EEWORLDEEWORLDEEWORLD

Part Number

Search

SFM13001JEANHWS

Description
Fixed Resistor, Thin Film, 0.25W, 13000ohm, 100V, 5% +/-Tol, -25,25ppm/Cel, 0202,
CategoryPassive components    The resistor   
File Size70KB,3 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance
Download Datasheet Parametric View All

SFM13001JEANHWS Overview

Fixed Resistor, Thin Film, 0.25W, 13000ohm, 100V, 5% +/-Tol, -25,25ppm/Cel, 0202,

SFM13001JEANHWS Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid985690226
Reach Compliance Codeunknown
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.6
structureChip
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height0.254 mm
Package length0.5 mm
Package formSMT
Package width0.5 mm
method of packingWaffle Pack
Rated power dissipation(P)0.25 W
resistance13000 Ω
Resistor typeFIXED RESISTOR
seriesSFM
size code0202
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Tolerance5%
Operating Voltage100 V
SFM
Vishay Electro-Films
Thin Film Top-Contact Resistor
CHIP
RESISTORS
FEATURES
Wire bondable
Product may not
be to scale
Small size: 0.020 inches square
Resistance range: 1.0
Ω
to 1 MΩ
DC power rating: 250 mW
Oxidized silicon substrate for good power dissipation
Resistor material tantalum nitride, self passivating
Moisture resistant
The SFM series single-value resistor chips offer a small size,
wide ohmic value range and excellent power capacity.
The SFMs tantalum nitride resistor material offers excellent
resistance to high moisture environments.
The SFMs are manufactured using Vishay Electro-Films
(EFI) sophisticated thin film equipment and manufacturing
technology. The SFMs are 100 % electrically tested and
visually inspected to MIL-STD-883.
APPLICATIONS
Vishay EFI SFM top-contact resistor chips are designed to handle substantial power loads in many types of hybrid packages.
They are ideally suited for this purpose because of their small size.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES AND TOLERANCES
Tightest Standard Tolerance Available
1%
0.5 %
0.1 %
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
± 250 ppm/°C
1
Ω
10
Ω
30
Ω
100
Ω
200 kΩ 360 kΩ 620 kΩ 1 MΩ
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
Noise, MIL-STD-202, Method 308
100
Ω
to 250 kΩ
< 100
Ω
or > 251 kΩ
Moisture Resistance, MIL-STD-202
Method 106
Stability, 1000 h, + 125 °C, 125 mW
Operating Temperature Range
Thermal Shock, MIL-STD-202,
Method 107, Test Condition F
High Temperature Exposure, + 150 °C, 100 h
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to Zero at + 175 °C)
5 x Rated Power Short-Time Overload, + 25 °C, 5 s
- 35 dB typ.
- 20 dB typ.
± 0.5 % max.
ΔR/R
± 0.25 % max.
ΔR/R
- 55 °C to + 125 °C
± 0.25 % max.
ΔR/R
± 0.5 % max.
ΔR/R
200 V
10
12
min.
100 V max.
250 mW
± 0.25 % max.
ΔR/R
www.vishay.com
38
For technical questions, contact:
efi@vishay.com
Document Number: 61017
Revision: 17-Aug-09
Infrared thermal imager recommendation
Hello everyone, are there any friends who use infrared thermal imagers in their work? The current demand is to monitor the temperature of the electric heating tube during operation and overload (the t...
UUC Test/Measurement
V853 Replace the startup LOGO
# The overview mainly describes how to replace the startup LOGO of V853 # Environmental software: V853 Tina 5.0 SDK Hardware: Allwinner V853 development board # Specific steps First, let's take a look...
aleksib Domestic Chip Exchange
The problem of the servo not rotating when the nodemcu esp8266 development board drives it
[i=s]This post was last edited by xiguabuda on 2022-3-11 22:59[/i]I'm new to this. I'm using a development board and MicroPython to drive the servo, but there's no response. Could you please help me f...
xiguabuda MicroPython Open Source section
Mentor Usage Problems
Dear experts, after installing Mentor DC7.9.2, when Capture Design calls the component library, it cannot be displayed, but the component library can be opened separately. Is there any problem with th...
随风飘啊 PCB Design
Ethernet Problems
Please help me, masters! This is the Ethernet interface circuit designed for the TM4C1294NCPDTI3 chip. It uses an interface socket with a built-in signal transformer, but the computer does not respond...
Simonbinbin Microcontroller MCU
If you want to know whether the signal generated by the signal generator or function generator is ready or whether it is input according to the set value standard...
If I want to know whether the signal generated by a signal generator or function generator is ready or output according to the set value standard, what instrument can be used to verify it? Please help...
QWE4562009 Integrated technical exchanges

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号