EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

AYC28HRAI

Description
Card Edge Connector, 28 Contact(s), 1/2 LOADED Row(s), Right Angle, 0.1 inch Pitch, Solder Terminal, #4-40, Green Insulator, Receptacle
CategoryThe connector    The connector   
File Size640KB,5 Pages
ManufacturerSullins Connector Solutions
Environmental Compliance  
Download Datasheet Parametric View All

AYC28HRAI Overview

Card Edge Connector, 28 Contact(s), 1/2 LOADED Row(s), Right Angle, 0.1 inch Pitch, Solder Terminal, #4-40, Green Insulator, Receptacle

AYC28HRAI Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1157019516
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresNONE
Board mount optionsMOUNTING FLANGE
body width0.33 inch
subject depth0.637 inch
body length3.675 inch
Body/casing typeRECEPTACLE
Connector typeCARD EDGE CONNECTOR
Contact to complete cooperationNOT SPECIFIED
Contact completed and terminatedGold (Au) - with Nickel (Ni) barrier
Contact materialBERYLLIUM COPPER
contact modeRECTANGULAR
Contact resistance10 mΩ
Contact styleBELLOWED TYPE
Dielectric withstand voltage600VDC V
maximum insertion force4.448 N
Insulation resistance5000000000 Ω
Insulator colorGREEN
insulator materialGLASS FILLED POLYPHENYLENE SULFIDE
JESD-609 codee4
Plug contact pitch0.1 inch
Installation option 1#4-40
Installation option 2THREADED
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number1,(1/2 LD)
Number of rows loaded1/2 LOADED
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness30u inch
Rated current (signal)3 A
reliabilityCOMMERCIAL
Terminal length0.125 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts28
Evacuation force-minimum value.278 N
What is the use of a diode in parallel with a pull-up resistor?
As shown in the figure, in addition to capacitors and resistors, a diode is connected in parallel to the pull-up resistor in the reset circuit of an Ethernet transceiver chip. What is the function of ...
lingking Analog electronics
Regarding the improvement suggestions after studying "PCB layout and thermal design system of high-density power system", please use the website as "Editor"...
Regarding the improvement suggestions after studying "PCB Layout and Thermal Design System of High-Density Power System" , please add to the website in the form of "Editor's Note". We really hope for ...
ppiicc Power technology
ESP-S3-12K (Part 2) ---- Let's power it up
[i=s]This post was last edited by RCSN on 2021-12-27 17:55[/i]I won't post the environment setup. After the environment is set up, burn helloworld, check the Log information, and turn on the psram tes...
RCSN Domestic Chip Exchange
Automotive 400W, 48V Battery Input, 12V Output Power Supply Reference Design
TI's TID A-01407 is a 400W automotive power reference design for 36V-60V input and 12V output. It uses an enhanced phase-shifted full-bridge controller to achieve programmable delays, thereby ensuring...
alan000345 Analogue and Mixed Signal
What to do next?
...
lanhua ST MEMS Sensor Creative Design Competition
Study on frequency requirements for 5G NR-V2X direct communication
Li Yan, Gao Lu(Qualcomm Wireless Technologies (China) Co., Ltd., Beijing 100013) Abstract: This paper studies the spectrum requirements of direct communication in 5G New Radio-Vehicle-to-Everything (N...
ohahaha RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号