177-710-5-69GP6J5-18BZG datasheet, PDF

Datasheet> All Categories > The connector> Connector bracket> 177-710-5-69GP6J5-18BZG

177-710-5-69GP6J5-18BZG: DescriptionCable Assembly, 26AWG,; CategoryThe connector Connector bracket; File Size858KB，5 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/; Environmental Compliance

Download Datasheet Parametric View All

177-710-5-69GP6J5-18BZG Overview

Cable Assembly, 26AWG,

177-710-5-69GP6J5-18BZG Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	7004974897
Reach Compliance Code	compliant
Country Of Origin	USA
YTEOL	8.75
Other features	STANDARD: MIL-DTL-83513, EMI SHIELDED
Certification	MIL
Conductor surface treatment	SILVER
conductor material	COPPER
ConnectorSide1	MICRO-D MALE
ConnectorSide2	MICRO-D MALE
Connector bracket type	CABLE ASSEMBLY
structure	STRANDED
Cross-sectional area	0.129 mm2
DIN compliance	NO
IEC compliance	NO
insulator material	CROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length	0.466 mm
MIL compliance	YES
Number of conductors	69
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Rated current	3 A
Rated voltage	150 V
resistance	0.147 Ω
shield	YES
stay	19X38
Wire gauge	26 AWG
Wire and Cable Names	FLEXIBLE CORD AND FIXTURE WIRE

Preview

Download Datasheet

View All

SHIELDING EFFECTIVENESS (Db)

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

SHIELDING EFFECTIVENESS (Db)

Micro-D Harness

EMI Performance with Ground Spring

100

1.00E+03

MWDM Micro-D

Shielded Cable Assembly

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly labor. 100%

tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

specification for Micro-D cables with twisted pairs. Glenair 177-740

cables are furnished with a full complement of white/blue twisted

pair wires.

Integral Shield Termination–The

connector shell has a platform

to accept Band-It shield termination bands. The cable shield braid is

attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding

with Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s

fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-

piece connector shell and secured with a stainless steel

Band-Master™ ATS

clamp. These pre-wired, 100% tested

assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low

shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be

ordered in any length, either single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

A gold-plated stainless steel ground spring on the pin connector mating

face offers substantial improvement in EMI protection. The graphs

compare identical connectors tested with and without ground springs.

EMI Performance without Ground Spring

100

1.00E+03

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

frequency (Hz)

High Performance Micro-D Connectors and Cables

U.S. CAGE Code 06324

Printed in U.S.A.

GLENAIR, INC.

•

1211 AIR WAY

•

GLENDALE, CA 91201-2497

•

818-247-6000

•

FAX 818-500-9912

www.glenair.com

B-14

E-Mail: sales@glenair.com

Recommended Resources

Power outage and incoming call alarm circuit 2

Programmable lantern controller circuit 03

Gantry milling machine regulated power supply schematic circuit

Water shortage alarm circuit

AC flash circuit

transistor or gate

ESP-USB-Bridge turns the ESP32-S2/S3 development board into a JTAG debugger, and cooperates with OpenOCD to debug STM32 and other chips: When studying the bare-metal programming of ESP32 series wireless MCU debugged by OpenOCD and the low-level assembly of xtensa LX6/LX7 and RISCV, it was found that there were two esp-related configura...; mars4zhu DigiKey Technology Zone

Analog Electronics Textbook Exercises: I would like to ask why there is no equivalent of T3 in this AC path? Also, where is the output of the differential amplifier circuit? Is it output through R1?...; xiaogelaosama Analog electronics

Teach you step by step: Use STM32F103 to drive ST7567 LCD screen: ST7567 is one of the driver chips for LCD screens. It is a single-chip dot matrix LCD driver that integrates an LCD controller and a common/segment driver. The display data sent from the MPU is stored...; 可乐zzZ stm32/stm8

CCS: Where to find Packsges in ccs...; 庞绍锐 TI Technology Forum

Download "ADI Arbitrary Waveform Generator Solution" and get a gift!: [font=微软雅黑][size=4][b][color=#ff0000][Event Time][/color][/b] From now on - January 20, 2019[/size][/font][font=微软雅黑][size=4] [/size][/font] [font=微软雅黑][size=4][color=#ff0000][b][Event Process][/b][/c...; EEWORLD社区 Test/Measurement

TTI and Molex live broadcast at 10 am today | Smaller, faster, more reliable connectors drive new developments in IoT applications: Live Details: Smaller, faster, more reliable connectors drive new developments in IoT applicationsLive broadcast time: July 31, 2019 (today) 10:00-11:30 amLive Topic: Smaller, faster, and more reliabl...; EEWORLD社区 Integrated technical exchanges

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components