,10ppm/Cel, 1107,

PRA135I21K26R0.5%0.01% Parametric

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
Objectid	982906033
package instruction	SMT, 1107
Reach Compliance Code	compliant
Country Of Origin	France
ECCN code	EAR99
YTEOL	7.1
structure	Chip
Network Type	Isolated
Number of terminals	4
Maximum operating temperature	155 °C
Minimum operating temperature	-55 °C
Package height	0.4 mm
Package length	2.7 mm
Package form	SMT
Package width	1.85 mm
method of packing	Box
Rated power dissipation(P)	0.125 W
resistance	1260 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	PRA (CNW)
size code	1107
technology	THIN FILM
Temperature Coefficient	10 ppm/°C
Tolerance	0.5%
Operating Voltage	100 V

Preview

Download Datasheet

View All

PRA 100, 135, 182 (CNW)

Vishay Sfernice

High Precision Resistor Chip Arrays

FEATURES

•

High stability passivated nichrome resistive

layer 0.02 % on ratio, 1000 h at Pn at + 70 °C

•

Tight TCR (10 ppm/°C) and TCR tracking

(to 1 ppm/°C)

•

Very low noise < 35 dB and voltage coefficient

< 0.01 ppm/V

•

Ratio tolerance to 0.01 % (R

≥

200R)

•

Pre-tinned terminations over nickel barrier

•

High temperature option (200 °C)

•

SMD wraparound chip resistor array

•

Compliant to RoHS directive 2002/95/EC

PRA arrays can be used in most applications requiring a

matched pair (or set) of resistor elements. The networks

provide 1 ppm/°C TCR tracking, a ratio tolerance as tight as

0.01 % and outstanding stability. They are available in 1 mm,

1.35 mm and 1.82 mm pitch.

TYPICAL PERFORMANCE

ABS

TCR

TOL

10 ppm/°C

ABS

0.1 %

TRACKING

2 ppm/°C

RATIO

0.05 %

DIMENSIONS

Suggested Land Pattern

I: Independent resistors

Termination

Electrical diagram

DIM.

(1)

PRA 100

1.6

0.4

0.65

+ 0.2

- 0.1

+ 0.2

- 0.2

+ 0.15

- 0.15

PRA 135

mil

1.85

0.4

1.05

+ 0.2

- 0.1

+ 0.2

- 0.2

+ 0.15

- 0.15

PRA 182

mil

3.0

0.4

1.3

+ 0.2

- 0.1

+ 0.2

- 0.2

+ 0.35

- 0.15

mil

118

Number

of resistors:

2 to

R1 = R2 = ... R8

25.5

0.25

E = (N x F) ± 0.2 mm

0.4

+ 0.1

-0

E = (N x F) ± 8 mil

53.1

41.3

31.5

1.82

0.4

+ 0.1

-0

C: One common point

resistors

27.5

23.5

1.35

0.4

+ 0.1

-0

59.8

70.8

0.7

0.3

0.6

1.05

0.3

0.8

1.52

0.3

1.8

Note

(1)

E depends on number of resistors

* Pb containing terminations are not RoHS compliant, exemptions may apply

** Please see document “Vishay Material Category Policy”:

www.vishay.com/doc?99902

www.vishay.com

For technical questions, contact:

sfer@vishay.com

Number

of resistors:

2 to

R1 = R2 = ... R8

Document Number: 53033

Revision: 17-Aug-09

Recommended Resources

Simple water level controller circuit (2)

Current expansion circuit with external transistor and external NPN switch circuit diagram

Simple exposure meter circuit

Pressure detection circuit with 4~20mA current loop

555 intelligent electronic watchdog circuit

Stabilizer tube circuit

[Telink B91 Universal Development Kit] Questions about the functions of TX and RX on the burning tool: In the previous post (https://en.eeworld.com/bbs/thread-1219308-1-1.html), the program was successfully downloaded using the burning tool. Only the GND and SWM pins were used.In addition to these two ...; freeelectron RF/Wirelessly

FPGA Design Process: FPGA Design Process...; zxopenljx EE_FPGA Learning Park

Power supply obstacles + power supply SBC selection and pitfalls: Hello everyone, I am an automotive electronics hardware engineer. When selecting a power SBC, you should pay attention to the battery voltage range and then combine it with the test standards to selec...; 你好再见 Power technology

Sharing of key points on the use of ADI passive components: Sharing of key points on the use of ADI passive components...; 勤奋 ADI Reference Circuit

Wide voltage input USB-C, 5V/3A output adapter reference design: USB-C, DFP, 5V/3A output, 85-265VAC input, adapter, low cost reference designThe UCC28700 and TPS25810 are used to provide isolated 5 V at 3 A over the USB type C interface. The UCC28700 performs prim...; qwqwqw2088 Analogue and Mixed Signal

When the machine is turned off, the LDO output is normally 3V. Why does the voltage reach 3.5V after the machine is turned on? What is the reason?: When the machine is turned off, the LDO output is normally 3V. Why does the voltage reach 3.5V after the machine is turned on? What is the reason?...; QWE4562009 Integrated technical exchanges

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components