Above ratings are based on the thermal resistances using a multi-layer circuit board (EIA/JESD51). For mounting on a mono-layer board, power derating shall be
needed. Please inquire of us about conditions.
※1 素子毎の負荷電力の合計が、パッケージ定格電力を超えない条件で御½用ください。
※1 Total power consumption of all elements should not exceed the package power rating.
The resistor of this product is formed by narrow patterning a thin metal film. Thus, application of excessive voltage causes burn and destruction of the resistive film, abnormality
in resistance or open resistance and loss of proper function. The properly and electrostatically measured taping materials are used for the components, but attention should be paid
to the fact that there is some danger the parts may be destructed by static electricity(equivalent to 500V or over at 100pF, 1.5kΩ) to cause a change in resistance in the conditions
of an excessive dryness when mounting on the boards. Similarly, care should be given not to apply the excessive static electricity at the time of mounting on the boards. When
designing, consideration can be taken into withstanding ESD for customized KPC products. Please consult with us about the details.
●
Hand soldering by iron soldering or repairment are not recommended because KPC is a multi-pin product.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling
strength. In the case of 5〜35℃/35〜75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas
like hydrogen sulfide, sulfurous acid gas, hydrogen chloride, etc. may drop solderability.
FF0000 and 880000 are both red. What is the difference between these two reds?Another question is, are reds of different saturations pure red, or are they mixed with other colors?...
1. Brief Introduction
After completing the data request, you also need to write the software interface. The system comes with the LVGL graphical interface, but to be honest, using LVGL for monochrome ...
In mathematical terms, an FIR filter is a series of dot products. Take an input quantity and an ordinal vector, multiply the coefficients and a sliding window of input samples, and then add all the pr...
Impedance matching of power amplifiers
Higher Q values should be considered because higher Q values provide higher attenuation of the amplifier harmonics. Because current and voltage limiting in the o...
1. The motor is short-circuited to the ground. The test method is to use an megohmmeter with one end connected to the ground and the other end connected to the motor terminal. The insulation is zero ...[Details]
If an abnormal working state occurs during the operation of an integrated operational amplifier and no measures are taken, the circuit will be damaged. The protection of the integrated operational am...[Details]
According to Koreatime, Samsung is facing an investigation by the U.S. International Trade Commission (USITC) for allegedly infringing patents related to image sensor technology held by American comp...[Details]
0 Introduction
The temperature acquisition equipment widely used at present generally uses a single-chip microcomputer as the internal chip of the temperature control system. Its disadvantages are s...[Details]
The light source of LED
is composed of so-called III-V compounds, which are well-known epitaxial crystal grains (chips). The solid compound itself is very stable in nature and is not easily...[Details]
Now let's analyze how uboot starts the kernel. We know that the u-boot kernel startup is achieved through two instructions. nand read.jffs2 0x30007FC0 kernel; bootm 0x30007FC0 Reading the kerne...[Details]
In machine vision systems, it is crucial to obtain a high-quality processable image. The success of the system depends on ensuring good image quality and clear features. Most of the failures of a m...[Details]
Ways to reduce
the neutral voltage
include:
1) Shortening the length of the neutral line and increasing the cross-sectional area of the neutral line can reduce the neutral line...[Details]
In the past, LED manufacturers have developed large-size LED chips to achieve their desired goals in order to obtain sufficient
white light LED
beams. However, in reality, when the applie...[Details]
According to Jiwei.com, on June 25, China Merchants Securities recently disclosed a report summarizing the guidance work for Nanjing Guobo Electronics Co., Ltd.'s initial public offering and listing...[Details]
Self-excited Piezo Sounder driver from Diodes Corporation extends run time and maintains high SPL output throughout battery life Diodes Corporation (Diodes) will launch a new driver IC to meet the...[Details]
On October 18, NXP Semiconductors announced the launch of OrangeBox, an automotive-grade development platform. The platform integrates various NXP wireless technologies, including broadcast radio, Wi...[Details]
When debugging a program, we can use the method of viewing variables, but we still cannot leave the printing of debugging information. . . . . Before starting other experiments, first experiment with...[Details]
An oscilloscope is an instrument that displays the time-varying characteristics of a signal waveform. It can transform electrical signals that are invisible to the naked eye into visible images...[Details]
On January 9, after the AR navigation function was officially launched, Sogou Maps held a media communication meeting in Beijing. At the meeting, Sogou Maps head Kong Xianglai said that Sogou Maps is...[Details]
MCU
京公网安备 11010802033920号
EEWORLD
